BS ISO 7507-4-2010 en_9982 Petroleum and liquid petroleum products - Calibration of vertical cylindrical tanks - Internal electro-optical distance-ranging method《石油和液态石油产品.直立式圆.pdf

《BS ISO 7507-4-2010 en_9982 Petroleum and liquid petroleum products - Calibration of vertical cylindrical tanks - Internal electro-optical distance-ranging method《石油和液态石油产品.直立式圆.pdf》由会员分享，可在线阅读，更多相关《BS ISO 7507-4-2010 en_9982 Petroleum and liquid petroleum products - Calibration of vertical cylindrical tanks - Internal electro-optical distance-ranging method《石油和液态石油产品.直立式圆.pdf（30页珍藏版）》请在麦多课文档分享上搜索。

1、BS ISO 7507-4:2010 ICS 75.180.30 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW BRITISH STANDARD Petroleum and liquid petroleum products Calibration of vertical cylindrical tanks Part 4: Internal electro-optical distance-ranging methodThis British Standard was published under

2、 the authority of the Standards Policy and Strategy Committee on 31 March 2010. BSI 2010 ISBN 978 0 580 69280 2 Amendments/corrigenda issued since publication Date Comments BS ISO 7507-4:2010 National foreword This British Standard is the UK implementation of ISO 7507-4:2010. It supersedes BS 7723-4

3、:1995 which is withdrawn. The UK participation in its preparation was entrusted to Technical Committee PTI/12, Petroleum Measurement and Sampling. A list of organizations represented on this committee can be obtained on request to its secretary. This publication does not purport to include all the n

4、ecessary provisions of a contract. Users are responsible for its correct application. Compliance with a British Standard cannot confer immunity from legal obligations.BS ISO 7507-4:2010Reference number ISO 7507-4:2010(E) ISO 2010INTERNATIONAL STANDARD ISO 7507-4 Second edition 2010-02-01 Petroleum a

5、nd liquid petroleum products Calibration of vertical cylindrical tanks Part 4: Internal electro-optical distance-ranging method Ptrole et produits ptroliers liquides Jaugeage des rservoirs cylindriques verticaux Partie 4: Mthode par mesurage lectro-optique interne de la distance BS ISO 7507-4:2010 I

6、SO 7507-4:2010(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobes licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downl

7、oading this file, parties accept therein the responsibility of not infringing Adobes licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the

8、General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address g

9、iven below. COPYRIGHT PROTECTED DOCUMENT ISO 2010 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at t

10、he address below or ISOs member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in Switzerland ii ISO 2010 All rights reservedBS ISO 7507-4:2010 ISO 7507-4:2010

11、(E) ISO 2010 All rights reserved iiiContents Page Foreword iv 1 Scope1 2 Normative references1 3 Terms and definitions .1 4 Precautions 2 5 Equipment 2 6 General considerations.3 7 EODR instrument set-up within the tank 4 8 Selection of target points .4 9 Calibration procedure .5 10 Other measuremen

12、ts.7 11 Calculation and development of capacity tables .7 Annex A (normative) Procedure for verifying EODR instruments.8 Annex B (normative) Calculation of internal radii from the measured parameters.11 Annex C (informative) Calibration uncertainties12 Bibliography20 BS ISO 7507-4:2010 ISO 7507-4:20

13、10(E) iv ISO 2010 All rights reservedForeword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body

14、interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotech

15、nical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by t

16、he technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent right

17、s. ISO shall not be held responsible for identifying any or all such patent rights. ISO 7507-4 was prepared by Technical Committee ISO/TC 28, Petroleum products and lubricants, Subcommittee SC 2, Measurement of petroleum and related products. This second edition cancels and replaces the first editio

18、n (ISO 7507-4:1995), which has been technically revised. ISO 7507 consists of the following parts, under the general title Petroleum and liquid petroleum products Calibration of vertical cylindrical tanks: Part 1: Strapping method Part 2: Optical-reference-line method Part 3: Optical-triangulation m

