BS ISO IEC 18328-2-2015 Identification cards ICC-managed devices Physical characteristics and test methods for cards with devices《识别卡 集成电路卡管理设备 卡与设备的物理特性和测试方法》.pdf

《BS ISO IEC 18328-2-2015 Identification cards ICC-managed devices Physical characteristics and test methods for cards with devices《识别卡 集成电路卡管理设备 卡与设备的物理特性和测试方法》.pdf》由会员分享，可在线阅读，更多相关《BS ISO IEC 18328-2-2015 Identification cards ICC-managed devices Physical characteristics and test methods for cards with devices《识别卡 集成电路卡管理设备 卡与设备的物理特性和测试方法》.pdf（22页珍藏版）》请在麦多课文档分享上搜索。

1、BSI Standards Publication BS ISO/IEC 18328-2:2015 Identification cards ICC- managed devices Part 2: Physical characteristics and test methods for cards with devicesBS ISO/IEC 18328-2:2015 BRITISH STANDARD National foreword This British Standard is the UK implementation of ISO/IEC 18328-2:2015. The U

2、K participation in its preparation was entrusted to Technical Committee IST/17, Cards and personal identification. A list of organizations represented on this committee can be obtained on request to its secretary. This publication does not purport to include all the necessary provisions of a contrac

3、t. Users are responsible for its correct application. The British Standards Institution 2015. Published by BSI Standards Limited 2015 ISBN 978 0 580 83854 5 ICS 35.240.15 Compliance with a British Standard cannot confer immunity from legal obligations. This British Standard was published under the a

4、uthority of the Standards Policy and Strategy Committee on 30 November 2015. Amendments/corrigenda issued since publication Date T e x t a f f e c t e dBS ISO/IEC 18328-2:2015 Identification cards ICC-managed devices Part 2: Physical characteristics and test methods for cards with devices Cartes did

5、entification Dispositifs contrls par carte circuit intgr (ICC) Partie 2: Caractristiques physiques et mthodes dessai des cartes avec les dispositifs INTERNATIONAL STANDARD ISO/IEC 18328-2 Reference number ISO/IEC 18328-2:2015(E) First edition 2015-11-01 ISO/IEC 2015 BS ISO/IEC 18328-2:2015ii ISO/IEC

6、 2015 All rights reserved COPYRIGHT PROTECTED DOCUMENT ISO/IEC 2015, Published in Switzerland All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting

7、 on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Ch. de Blandonnet 8 CP 401 CH-1214 Vernier, Geneva, Switzerland Tel. +41 22 749 01 11 Fax +41

8、22 749 09 47 copyrightiso.org www.iso.org ISO/IEC 18328-2:2015(E)BS ISO/IEC 18328-2:2015ISO/IEC 18328-2:2015(E)Foreword iv 1 Scope .1 2 Normative references 1 3 Terms and definitions .1 4 Abbreviated terms 2 5 Requirements 2 5.1 General requirements . 2 5.1.1 Integrated circuit cards (ICCs) . 2 5.1.

9、2 ICCs with contacts . 2 5.1.3 Contactless ICCs 2 5.2 Requirements for ICCs containing displays . 3 5.2.1 General requirements 3 5.2.2 Requirements for matrix displays 3 5.2.3 Requirements for segmented displays 3 5.3 Requirements for cards containing biometric capture devices 3 Annex A (informative

10、) ID-T size card .4 Annex B (informative) Coexistence of new devices with existing technologies 6 Annex C (informative) Display and input element technologies 11 Bibliography .13 ISO/IEC 2015 All rights reserved iii Contents PageBS ISO/IEC 18328-2:2015ISO/IEC 18328-2:2015(E) Foreword ISO (the Intern

11、ational Organization for Standardization) and IEC (the International Electrotechnical Commission) form the specialized system for worldwide standardization. National bodies that are members of ISO or IEC participate in the development of International Standards through technical committees establish

12、ed by the respective organization to deal with particular fields of technical activity. ISO and IEC technical committees collaborate in fields of mutual interest. Other international organizations, governmental and non-governmental, in liaison with ISO and IEC, also take part in the work. In the fie

13、ld of information technology, ISO and IEC have established a joint technical committee, ISO/IEC JTC 1. The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for

14、 the different types of document should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives). Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO

15、 and IEC shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received (see www.iso.org/patents). Any trade name used in th

16、is document is information given for the convenience of users and does not constitute an endorsement. For an explanation on the meaning of ISO specific terms and expressions related to conformity assessment, as well as information about ISOs adherence to the WTO principles in the Technical Barriers

