BS ISO 6361-2-2014 en_7859 Wrought aluminium and aluminium alloys Sheets strips and plates Mechanical properties《锻造铝和铝合金 厚板材 薄板材和带材 机械性能》.pdf
《BS ISO 6361-2-2014 en_7859 Wrought aluminium and aluminium alloys Sheets strips and plates Mechanical properties《锻造铝和铝合金 厚板材 薄板材和带材 机械性能》.pdf》由会员分享,可在线阅读,更多相关《BS ISO 6361-2-2014 en_7859 Wrought aluminium and aluminium alloys Sheets strips and plates Mechanical properties《锻造铝和铝合金 厚板材 薄板材和带材 机械性能》.pdf(60页珍藏版)》请在麦多课文档分享上搜索。
1、BSI Standards Publication BS ISO 6361-2:2014 Wrought aluminium and aluminium alloys Sheets, strips and plates Part 2: Mechanical propertiesBS ISO 6361-2:2014 BRITISH STANDARD National foreword This British Standard is the UK implementation of ISO 6361-2:2014. The UK participation in its preparation
2、was entrusted to Technical Committee NFE/35, Light metals and their alloys. A list of organizations represented on this committee can be obtained on request to its secretary. This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correc
3、t application. The British Standards Institution 2014. Published by BSI Standards Limited 2014 ISBN 978 0 580 84725 7 ICS 77.150.10 Compliance with a British Standard cannot confer immunity from legal obligations. This British Standard was published under the authority of the Standards Policy and St
4、rategy Committee on 30 September 2014. Amendments/corrigenda issued since publication Date T e x t a f f e c t e d ISO 2014 Wrought aluminium and aluminium alloys Sheets, strips and plates Part 2: Mechanical properties Aluminium et alliages daluminium corroys Tles, bandes et tles paisses Partie 2: P
5、roprits mcaniques INTERNATIONAL STANDARD ISO 6361-2 Fourth edition 2014-09-15 Reference number ISO 6361-2:2014(E)BS ISO 6361-2:2014ISO 6361-2:2014(E)ii ISO 2014 All rights reserved COPYRIGHT PROTECTED DOCUMENT ISO 2014 All rights reserved. Unless otherwise specified, no part of this publication may
6、be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below or ISOs member body in the country of the r
7、equester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in SwitzerlandBS ISO 6361-2:2014ISO 6361-2:2014(E) ISO 2014 All rights reserved iii Contents Page Foreword iv 1 Scope . 1 2 Normative refere
8、nces 1 3 T erms and definitions . 1 4 Tensile testing . 1 5 Bend testing . 1 6 Mechanical properties 2 6.1 Tensile test 2 6.2 Bend test . 2 Annex A (normative) Rules for rounding results obtained by inspection and testing 50 Bibliography .51BS ISO 6361-2:2014ISO 6361-2:2014(E) Foreword ISO (the Inte
9、rnational Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has
10、 been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical s
11、tandardization. The procedures used to develop this document and those intended for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in acc
12、ordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives). Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Deta
13、ils of any patent rights identified during the development of the document will be in the Introduction and/or on the ISO list of patent declarations received (see www.iso.org/patents). Any trade name used in this document is information given for the convenience of users and does not constitute an e
14、ndorsement. For an explanation on the meaning of ISO specific terms and expressions related to conformity assessment, as well as information about ISOs adherence to the WTO principles in the Technical Barriers to Trade (TBT) see the following URL: Foreword - Supplementary information The committee r
15、esponsible for this document is ISO/TC 79, Light metals and their alloys, Subcommittee SC 6, Wrought aluminium and aluminium alloys. This fourth edition cancels and replaces the third edition (ISO 6361-2:2011), which has been technically revised. ISO 6361 consists of the following parts, under the g
16、eneral title Wrought aluminium and aluminium alloys Sheets, strips and plates: Part 1: Technical conditions for inspection and delivery Part 2: Mechanical properties Part 3: Strips: Tolerances on shape and dimensions Part 4: Sheets and plates: Tolerances on shape and dimensions Part 5: Chemical comp
17、ositioniv ISO 2014 All rights reservedBS ISO 6361-2:2014INTERNATIONAL ST ANDARD ISO 6361-2:2014(E) Wrought aluminium and aluminium alloys Sheets, strips and plates Part 2: Mechanical properties 1 Scope In conjunction with ISO 6361-1, this part of ISO 6361 specifies the mechanical properties of wroug
18、ht aluminium and aluminium alloy sheets, strips, and plates for general engineering applications. It applies to flat-rolled products. The chemical composition of these materials is given in ISO 6361-5. The designations of aluminium and aluminium alloys and the temper designations used in this part o
19、f ISO 6361 are in accordance with ISO 2107. NOTE In certain countries, for purposes of mechanical properties, the thickness limit can be lowered to 0,15 mm by agreement between the purchaser and the supplier, in the case of sheets and strips. 2 Normative references The following documents, in whole
20、or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 6361-1, Wrought aluminium and alumini
21、um alloys Sheets, strips and plates Part 1: Technical conditions for inspection and delivery 3 T erms a nd definiti ons For the purposes of this document, the terms and definitions given in ISO 6361-1 apply. 4 Tensile testing For the selection of the specimens and tensile testing, see ISO 6361-1. 5
22、Bend testing For the selection of the specimens and bend testing, see ISO 6361-1. ISO 2014 All rights reserved 1BS ISO 6361-2:2014ISO 6361-2:2014(E) 6 Mechanical properties 6.1 Tensile test Values for mechanical properties of aluminium and aluminium alloys are given in Tables 1 to 63. For elongation
23、, two different gauge lengths are used. The choice of the gauge length for elongation measurements (A or A 50mm ) is at the discretion of the producer, unless otherwise agreed. NOTE A is the percentage elongation on a gauge length of S . A 50mmis the percentage elongation on a gauge length of 50 mm.
24、 Test results shall be rounded in accordance with the rules given in Annex A. 6.2 Bend test Sheet, strip, and plate shall be capable of being bent cold through an angle of 180, as applicable, around a pin having a radius equal to k times the thickness, t, of the sheet, strip, or plate (for example 0
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- BSISO636122014EN_7859WROUGHTALUMINIUMANDALUMINIUMALLOYSSHEETSSTRIPSANDPLATESMECHANICALPROPERTIES 锻造 铝合金

链接地址:http://www.mydoc123.com/p-391124.html