BS ISO 9657-2004 Pliers and nippers for electronics - General technical requirements《电讯夹扭钳和剪切钳 通用技术要求》.pdf

《BS ISO 9657-2004 Pliers and nippers for electronics - General technical requirements《电讯夹扭钳和剪切钳 通用技术要求》.pdf》由会员分享，可在线阅读，更多相关《BS ISO 9657-2004 Pliers and nippers for electronics - General technical requirements《电讯夹扭钳和剪切钳 通用技术要求》.pdf（10页珍藏版）》请在麦多课文档分享上搜索。

1、BRITISH STANDARD BS ISO 9657:2004 Pliers and nippers for electronics General technical requirements ICS 25.140.30 BS ISO 9657:2004 This British Standard was published under the authority of the Standards Policy and Strategy Committee on 9 December 2004 BSI 9 December 2004 ISBN 0 580 45034 1 National

2、 foreword This British Standard reproduces verbatim ISO 9657:2004 and implements it as the UK national standard. It supersedes BS 7330-2:1990, which is withdrawn. The UK participation in its preparation was entrusted by Technical Committee MTE/15, Hand tools, to Subcommittee MTE/15/13, Assembly tool

3、s for screws and nuts, pliers and nippers, which has the responsibility to: A list of organizations represented on this subcommittee can be obtained on request to its secretary. Cross-references The British Standards which implement international publications referred to in this document may be foun

4、d in the BSI Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Search” facility of the BSI Electronic Catalogue or of British Standards Online. This publication does not purport to include all the necessary provisions of a contract. Users are respo

5、nsible for its correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. aid enquirers to understand the text; present to the responsible international/European committee any enquiries on the interpretation, or proposals for change, and keep t

6、he UK interests informed; monitor related international and European developments and promulgate them in the UK. Summary of pages This document comprises a front cover, an inside front cover, the ISO title page, pages ii and iii, a blank page, pages 1 to 3 and a back cover. The BSI copyright date di

7、splayed in this document indicates when the document was last issued. Amendments issued since publication Amd. No. Date Comments Reference number ISO 9657:2004(E)INTERNATIONAL STANDARD ISO 9756 ceSond deition -400251-90 Pliers and nippers for electronics General technical requirements Pinces pour ll

8、ectronique Spcifications techniques gnrales Referecne unbmer OSI :7569)E(4002INTERNATIONAL STANDARD ISO 9657 Second edition 2004-09-15 dna sreilP ele rof sreppininortc sc reneGacet lcinhaeriuqer lnemts cniPse ruop llcertnouqi e pScficiitasno cethqineus rngalse BSISO9657:2004IS:7569 O4002(E) DPlcsid

9、Fremia ihTs PDF file may ctnoian emdebt dedyfepcaes. In ccaocnadrw eith Aebods licensilop gnic,y this file mairp eb ynted iv roweb detu slahl ton ide ebtlnu deess the typefaces whice era hml era deddebicsnede to i dnanstlaled t noeh computfrep reormign tide ehtin.g In wodlnidaot gnhis file, trapise

10、atpecc tiereht nser ehnopsiiblity fo not infriigngn Aebods licensilop gnic.y ehT ISO tneClar Secrteiraat caceptl on siibality in this .aera Ai ebods a tredamafo kr Aebod SystemI sncotaropr.de teDails fo teh softwacudorp erts sut deo crtaee this PDF file cna f ebi dnuon tlareneG eh Info leratit evo t

11、he file; tP ehDc-Frtaeion marapterew setpo erimizde for irpnti.gn Evyre caer neeb sah taken to sneeru that the file is suitlbae fosu re yb ISO memdob rebeis. In tlnu ehikletneve y ttah lborp aem leratit gno it is f,dnuo plsaee inform ttneC ehlar Secrteiraat ta the serddaig sleb nevwo. ii BSISO9657:2

12、004 iiiForeword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for wh

13、ich a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all

14、matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are ci

15、rculated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held respo

16、nsible for identifying any or all such patent rights. ISO 9657 was prepared by Technical Committee ISO/TC 29, Small tools, Subcommittee SC 10, Assembly tools for screws and nuts, pliers and nippers. This second edition cancels and replaces the first edition (ISO 9657:1989), which has been technicall

