AECMA PREN 4165-003-2006 Aerospace series Connectors electrical rectangular modular Operating temperature 175 continuous Part 003 Modules series 2 and series 3 Product standard E.pdf

《AECMA PREN 4165-003-2006 Aerospace series Connectors electrical rectangular modular Operating temperature 175 continuous Part 003 Modules series 2 and series 3 Product standard E.pdf》由会员分享，可在线阅读，更多相关《AECMA PREN 4165-003-2006 Aerospace series Connectors electrical rectangular modular Operating temperature 175 continuous Part 003 Modules series 2 and series 3 Product standard E.pdf（9页珍藏版）》请在麦多课文档分享上搜索。

1、ASD STANDARD NORME ASD ASD NORM prEN 4165-003 Edition P 2 July 2006 PUBLISHED BY THE AEROSPACE AND DEFENCE INDUSTRIES ASSOCIATION OF EUROPE - STANDARDIZATION Gulledelle 94 - B-1200 Brussels - Tel. + 32 2 775 8126 - Fax. + 32 2 763 3565 - www.asd-stan.orgICS: Supersedes edition P 1 December 2001 Desc

2、riptors: ENGLISH VERSION Aerospace series Connectors, electrical, rectangular, modular Operating temperature 175 C continuous Part 003: Modules series 2 and series 3 Product standard Srie arospatiale Connecteurs lectriques, rectangulaires, modulaires Temprature dutilisation 175 C continu Partie 003

3、: Modules srie 2 et srie 3 Norme de produit Luft- und Raumfahrt Elektrischer Rechtecksteckverbinder in modularer Bauweise Betriebstemperatur 175 C konstant Teil 003: Modul serie 2 und serie 3 Produktnorm This “Aerospace Series“ Prestandard has been drawn up under the responsibility of ASD-STAN (The

4、AeroSpace and Defence Industries Association of Europe - Standardization). It is published for the needs of the European Aerospace Industry. It has been technically approved by the experts of the concerned Domain following member comments. Subsequent to the publication of this Prestandard, the techn

5、ical content shall not be changed to an extent that interchangeability is affected, physically or functionally, without re-identification of the standard. After examination and review by users and formal agreement of ASD-STAN, it will be submitted as a draft European Standard (prEN) to CEN (European

6、 Committee for Standardization) for formal vote and transformation to full European Standard (EN). The CEN national members have then to implement the EN at national level by giving the EN the status of a national standard and by withdrawing any national standards conflicting with the EN. Edition ap

7、proved for publication 31 July 2006 Comments should be sent within six months after the date of publication to ASD-STAN Electrical Domain Copyright 2006 by ASD-STAN Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMA Not for ResaleNo rep

8、roduction or networking permitted without license from IHS-,-,-prEN 4165-003:20062 Contents Page 1 Scope 3 2 Normative references 3 3 Terms and definitions .3 4 Required characteristics.4 4.1 Male module interface dimensions Series 2 and series 3 4 4.2 Female module interface dimensions Series 2 and

9、 series 35 4.3 Male and female module size 08 contact Grommet design6 4.4 Blank module series 2 and series 3.6 4.5 Module interface dimensions .7 5 Male and female module cavities coding 7 6 Main general characteristics 8 7 Designation 8 7.1 Electrical modules .8 7.2 Blank module .9 8 Marking .9 9 T

10、echnical specification .9 This standard was reviewed by the Domain Technical Coordinator of ASD-STANs Electrical Domain. After inquiries and votes carried out in accordance with the rules of ASD-STAN defined in ASD-STANs General Process Manual, this standard has received approval for Publication. Co

11、pyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMA Not for ResaleNo reproduction or networking permitted without license from IHS-,-,-prEN 4165-003:20063 1 Scope This standard specifies the characteristics of module in the family of modul

12、ar connector coupled by central threaded coupling, or rack and panel. For contacts and fillers plug associated see EN 4165-002. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For

13、undated references, the latest edition of the referenced document (including any amendments) applies. EN 2424, Aerospace series Marking of aerospace products. EN 3155-002, Aerospace series Electrical contacts used in elements of connection Part 002: List and utilization of contacts. EN 4165-001, Aer

14、ospace series Connectors, electrical, rectangular, modular Operating temperature 175 C continuous Part 001: Technical specification Product standard. EN 4165-002, Aerospace series Connectors, electrical, rectangular, modular Operating temperature 175 C continuous Part 002: Specification of performan

