AECMA PREN 2358-1985 Aerospace Series Eye-Ends in Corrosion Resisting Steel Swaged on Type Control Cable Dimensions and Loads Edition 1《 航空和航天.用于操纵钢索的不锈钢带眼的钢索端头 尺寸和负荷.第1版》.pdf

《AECMA PREN 2358-1985 Aerospace Series Eye-Ends in Corrosion Resisting Steel Swaged on Type Control Cable Dimensions and Loads Edition 1《 航空和航天.用于操纵钢索的不锈钢带眼的钢索端头 尺寸和负荷.第1版》.pdf》由会员分享，可在线阅读，更多相关《AECMA PREN 2358-1985 Aerospace Series Eye-Ends in Corrosion Resisting Steel Swaged on Type Control Cable Dimensions and Loads Edition 1《 航空和航天.用于操纵钢索的不锈钢带眼的钢索端头 尺寸和负荷.第1版》.pdf（6页珍藏版）》请在麦多课文档分享上搜索。

1、AECMA PREN2358 85 1012311 00075Ll2 5 -: A.E.C.M.A. STANDARD prEN2358 NORME A.E.C.M.A. Edition I A.E.C.M.A. NORM February 1985 . rn 2 2 (D rn Iu t- I i !i? a a W O O ln r- iu -2 r x: 3 L - - O n m: CU I J 0 c- a O a a % a 2 ui C v: u1 J u1 5 5 s a d F z 0: C U z z u ; U z I- c C s - 8 ? - O d O u C r

2、 u o UDC : 629.7.05 : 621.854 : 621.85.052.004.1 Key words : Aircraft industry, flight control, flexible cable, cable end, crimping end piece, dimensions, breaking loads. ENGLISH VERSION Aerospace series Eye-ends in corrosion resisting steel swaged on type, control cable Dimensions and loads Srie ar

3、ospatiale Embouts il en acier rsistant la corrosion sertir sur cbles de commandes Dimensions et charges Luft- und Raumfahrt Seilschuhe mit se aus korrosionsbestndigem Stahl zum Aufquetschen auf Steuerseile Mae und Belastungen This industrial standard for the aerospace sector has been drawn up under

4、the responsibility of AECMA (Association Europenne des Constructeurs de Matriel Arospatial). It is published on yellow paper in three equivalent versions (English, French, German). It will be submitted to CEN (European Committee for Standardization) as a draft European Standard. I I Approved by The

5、equivalent versions in French and German languages COMIT DE NORMALISATION can be supplied by B.N.A.E., 8, rue Moreau-Vauthier of A.E.C.M.A. 1984-09-07 92100 BOULOGNE-BILLANCOURT - FRANCE. Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AEC

6、MANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Contents 1 2 References 3 Material and surface treatment 4 Required characteristics 5 Designation 6 Marking 7 Technical specification Scope and field of application Copyright Association Europeene des Constructeurs

7、de Materiel Aerospatial Provided by IHS under license with AECMANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AECMA PREN2358 85 = LOL23LL 0007544 9 m prEN2358 Page 3 1 Scope and field of application This standard specifies the characteristics of corrosion resisti

8、ng steel eye-ends suitable for swaging on to aircraft control cables, 2 References IS0 2020 - 1984, Aerospace - Mechanical system parts - Preformed flexible steel wire rope for aircraft controls - Technical specification EN2465 EN25 16 , Passivation of corrosion resisting steels 1) EN2569 , Steel FE

9、-PA 11 - Softened - Bars De 100 mm Control cable fittings and turnbarrel assemblies - Technical Specification i) . 3 Material and surface treatment 3.1 Material Steel EN2465. 3.2 Surface treatment Passivation EN2516 1). . 4 Required charactkisticc 4.1 Dimensions - Tolerances - Loads - Mass 8 The con

10、figuration shall correspond to figure and the dimensions shall conform to the values given in the figure and the table. 4.2 Surface roughness See figure. 1) In preparation Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMANot for Resale

11、No reproduction or networking permitted without license from IHS-,-,-AECMA PREN2358 85 m LOL23LL 0007545 O = prEN2358 Page 4 O r - OZT 1 l- L a m U .- Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMANot for ResaleNo reproduction or ne

12、tworking permitted without license from IHS-,-,- AECMA PREN2358 85 10L231L O007546 2 prEN2358 Page 5 o a C .- in S O in C .- .- E Q + o + m CO - o 0- U m N a. O- + N c 0- + - Co e x U “; L uc 7 N x - m N u.5 + O Co n + Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provide

13、d by IHS under license with AECMANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AECMA PREN2358 85 LOL2311 0007547 4 I prEK2358 Page 6 5 Designation Each eye-end for swaging on to cables shall only be designated as in the f oiiowing example : Description block CABL

14、E EYE-END Identity block EN 358-. T- Number of EN standard 1 56 = Cable code, see table Note : If necessary, originator code 59005 may be introduced between the description block and identity block. G Marking In addition to the manufacturers own marking, each eye-end for swaging on to cables shall b

15、e marked (see figure) using the identity block as defined in clause 5 of this standard. The marking method is at the manufacturers option. 7 Technical specification The eye-ends for swaging on to cables supplied according to this standard shall conform with the requirements of EN2569 1). 1) In preparation. Copyright Association Europeene des Constructeurs de Materiel Aerospatial Provided by IHS under license with AECMANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-