17、y revised. BSISO9657:2004BSISO9657:2004INTENRATIONAL TSANDADR IS:7569 O4002(E)1Pliers and nippers for electronics General technical requirements 1 Scope This International Standard specifies the general technical requirements to be met by pliers and nippers for use in electronics. These pliers and n

18、ippers are intended for use on electronic components, printed circuit boards, etc. NOTE Certain terms used in this International Standard are defined in ISO 8979. This International Standard does not apply to tools intended for working on live electrical circuits and for antistatic applications. 2 N

19、ormative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 8979, Pliers and nippers

20、for electronics Nomenclature 3 Handles The hardness of the handles shall be 40 HRC. The handles shall be shaped and equipped with sleeves to afford a comfortable grip. The width of the handles shall include the thickness of the comfort grip. 4 Heads 4.1 General Unless otherwise specified, the minimu

21、m hardness of the head shall be 40 HRC. 4.2 Joint The joint shall be constructed to allow free movement from the closed to the open position within the normal working range and shall be free from excessive side movement which could impair the function of the tool. 4.3 Jaws Unless otherwise specified

22、 in the dimensional standards, the jaws of all pliers shall meet at the point. Cutting nippers shall have a minimum cutting edge hardness of 55 HRC. Gripping pliers shall have a minimum hardness of 40 HRC on the gripping surfaces. No hardness values are specified for the jaws of round nose pliers. B

23、SISO9657:20042 5 Designation 5.1 Cutting nippers The principal information required for the designation of cutting nippers shall be given in the following order and in accordance with ISO 8979: a) designation and number of nomenclature; b) number of ISO standard concerned; c) dimensions; d) directio

24、n and position of cutting edges; e) type and shape of cutting edges; f) type of joint; g) field of application; e.g. size and type of wire, off-cut retention (only if required for better understanding). 5.2 Single-purpose and multi-purpose pliers The principal information required for the designatio

25、n of single-purpose and multi-purpose pliers shall be given in the following order and in accordance with ISO 8979: a) designation and number of nomenclature; b) number of ISO Standard concerned; c) dimensions; d) shape of the nose (end view at the point); e) shape of the nose (in the longitudinal d

26、irection); f) type of joint; g) whether the jaws are serrated; h) whether the jaws have grooves. For multi-purpose pliers with cutters, the following information shall also be given: i) direction and position of cutting edges; j) type and shape of cutting edges; k) field of application; e.g. size an

27、d type of wire, off-cut retention (only if required for better understanding). 6 Marking Pliers shall be marked with at least the name or trademark of the manufacturer (or responsible supplier). BSISO9657:2004 3Bibliography 1 ISO 6508-1, Metallic materials Rockwell hardness test Part 1: Test method

28、(scales A, B, C, D, E, F, G, H, K, N, T) 2 ISO 9656, Pliers and nippers for electronics Test methods BSISO9657:2004BS ISO 9657:2004 BSI 389 Chiswick High Road London W4 4AL BSI British Standards Institution BSI is the independent national body responsible for preparing British Standards. It presents

29、 the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions British Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to

30、 improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: +44 (0)20 8996

31、9000. Fax: +44 (0)20 8996 7400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer S

32、ervices. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 8996 7001. Email: ordersbsi-. Standards are also available from the BSI website at http:/www.bsi-. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Stand

33、ards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on

34、all its products and services. Contact the Information Centre. Tel: +44 (0)20 8996 7111. Fax: +44 (0)20 8996 7048. Email: infobsi-. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these an

35、d other benefits contact Membership Administration. Tel: +44 (0)20 8996 7002. Fax: +44 (0)20 8996 7001. Email: membershipbsi-. Information regarding online access to British Standards via British Standards Online can be found at http:/www.bsi- Further information about BSI is available on the BSI we

36、bsite at http:/www.bsi-. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a ret

37、rieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. Details and advice can be obtained from the Copyright & Licensing Manager. Tel: +44 (0)20 8996 7070. Fax: +44 (0)20 8996 7553. Email: copyrightbsi-.