IEC 60464-3-1-2001 Varnishes used for electrical insulation - Part 3 Specifications for individual materials Sheet 1 Ambient curing finishing varnishes《电气绝缘漆 第3.pdf

《IEC 60464-3-1-2001 Varnishes used for electrical insulation - Part 3 Specifications for individual materials Sheet 1 Ambient curing finishing varnishes《电气绝缘漆 第3.pdf》由会员分享，可在线阅读，更多相关《IEC 60464-3-1-2001 Varnishes used for electrical insulation - Part 3 Specifications for individual materials Sheet 1 Ambient curing finishing varnishes《电气绝缘漆 第3.pdf（24页珍藏版）》请在麦多课文档分享上搜索。

1、INTERNATIONAL STANDARD IEC 60464-3-1 2001 AMENDMENT 1 2006-01 Amendment 1 Varnishes used for electrical insulation - Part 3: Specifications for individual materials - Sheet 1: Ambient curing finishing varnishes O IEC 2006 Droits de reproduction rservs - Copyright - all rights reserved Intemational E

2、lectrotechnical Commission, 3, rue de Varemb, PO Box 131, CH-I211 Geneva 20, Switzerland Telephone: +41 22 919 02 11 Telefax: +41 22 919 03 O0 E-mail: inmailiec.ch Web: www.iec.ch PRICECODE B For price, see current catalogue Commission Electrotechnique Internationale International Electrotechnical C

3、ommission MexqfHapOnHaR 3neKTpoTexHwecKaR KOMIICCIIR Copyright International Electrotechnical Commission Provided by IHS under license with IECNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-2- FDIS 60464-3-1 Amend. 1 O IEC:2006(E) Report on voting FOREWORD Propert

4、ies before drying and curing Density This amendment has been prepared by IEC technical committee 15: Electrical insulating materials. Properties after curing Bend test Effect of varnish on enamelled wire pH (W and E varnishes) I 151254lFDIS I 1 512 8 1 IRV D I Breakdown voltage and electric strength

5、 Resistance to mould growth Full information on the voting for the approval of this amendment can be found in the report on voting indicated in the above table. The committee has decided that the contents of this amendment and the base publication will remain unchanged until the maintenance result d

6、ate indicated on the IEC web site under “http:/webstore.iec.ch“ in the data related to the specific publication. At this date, the publication will be reconfirmed, withdrawn, amended. replaced by a revised edition, or Page 9 Replace Table 1 as follows: I Dilution ability I Cupping test I I Stability

7、 in an open vessel I Resistance to liquids (Including water) I I Drying andlor curing in a thick layer I Dissipation factor and relative permittivity I I Volatile organic content (W and E varnishes) I Flash rusting of steel panels I I Water content (W and E varnishes) I I Copyright International Ele

8、ctrotechnical Commission Provided by IHS under license with IECNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Copyright International Electrotechnical Commission Provided by IHS under license with IECNot for ResaleNo reproduction or networking permitted without li

9、cense from IHS-,-,-ISBN 2-8318-8456-X ICs 29.035.01 Typeset and printed by the IEC Central Office GENEVA, SWITZERLAND Copyright International Electrotechnical Commission Provided by IHS under license with IECNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-NORME CE1

10、 INTERNATIONALE INTERNATIONAL STANDARD IEC 60464-3-1 Deuxime dition Second edition 2001 -07 Vernis utiliss comme isolants lectriques - Partie 3: Spcifications pour matriaux particuliers - Feuille 1 : Vernis de finition durcissant temprature ambiante Varnishes used for electrical insulation - Part 3:

11、 Specifications for individual materials - Sheet 1 : Ambient curing finishing varnishes Numro de rfrence Reference number CEIIIEC 60464-3-1 :2001 Copyright International Electrotechnical Commission Provided by IHS under license with IECNot for ResaleNo reproduction or networking permitted without li

12、cense from IHS-,-,-Numrotation des publications Depuis le ler janvier 1997, les publications de la CE1 sont numrotes partir de 60000. Ainsi, la CE1 34-1 devient la CE1 60034-1. Editions consolides Les versions consolides de certaines publications de la CE1 incorporant les amendements sont disponible