17、to Trade (TBT) see the following URL: Foreword - Supplementary information The committee responsible for this document is ISO/IEC JTC 1, Information technology, SC 17, Cards and personal identification. ISO/IEC 18328 consists of the following parts, under the general title Identification cards ICC-

18、managed devices: Part 1: General framework Part 2: Physical characteristics and test methods for cards with devices Part 3: Organization, security and commands for interchangeiv ISO/IEC 2015 All rights reservedBS ISO/IEC 18328-2:2015INTERNATIONAL ST ANDARD ISO/IEC 18328-2:2015(E) Identification card

19、s ICC-managed devices Part 2: Physical characteristics and test methods for cards with devices 1 Scope This part of ISO/IEC 18328 defines physical characteristics and test methods for cards with devices, including but not limited to power supplying devices, displays, sensors, microphones, loudspeake

20、rs, buttons or keypads. This part of ISO/IEC 18328 also covers aspects of coexistence of technologies of devices on the card and other machine readable card technologies. Additional requirements related to biometric capture devices are defined in ISO/IEC 17839-2. Such requirements may be applied in

21、addition to the ones defined in this part of ISO/IEC 18328. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the la

22、test edition of the referenced document (including any amendments) applies. ISO/IEC 7810, Identification cards Physical characteristics ISO/IEC 7816-1, Identification cards Integrated circuit cards Part 1: Cards with contacts Physical characteristics ISO/IEC 14443-1, Identification cards Contactless

23、 integrated circuit cards Proximity cards Part 1: Physical characteristics ISO/IEC 17839-2 1) , Identification cards Biometric system on card Part 2: Physical characteristics ISO/IEC 18328-1 1) , Identification cards ICC-managed devices Part 1: General framework 3 Terms and definitions For the purpo

24、ses of this document, the terms and definitions given in ISO/IEC 7810, ISO/IEC 18328-1 and the following apply. 3.1 active display area area of the display that has active dots or segments Note 1 to entry: The total display area typically extends beyond the active display area. 3.2 zone 1total displ

25、ay area excluding the active display area 1) To be published. ISO/IEC 2015 All rights reserved 1BS ISO/IEC 18328-2:2015ISO/IEC 18328-2:2015(E) 3.2.2 zone 2active display area 4 Abbreviated terms LED Light-emitting diode OLED Organic light-emitting diode 5 Requirements 5.1 General requirements 5.1.1

26、Integrated circuit cards (ICCs) ICCs with integrated devices shall comply with the requirements defined for ID-1 cards as specified in ISO/IEC 7810, in particular regarding the following: card dimensions and tolerances; bending stiffness; peel strength; overall card warpage; card dimensional stabili

27、ty and warpage with temperature and humidity; resistance to chemicals; opacity. Guidance about the co-existence of different technologies on such cards is given in Annex B. A description of different display and input element technologies is provided in Annex C. 5.1.2 ICCs with contacts ICCs with co

28、ntacts shall in addition meet the requirements specified in ISO/IEC 7816-1 regarding the following: mechanical strength; electrical resistance of contacts; electromagnetic interference. 5.1.3 Contactless ICCs Contactless ICCs shall in addition meet the requirement specified in ISO/IEC 14443-1 regard

29、ing the antenna location.2 ISO/IEC 2015 All rights reservedBS ISO/IEC 18328-2:2015ISO/IEC 18328-2:2015(E) 5.2 Requirements for ICCs containing displays 5.2.1 General requirements The following requirements apply to ICCs containing electronic displays. NOTE 1 Today, there is no stable state-of-the-ar

30、t regarding the technology of card displays or the correlation between legibility of displays and their functional performance. The requirements described in this part of ISO/IEC 18328 should be considered as preliminary. The detailed requirements for ICCs containing electronic displays depend on th

31、e specific use-case. ICCs containing electronic displays meet the test requirements if the optical contrast is not less than a defined percentage of the optical contrast immediately before the test, as specified by the application. NOTE 2 Readability and contrast: An observers ability to perceive th

32、e information from an electronic display depends on two major factors. These are (a) size and font of the displayed information in relationship to the viewing position and (b) the optical contrast of the displayed information to the surrounding environment. Optical contrast is the comparison of the

33、brightness or sterance of the display to the brightness of the surrounding environment. High readability results by optimizing specific contrast ratios. 5.2.2 Requirements for matrix displays In addition to the test requirements in 5.2.1, for ICCs with matrix displays, it is required that not less t