19、ethod Part 4: Internal electro-optical distance-ranging method Part 5: External electro-optical distance-ranging method BS ISO 7507-4:2010 INTERNATIONAL STANDARD ISO 7507-4:2010(E) ISO 2010 All rights reserved 1Petroleum and liquid petroleum products Calibration of vertical cylindrical tanks Part 4:

20、 Internal electro-optical distance-ranging method 1 Scope This part of ISO 7507 specifies a method for the calibration of vertical cylindrical tanks having diameters greater than 5 m by means of internal measurements using an electro-optical distance-ranging (EODR) instrument, and for the subsequent

21、 compilation of tank capacity tables. The method is suitable for tanks tilted up to a 3 % deviation from the vertical, provided that a correction is applied for the measured tilt as described in ISO 7507-1:2003, Clause 11. This part of ISO 7507 also applies to tanks with floating roofs or internal f

22、loating blankets. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 7507

23、-1:2003, Petroleum and liquid petroleum products Calibration of vertical cylindrical tanks Part 1: Strapping method IEC 60825-1:2007, Safety of laser products Part 1: Equipment classification and requirements 3 Terms and definitions For the purposes of this document, the terms and definitions given

24、in ISO 7507-1 and the following apply. 3.1 reference target point fixed point clearly marked on a fixed point within the tank, e.g. on the inside surface of the tank shell wall 3.2 slope distance distance measured from the electro-optical distance-ranging instrument to a target point on any given co

25、urse of the tank shell wall 3.3 target point one of a series of points on the inside surface of the tank shell wall to which slope distance, and vertical and horizontal angles are measured by use of the electro-optical ranging instrument BS ISO 7507-4:2010 ISO 7507-4:2010(E) 2 ISO 2010 All rights re

26、served4 Precautions The general precautions and safety precautions specified in ISO 7507-1 shall apply to this part of ISO 7507. In addition, the inside of the tank shall be clean. The laser beam emitted by the distance-ranging unit shall conform to IEC 60825-1. 5 Equipment 5.1 Electro-optical dista

27、nce-ranging instrument To achieve uncertainties of tank volumes acceptable in legal metrology, the angular measuring part of the instrument should have an angular graduation and resolution equal to or better than 3,142 10 6rad 0,2 mgon 1) and the distance-measuring part of the instrument, used for d

28、irect determination of distances, should have a graduation and resolution equal to or better than 1 mm. NOTE For analysis of the impact of uncertainty of the equipment on the uncertainty of the calibration table, refer to the examples in Annex C. The accuracy of EODR equipment can be affected by var

29、iations of temperature. The manufacturers guidance should be followed. 5.2 Instrument mounting Instrument mounting shall be firm and stable. If a tripod is used, its legs shall be held firm, and steadied, by suitable devices such as magnetic bearers or an equivalent system. On floating-roof tanks or

30、 tanks with internal floating blankets, the supports of the EODR instrument should preferably rest on the tank bottom, while access to the instrument is through the roof or the blanket (see Figure 1). If this is not possible, mounting directly on the floating roof or blanket can be possible, but onl

31、y if the stability of the instrument during the calibration procedure can be guaranteed. Key 1 EODR instrument 2 floating roof 3 tank bottom Figure 1 EODR installation on floating roof 1) 2 radians = 400 000 mgon. BS ISO 7507-4:2010 ISO 7507-4:2010(E) ISO 2010 All rights reserved 3EODR measurements

32、are restricted by a) minimum measurable distance; b) minimum incidence angle that still gives expected measurement uncertainty. These limits are normally provided by the EODR equipment manufacturer. If, for the given shape of the tank (height and diameter), the limits of incidence angles given by th

33、e manufacturer cannot be met from one position, either a higher uncertainty shall be accepted or the EODR equipment shall be placed in several positions. If this is not possible, this method might not be suitable for the given application. NOTE Integration of measurements from multiple positions of

34、the EODR, if required, is usually performed using procedures published by the instrument manufacturer. There are no standard calculations and, therefore, this part of ISO 7507 does not include equations for this case. 5.3 Laser beam emitter The laser beam emitter used to position target points on th

