BS ISO 6482-2017 en_7430 Shipbuilding Deck machinery Warping end profiles《造船 甲板机械 绞缆筒外形》.pdf

《BS ISO 6482-2017 en_7430 Shipbuilding Deck machinery Warping end profiles《造船 甲板机械 绞缆筒外形》.pdf》由会员分享，可在线阅读，更多相关《BS ISO 6482-2017 en_7430 Shipbuilding Deck machinery Warping end profiles《造船 甲板机械 绞缆筒外形》.pdf（14页珍藏版）》请在麦多课文档分享上搜索。

1、Shipbuilding Deck machinery Warping end profiles BS ISO 6482:2017 BSI Standards Publication WB11885_BSI_StandardCovs_2013_AW.indd 1 15/05/2013 15:06 ISO 2017 Shipbuilding Deck machinery Warping end profiles Construction navale Auxiliaires de pont Profils de poupe INTERNATIONAL STANDARD ISO 6482 Seco

2、nd edition 2017-05 Reference number ISO 6482:2017(E) National foreword This British Standard is the UK implementation of ISO 6482:2017. The UK participation in its preparation was entrusted to Technical Committee SME/32, Ships and marine technology - Steering committee. A list of organizations repre

3、sented on this committee can be obtained on request to its secretary. This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2017 Published by BSI Standards Limited 2017 ISBN 978 0

4、580 89811 2 ICS 47.020.50 Compliance with a British Standard cannot confer immunity from legal obligations. This British Standard was published under the authority of the Standards Policy and Strategy Committee on 30 June 2017. Amendments/corrigenda issued since publication Date Text affected BRITIS

5、H STANDARD BS ISO 6482:2017 ISO 2017 Shipbuilding Deck machinery Warping end profiles Construction navale Auxiliaires de pont Profils de poupe INTERNATIONAL STANDARD ISO 6482 Second edition 2017-05 Reference number ISO 6482:2017(E) BS ISO 6482:2017 ISO 6482:2017(E)ii ISO 2017 All rights reserved COP

6、YRIGHT PROTECTED DOCUMENT ISO 2017, Published in Switzerland All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet,

7、without prior written permission. Permission can be requested from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Ch. de Blandonnet 8 CP 401 CH-1214 Vernier, Geneva, Switzerland Tel. +41 22 749 01 11 Fax +41 22 749 09 47 copyrightiso.org www

8、.iso.org BS ISO 6482:2017 ISO 6482:2017(E)ii ISO 2017 All rights reserved COPYRIGHT PROTECTED DOCUMENT ISO 2017, Published in Switzerland All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form or by any means, electronic or me

9、chanical, including photocopying, or posting on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Ch. de Blandonnet 8 CP 401 CH-1214 Vernier, Geneva

10、, Switzerland Tel. +41 22 749 01 11 Fax +41 22 749 09 47 copyrightiso.org www.iso.orgISO 6482:2017(E)Foreword iv 1 Scope . 1 2 Normative references 1 3 Terms and definitions . 1 4 Types, nominal sizes and dimensions 1 4.1 Types 1 4.2 Nominal sizes and dimensions 1 5 Relation between warping end dime

11、nsions and rope sizes 3 5.1 Proportional relation between warping end lengths and selected rope sizes . 3 5.2 Proportional relation between warping end diameters and selected rope sizes 3 6 Calculation of warping end shaft torque and bending moment 3 6.1 Calculated position of maximum torque. 3 6.2

12、Calculated position of bending moment at maximum torque 3 7 Dimensional tolerances and surface roughness 4 8 Designation 4 ISO 2017 All rights reserved iii Contents Page BS ISO 6482:2017 ISO 6482:2017(E) Foreword ISO (the International Organization for Standardization) is a worldwide federation of n

13、ational standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. Inter

14、national organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. The procedures used to develop this document and those int

15、ended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see ww

16、w .iso .org/ directives). Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the development of the docum

17、ent will be in the Introduction and/or on the ISO list of patent declarations received (see www .iso .org/ patents). Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement. For an explanation on the voluntary nature of standards,

18、 the meaning of ISO specific terms and expressions related to conformity assessment, as well as information about ISOs adherence to the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see the following URL: www .iso .org/ iso/ foreword .html. This document was prep

