BS ISO 6362-2-2014 en_3539 Wrought aluminium and aluminium alloys Extruded rods bars tubes and profiles Mechanical properties《锻造铝和铝合金 挤压杆材 棒材 管材和型材 机械性能》.pdf
《BS ISO 6362-2-2014 en_3539 Wrought aluminium and aluminium alloys Extruded rods bars tubes and profiles Mechanical properties《锻造铝和铝合金 挤压杆材 棒材 管材和型材 机械性能》.pdf》由会员分享,可在线阅读,更多相关《BS ISO 6362-2-2014 en_3539 Wrought aluminium and aluminium alloys Extruded rods bars tubes and profiles Mechanical properties《锻造铝和铝合金 挤压杆材 棒材 管材和型材 机械性能》.pdf(34页珍藏版)》请在麦多课文档分享上搜索。
1、BSI Standards Publication BS ISO 6362-2:2014 Wrought aluminium and aluminium alloys Extruded rods/bars, tubes and profiles Part 2: Mechanical propertiesBS ISO 6362-2:2014 BRITISH STANDARD National foreword This British Standard is the UK implementation of ISO 6362-2:2014. The UK participation in its
2、 preparation was entrusted to Technical Committee NFE/35, Light metals and their alloys. A list of organizations represented on this committee can be obtained on request to its secretary. This publication does not purport to include all the necessary provisions of a contract. Users are responsible f
3、or its correct application. The British Standards Institution 2014. Published by BSI Standards Limited 2014 ISBN 978 0 580 84688 5 ICS 23.040.15; 77.150.10 Compliance with a British Standard cannot confer immunity from legal obligations. This British Standard was published under the authority of the
4、 Standards Policy and Strategy Committee on 30 September 2014. Amendments/corrigenda issued since publication Date Text affected ISO 2014 Wrought aluminium and aluminium alloys Extruded rods/bars, tubes and profiles Part 2: Mechanical properties Aluminium et alliages daluminium corroys Barres, tubes
5、 et profils fils Partie 2: Caractristiques mcaniques INTERNATIONAL STANDARD ISO 6362-2 Fourth edition 2014-09-15 Reference number ISO 6362-2:2014(E)BS ISO 6362-2:2014ISO 6362-2:2014(E)ii ISO 2014 All rights reserved COPYRIGHT PROTECTED DOCUMENT ISO 2014 All rights reserved. Unless otherwise specifie
6、d, no part of this publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below or ISOs
7、member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in SwitzerlandBS ISO 6362-2:2014ISO 6362-2:2014(E) ISO 2014 All rights reserved iii Contents Page Forewor
8、d iv 1 Scope . 1 2 Normative references 1 3 Terms and definitions . 1 4 Tensile testing . 1 5 Mechanical properties 1 Annex A (normative) Rules for rounding 22 Annex B (normative) List of tempers used in Tables 1 to 3 23 Bibliography .25BS ISO 6362-2:2014ISO 6362-2:2014(E) Foreword ISO (the Internat
9、ional Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has bee
10、n established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical stand
11、ardization. The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accorda
12、nce with the editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives). Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details
13、of any patent rights identified during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received (see www.iso.org/patents). Any trade name used in this document is information given for the convenience of users and does not constitute an endor
14、sement. For an explanation on the meaning of ISO specific terms and expressions related to conformity assessment, as well as information about ISOs adherence to the WTO principles in the Technical Barriers to Trade (TBT) see the following URL: Foreword - Supplementary information The committee respo
15、nsible for this document is ISO/TC 79, Light metals and their alloys, Subcommittee SC 6, Wrought aluminium and aluminium alloys. This fourth edition cancels and replaces the third edition (ISO 6362-2:2012), which has been technically revised. ISO 6362 consists of the following parts, under the gener
16、al title Wrought aluminium and aluminium alloys Extruded rods/bars, tubes and profiles: Part 1: Technical conditions for inspection and delivery Part 2: Mechanical properties Part 3: Extruded rectangular bars Tolerances on shape and dimensions Part 4: Profiles Tolerances on shape and dimensions Part
17、 5: Round, square and hexagonal bars Tolerances on shape and dimensions Part 6: Round, square, rectangular and hexagonal tubes Tolerances on shape and dimensions Part 7: Chemical compositioniv ISO 2014 All rights reservedBS ISO 6362-2:2014INTERNATIONAL ST ANDARD ISO 6362-2:2014(E) Wrought aluminium
18、and aluminium alloys Extruded rods/bars, tubes and profiles Part 2: Mechanical properties 1 Scope This part of ISO 6362 specifies the mechanical properties of wrought aluminium and aluminium alloy extruded rods/bars, tubes, and profiles for general engineering applications. It applies to extruded pr
19、oducts. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including a
20、ny amendments) applies. ISO 6362-1, Wrought aluminium and aluminium alloys Extruded rods/bars, tubes and profiles Part 1: Technical conditions for inspection and delivery ISO 6892-1, Metallic materials Tensile testing Part 1: Method of test at room temperature ASTM B557M, Standard Test Methods for T
21、ension Testing Wrought and Cast Aluminum- and Magnesium- Alloy Products 3 Terms and definitions For the purposes of this document, the terms and definitions given in ISO 6362-1 apply. 4 Tensile testing For the selection of the specimens and tensile testing, see ISO 6892-1 or ASTM B557M. 5 Mechanical
22、 properties Values for mechanical properties of aluminium and aluminium alloys are given in Tables 1 to 3. For elongation, two different gauge lengths are used. The choice of the gauge length for elongation measurements (A or A 50mm ) is at the discretion of the producer, unless otherwise agreed. NO
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
5000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- BSISO636222014EN_3539WROUGHTALUMINIUMANDALUMINIUMALLOYSEXTRUDEDRODSBARSTUBESANDPROFILESMECHANICALPROPERTIES
链接地址:http://www.mydoc123.com/p-391127.html