34、han a defined percentage of all pixels remain functional after the test, as specified by the application. 5.2.3 Requirements for segmented displays In addition to the test requirements in 5.2.1, for ICCs with segmented displays, no segment failure (dead segment) is allowed, i.e. after the test all s

35、egments should be working in both directions from white to black and from black to white. Dead spots in zone 1 (i.e. outside the active display area) can be accepted. Dead spots in zone 2 (i.e. within the active display area) can be accepted if their size and number are lower than values specified b

36、y the application. 5.3 Requirements for cards containing biometric capture devices ICCs that embed a biometric capture device may be required to conform to requirements in ISO/IEC 17839-2, in addition to the mandatory requirements of this part of ISO/IEC 18328. Annex A gives an example of an alterna

37、tive card size. ISO/IEC 2015 All rights reserved 3BS ISO/IEC 18328-2:2015ISO/IEC 18328-2:2015(E) Annex A (informative) ID-T size card A.1 General ID-T size cards are the same length and width as a normal ID-1 size card but are thicker. The additional thickness is required for an interim period of ti

38、me to accommodate electronic card components used for biometric capture devices. This card format is intended to accommodate certain restrictions of current manufacturing technology. The need for this Annex will be reviewed as part of the next revision of this part of ISO/IEC 18328. ID-T size cards

39、are not intended for use with any type of insertion reader typically used with an ID-1 size card such as for magnetic stripe or ICC contact readers. This Annex specifies physical characteristics for a thicker card if it is used. A.2 Conformance ID-T size cards are made from similar materials as ID-1

40、 size cards and meet all requirements given in ISO/IEC 7810 for ID-1 size cards except as noted in this Annex. NOTE Dynamic bending stress and dynamic torsional stress in ISO/IEC 7810 apply only to ID-1 size cards. A.3 Terms and definitions A.3.1 ID-T nominally 85,60 mm (3,370 in) wide by 53,98 mm (

41、2,125 in) high by 2,5 mm (0,098 in) thick A.4 Dimensions Dimensions a, b and c (see Figure A.1) shall be as defined for an ID-1 size card. Dimension d shall be 2,5 0,2 mm. Dimension e (optional radius all around the perimeter of the card). NOTE The addition of an optional 0,3 0,1 mm radius, e, is re

42、commended. Adding such a radius will make it easier to slide this thicker card into a wallet card holder.4 ISO/IEC 2015 All rights reservedBS ISO/IEC 18328-2:2015ISO/IEC 18328-2:2015(E) d c a b 1 2 e( optional) Key 1 top reference edge 2 left edge Figure A.1 ID-T size card dimensions A.5 Bending sti

43、ffness The bending stiffness of the ID-T size card shall be such that deformations in normal use (bends not creases) can be removed by the recording or printing device without impairing the function of the card. The deformation which occurs when the card is subjected to the test load as described in

44、 ISO/IEC 10373-1 shall be 4 mm (0,157 in) maximum. The card shall return to within 0,3 mm (0,012 in) of its original flat condition within one minute after the load is removed. A.6 Overall card warpage The maximum distance from a flat rigid plate to any portion of the convex surface of an ID-T size

45、card shall not be greater than 3,2 mm (0,126 in) including the card thickness. ISO/IEC 2015 All rights reserved 5BS ISO/IEC 18328-2:2015ISO/IEC 18328-2:2015(E) Annex B (informative) Coexistence of new devices with existing technologies B.1 General This informative Annex defines the conditions under

46、which new devices can coexist with other machine readable card technologies. B.2 References For the purposes of this Annex, the following references apply. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amend

47、ments) applies. ISO/IEC 7810, Identification cards Physical characteristics ISO/IEC 7811-1, Identification cards Recording technique Part 1: Embossing ISO/IEC 7811-2, Identification cards Recording technique Part 2: Magnetic stripe Low coercivity ISO/IEC 7811-6, Identification cards Recording techni

48、que Part 6: Magnetic stripe High coercivity ISO/IEC 7811-7, Identification cards Recording technique Part 7: Magnetic stripe High coercivity, high density ISO/IEC 7811-8, Identification cards Recording technique Part 8: Magnetic stripe Coercivity of 51,7 kA/m (650 Oe) ISO/IEC 7811-9, Identification

49、cards Recording technique Part 9: Tactile identifier mark ISO/IEC 7816-1, Identification cards Integrated circuit cards Part 1: Cards with contacts Physical characteristics ISO/IEC 7816-2, Identification cards Integrated circuit cards Part 2: Cards with contacts Dimensions and location of the contacts ISO/IEC 11693-1, Identification cards Optical memory cards Part 1: General c