15、ce and contact arrangements. 3 Terms and definitions For the purposes of this document, the terms and definitions given in EN 4165-001 apply. Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMA Not for ResaleNo reproduction or networking

16、 permitted without license from IHS-,-,-prEN 4165-003:20064 4 Required characteristics 4.1 Male module interface dimensions Series 2 and series 3 See Figure 1 and Table 1. Dimensions are in millimetres. Key 1 Polarizing keys see Figure 5. 4 Zone of contact (module grounded) 2 Optional design for sea

17、led version 5 2,001,00point of sealing feature 3 Interfacial seal see Figure 3. 6 Grommet Figure 1 Table 1 A C Mass without contacts g Size max. max. max. 22-20-16-12 16,46 13,35 3,0 8 18,70 11,65 2,3 Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under lic

18、ense with AECMA Not for ResaleNo reproduction or networking permitted without license from IHS-,-,-prEN 4165-003:2006 5 4.2 Female module interface dimensions Series 2 and series 3 See Figure 2 and Table 2. Dimensions are in millimetres. Key 1 Polarizing keys see Figure 5. 4 Zone of contact (module

19、grounded) 2 Optional design for sealed version 5 2,001,00point of sealing feature 3 Socket contact cavity see Figure 4. 6 Grommet Figure 2 Table 2 A max. B max. Size series 2 series 3 series 2 series 3 C max. 22-20-16-12 22,40 30,96 17,40 25,96 13,35 8 33,20 17,16 25,72 11,65 Copyright Association E

20、uropeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMA Not for ResaleNo reproduction or networking permitted without license from IHS-,-,-prEN 4165-003:20066 4.3 Male and female module size 08 contact Grommet design For series 2 and series 3. Key 1 Grommet Figure

21、 3 4.4 Blank module series 2 and series 3 Instead of male or female modules Figure 4 Male module Female module Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMA Not for ResaleNo reproduction or networking permitted without license from

22、 IHS-,-,-prEN 4165-003:2006 7 4.5 Module interface dimensions See EN 4165-001 Figures 20 and 21. 5 Male and female module cavities coding See Figure 5. Key 1 Marking area Figure 5 Standard position NPosition A Position B Position C Position D Copyright Association Europeene des Constructeurs de Mate

23、riel Aerospatial Provided by IHS under license with AECMA Not for ResaleNo reproduction or networking permitted without license from IHS-,-,-prEN 4165-003:20068 6 Main general characteristics See EN 4165-002. 7 Designation 7.1 Electrical modules EXAMPLE Description block ELECTRICAL MODULES Identity

24、block EN4165A04G161NA Number of this standard Module series (see EN 4165-002) series 2 = A series 3 = B (not for blanck module) Module arrangements and Grounding module device (see EN 4165-002) G = grounded Dash = no grounding Peripherical sealing Unsealed = 1 Sealead = 2 Polarisation (see Figure 5)

25、 N = Normal, or A, B, C, D Module and contact delivery (see Table 3) NOTE 1 If necessary, the code I9005 shall be placed between the description block and the identity block. NOTE 2 The previously used designation (e.g.: EN4165-04G16A1NA) is inactive for new design and should not be used as designat

26、ion anymore. Table 3 Types of contacts and delivery modules Modules type Delivered without contact Delivered with contacts with standard barrels a EN3155-xxxx2222 EN3155-xxxx2020 EN3155-xxxx1616 EN3155-xxxx1212 Delivered with specific contactssize 20 with special barrel aEN3155-xxxx2018 bMale module

27、 A M C Female module B F D aSee EN 3155-002. bOnly affects size 20 contact arrangements. Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMA Not for ResaleNo reproduction or networking permitted without license from IHS-,-,-prEN 4165-003

28、:20069 7.2 Blank module Blank module is available for all shells (receptacles and plugs) instead of male and female standard modules, in series 2 and series 3. EXAMPLE Description block BLANK MODULE Identity block EN4165-1N Number of the basic standard Peripherical sealing unsealed = 1 sealed = 2 Po

29、larisation N = Normal only 8 Marking Unless there are other specific contractual requirements, the marking shall be in accordance with EN 2424 category P. 9 Technical specification See EN 4165-001. Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMA Not for ResaleNo reproduction or networking permitted without license from IHS-,-,-