19、ared by ISO/TC 8, Ships and marine technology, Subcommittee SC 4, Outfitting and deck machinery. This second edition cancels and replaces the first edition (ISO 6482:1980), which has been technically revised. This edition revises the type, nominal dimensions, relation between nominal dimensions and

20、rope sizes of warping ends, cancels the part related to hole and rope hooks, and adds some requirements on manufacturing quality.iv ISO 2017 All rights reserved BS ISO 6482:2017 ISO 6482:2017(E) Foreword ISO (the International Organization for Standardization) is a worldwide federation of national s

21、tandards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International

22、organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. The procedures used to develop this document and those intended for

23、 its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .o

24、rg/ directives). Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the development of the document will

25、be in the Introduction and/or on the ISO list of patent declarations received (see www .iso .org/ patents). Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement. For an explanation on the voluntary nature of standards, the mean

26、ing of ISO specific terms and expressions related to conformity assessment, as well as information about ISOs adherence to the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see the following URL: www .iso .org/ iso/ foreword .html. This document was prepared by I

27、SO/TC 8, Ships and marine technology, Subcommittee SC 4, Outfitting and deck machinery. This second edition cancels and replaces the first edition (ISO 6482:1980), which has been technically revised. This edition revises the type, nominal dimensions, relation between nominal dimensions and rope size

28、s of warping ends, cancels the part related to hole and rope hooks, and adds some requirements on manufacturing quality.iv ISO 2017 All rights reserved INTERNATIONAL ST ANDARD ISO 6482:2017(E) Shipbuilding Deck machinery Warping end profiles 1 Scope This document specifies the types, nominal sizes,

29、dimensions, markings and selection rules of warping end profiles. The warping end specified in this document is applicable to windlasses, mooring winches, capstans and other deck machinery with steel wire rope, and ropes of natural and man-made fibre. 2 Normative references The following documents a

30、re referred to in the text in such a way that some or all of their content constitutes requirements of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 8062-3, Geometrica

31、l product specifications (GPS) Dimensional and geometrical tolerances for moulded parts Part 3: General dimensional and geometrical tolerances and machining allowances for castings 3 Terms and definitions For the purposes of this document, the terms and definitions given in ISO 3828 apply. ISO and I

32、EC maintain terminological databases for use in standardization at the following addresses: IEC Electropedia: available at h t t p :/ www .electropedia .org/ ISO Online browsing platform: available at h t t p :/ www .iso .org/ obp 4 Types, nominal sizes and dimensions 4.1 Types The document specifie

33、s two types of warping end profiles, as shown in Figure 1, namely: a) Type C Common; b) Type E Elongated. 4.2 Nominal sizes and dimensions The nominal sizes and physical dimensions of the warping end are given in Figure 1 and Table 1. ISO 2017 All rights reserved 1 BS ISO 6482:2017 ISO 6482:2017(E)

34、Key C Profile type C E Profile type E A Winch side Figure 1 Profile types Table 1 Nominal sizes and physical dimensions Dimensions in millimetres Nominal size D Length of warping end L 1 L 2 R R 1 R 2 C 1 C 2 Type C (L C ) Type E (L E ) 180 180 225 112 45 500 50 25 50 28 200 200 250 125 50 560 56 28

35、 56 32 225 225 280 140 56 630 63 32 63 36 250 250 315 160 63 710 71 36 71 40 280 280 360 180 71 800 80 40 80 45 315 315 400 200 80 900 90 45 90 50 360 360 450 225 90 1 000 100 50 100 56 400 400 500 250 100 1 120 112 56 112 63 450 450 560 280 112 1 250 125 63 125 71 500 500 630 315 125 1 400 140 71 1

36、40 80 560 560 700 360 140 1 600 160 80 160 90 630 630 800 400 160 1 800 180 90 180 100 710 710 900 450 178 2 000 200 100 200 112 800 800 500 2 250 225 112 225 125 900 900 560 2 550 255 128 255 144 1 000 1 000 630 2 850 285 143 285 160 NOTE For the warping end which has special requirements for lengt