35、e tank shell shall be either an integral part of the EODR instrument or a separate device whose axis is parallel to the axis of the EODR instrument. 5.4 Stadia Stadia shall be a bar at least 2 m long with two marks. The graduated length between these marks shall be calibrated. Extended calibration u

36、ncertainty should be of the order of 0,05 mm. The stadia shall be made of a material whose thermal expansion is known. 5.5 Equipment for bottom calibration Equipment for calibration of the tank bottom shall be as specified in ISO 7507-1:2003, Clause 10. 5.6 Auxiliary equipment Auxiliary equipment sh

37、all include devices to steady the EODR unit, lighting, etc. 6 General considerations 6.1 The EODR instrument shall be maintained so that its performance can be traced to national and/or international measurement standards. The accuracy of the angular measuring unit shall be verified using the proced

38、ures described in Annex A. The distance-measuring unit is expected to hold its calibration and it is not normally necessary to verify it in the field. If verification is performed, the procedure given in Annex A shall be followed. 6.2 Tanks shall be calibrated only after they have been filled at lea

39、st once with a liquid of density equal to or greater than that of the liquid that they will hold when in use. NOTE The hydrostatic test applied to new tanks can satisfy this requirement in most cases. 6.3 The tank shall be free from vibration and air-borne dust particles. The floor of the tank shoul

40、d be as free as possible from debris, dust and loose scale. 6.4 Encrustation of the inner walls of the tank should be checked. If the estimated thickness, nature and distribution of the encrustation are deemed unacceptable, the tank should not be calibrated using this method. BS ISO 7507-4:2010 ISO

41、7507-4:2010(E) 4 ISO 2010 All rights reserved6.5 Lighting, when required, shall be placed within the tank so as not to interfere with the operation of the EODR instrument. 6.6 Calibration should be carried out without interruption. 7 EODR instrument set-up within the tank 7.1 The instrument shall be

42、 set up with care, in accordance with the procedure and instructions given by the manufacturer. 7.2 The instrument shall be set up so as to be stable. If necessary, the tank bottom in the vicinity of the instrument shall be made firm and steady by placing heavy weights in the area. The legs of the t

43、ripod on which the instrument is mounted shall be steadied by use of suitable devices, such as magnetic bearers, to prevent slippage on the tank bottom. 7.3 The instrument should be located at, or near, the centre of the tank to ensure that the measured slope distances, at any one horizontal level,

44、do not vary significantly and to minimize the overall uncertainty of slope distance determination. NOTE Stability of the EODR instrument is likely to be more important than its position in the centre of the tank. 7.4 The instrument shall be free from external vibration. 7.5 The sighting lines from t

45、he instrument to the tank shell wall shall not be obstructed. 7.6 Select and clearly mark on fixed points inside the tank, e.g. on the shell wall, two reference target points. These should be approximately 1,571 rad (100 gon) apart and as near to the horizontal plane of the instrument as possible. 7

46、.7 At least the minimum settling time recommended by the manufacturer should be allowed before the instrument is used. 7.8 The instrument shall be set horizontal, thus ensuring that the vertical axis (standing axis) is vertical. 8 Selection of target points 8.1 Two sets of target points per course s

47、hall be selected, one at approximately 1/4 of the course height above the lower horizontal seam, the other at approximately 1/4 of the course height below the upper horizontal seam. The number of target points per set on each course of the tank shell wall is dependent on tank circumference. The mini

48、mum number of target points per set as a function of tank circumference shall be in accordance with Table 1, and is illustrated in Figure 2. Where tank walls are deformed, the number of target points can be greater than the minimum given by this part of ISO 7507. 8.2 The target points shall be at le

49、ast 300 mm from any vertical welded seam. BS ISO 7507-4:2010 ISO 7507-4:2010(E) ISO 2010 All rights reserved 5Table 1 Minimum number of target points Tank circumference m Minimum number of points u 50 10 50, u 100 12 100, u 150 16 150, u 200 20 200, u 250 24 250, u 300 30 300 36 A number of target points greater than the minimum number of points in Table 1 may be chosen depending on specific circumstances and tank conditions. Key 1 seam Figure 2 Illustration of target positioning on tank shell wall 9