37、h, dimensions L C , L Eand L 2may be determined by design engineers or in the contract.2 ISO 2017 All rights reserved BS ISO 6482:2017 ISO 6482:2017(E) Key C Profile type C E Profile type E A Winch side Figure 1 Profile types Table 1 Nominal sizes and physical dimensions Dimensions in millimetres No

38、minal size D Length of warping end L 1 L 2 R R 1 R 2 C 1 C 2 Type C (L C ) Type E (L E ) 180 180 225 112 45 500 50 25 50 28 200 200 250 125 50 560 56 28 56 32 225 225 280 140 56 630 63 32 63 36 250 250 315 160 63 710 71 36 71 40 280 280 360 180 71 800 80 40 80 45 315 315 400 200 80 900 90 45 90 50 3

39、60 360 450 225 90 1 000 100 50 100 56 400 400 500 250 100 1 120 112 56 112 63 450 450 560 280 112 1 250 125 63 125 71 500 500 630 315 125 1 400 140 71 140 80 560 560 700 360 140 1 600 160 80 160 90 630 630 800 400 160 1 800 180 90 180 100 710 710 900 450 178 2 000 200 100 200 112 800 800 500 2 250 2

40、25 112 225 125 900 900 560 2 550 255 128 255 144 1 000 1 000 630 2 850 285 143 285 160 NOTE For the warping end which has special requirements for length, dimensions L C , L Eand L 2may be determined by design engineers or in the contract.2 ISO 2017 All rights reserved ISO 6482:2017(E) 5 Relation be

41、tween warping end dimensions and rope sizes 5.1 Proportional relation between warping end lengths and selected rope sizes The proportional relation between warping end lengths L C , L Eand selected rope diameter d must be met as follows: steel wire rope: Ld 10 natural fibre rope and man-made fibre r

42、ope: Ld 75 , 5.2 Proportional relation between warping end diameters and selected rope sizes The proportional relation between warping end diameter D and selected rope diameter d must be met as follows: steel wire rope: Dd 16 natural fibre rope and man-made fibre rope: Dd 6 6 Calculation of warping

43、end shaft torque and bending moment 6.1 Calculated position of maximum torque The maximum shaft torque shall be calculated with dimension C rgiven by the following formula when calculating the shaft torque of the warping end (see Figure 2). Cd r 07 5 , (1) 6.2 Calculated position of bending moment a

44、t maximum torque The maximum bending moment shall be calculated with dimension L rgiven by the following formula when calculating the bending moment at the maximum shaft torque of the warping end: Ld r 11 7 , (2) Figure 2 Calculating chart of output shaft torque and bending moment of warping end ISO

45、 2017 All rights reserved 3 BS ISO 6482:2017 ISO 6482:2017(E) 7 Dimensional tolerances and surface roughness 7.1 Linear casting dimensional tolerances shall comply with ISO 8062-3 DCTG 11. 7.2 The surface roughness of the warping end shall be determined by design according to the characteristics of

46、ropes and materials of the warping end, or defined in the contract. 8 Designation The warping end profile conforming to this document shall be designated in the following order: EXAMPLE For the designation of a warping end according to ISO 6482, with elongated length and nominal size D = 630 mm: War

47、ping end ISO 6482-0630-L E4 ISO 2017 All rights reserved BS ISO 6482:2017 ISO 6482:2017(E) 7 Dimensional tolerances and surface roughness 7.1 Linear casting dimensional tolerances shall comply with ISO 8062-3 DCTG 11. 7.2 The surface roughness of the warping end shall be determined by design accordi

48、ng to the characteristics of ropes and materials of the warping end, or defined in the contract. 8 Designation The warping end profile conforming to this document shall be designated in the following order: EXAMPLE For the designation of a warping end according to ISO 6482, with elongated length and

49、 nominal size D = 630 mm: Warping end ISO 6482-0630-L E4 ISO 2017 All rights reserved BS ISO 6482:2017 ISO 6482:2017(E) ISO 2017 All rights reserved IC S 47.020.50 Price based on 4 pages BS ISO 6482:2017This page deliberately left blankBSI is the national body responsible for preparing British Standards and other standards-related publications, information and services. BSI is incorporated by Royal Charter. British Standards and other standardization products are pub