13、s. Par exemple, les numros ddition 1 .O, 1 .I et 1.2 indiquent respectivement la publication de base, la publication de base incorporant lamendement 1, et la publication de base incorporant les amendements 1 et 2. Informations supplmentaires sur les publications de la CE1 Le contenu technique des pu

14、blications de la CE1 est constamment revu par la CE1 afin quil reflte ltat actuel de la technique. Des renseignements relatifs cette publication, y compris sa validit, sont dispo- nibles dans le Catalogue des publications de la CE1 (voir ci-dessous) en plus des nouvelles ditions, amendements et corr

15、igenda. Des informations sur les sujets ltude et lavancement des travaux entrepris par le comit dtudes qui a labor cette publication, ainsi que la liste des publications parues, sont galement disponibles par lintermdiaire de: Site web de la CE1 (www.8ec.ch) Catalogue des publications de la CE1 Le ca

16、talogue en ligne sur le site web de la CE1 (www.iec.ch/catla-f.htm) vous permet de faire des recherches en utilisant de nombreux critres, comprenant des recherches textuelles, par comit dtudes ou date de publication. Des informations en ligne sont galement disponibles sur les nouvelles publications,

17、 les publications rempla- ces ou retires, ainsi que sur les corrigenda. IEC Just Published Ce rsum des dernires publications parues (www/.iec.ch/JP.htm) est aussi disponible par courrier lectronique. Veuillez prendre contact avec le Service client (voir ci-dessous) pour plus dinformations. Service c

18、lients Si vous avez des questions au sujet de cette publication ou avez besoin de renseignements supplmentaires, prenez contact avec le Service clients: Email: custserriec.ch TI: +41 22 919 02 11 Fax: +41 22 919 03 O0 Publication numbering As from 1 January 1997 all IEC publications are issued with

19、a designation in the 60000 series. For example, IEC 34-1 is now referred to as IEC 60034-1. Consolidated editions The IEC is now publishing consolidated versions of its publications. For example, edition numbers 1 .O, 1 .I and 1.2 refer, respectively, to the base publication, the base publication in

20、corporating amendment 1 and the base publication incorporating amendments 1 and 2. Further information on IEC publications The technical content of IEC publications is kept under constant review by the IEC, thus ensuring that the content reflects current technology. Information relating to this publ

21、ication, including its validity, is available in the IEC Catalogue of publications (see below) in addition to new editions, amendments and corrigenda. Information on the subjects under consideration and work in progress undertaken by the technical committee which has prepared this publication, as we

22、ll as the list of publications issued, is also available from the following: IEC Web Site (www.iec.ch) Catalogue of IEC publications The on-line catalogue on the IEC web site (www.iec.chlcat8a-e.htm) enables you to search by a variety of criteria including text searches, technical committees and dat

23、e of publication. On- line information is also available on recently issued publications, withdrawn and replaced publications, as well as corrigenda. IEC Just Published This summary of recently issued publications (www.iec.ch/JP.htm) is also available by email. Please contact the Customer Service Ce

24、ntre (see below) for further information. Customer Service Centre If you have any questions regarding this publication or need further assistance, please contact the Customer Service Centre: Email: custserv,iec.ch Tel: +41 22 91 9 02 11 Fax: +41 22 919 03 O0 Copyright International Electrotechnical

25、Commission Provided by IHS under license with IECNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-NORME CE1 IEC INTERNATIONALE INTERNATIONAL STANDARD 60464-3-1 Deuxime dition Second edition 2001 -07 Vernis utiliss comme isolants lectriques - Partie 3: Spcifications

26、pour matriaux particuliers - Feuille 1 : Vernis de finition durcissant temprature ambiante Varnishes used for electrical insulation - Part 3: Specifications for individual materials - Sheet 1 : Ambient curing finishing varnishes O IEC 2001 Droits de reproduction rservs - Copyright - all rights reser

27、ved Aucune partie de cette publication ne peut tre reproduite ni No part of this publication may be reproduced or utilized in utilis4e sous quelque forme que ce soit et par aucun proc4d4, any form or by any means, electronic or mechanical, 4lectronique ou m4canique, y compris la photocopie et les in

28、cluding photocopying and microfilm, without permission in microfilms, sans laccord 4crit de 14diteur. writing from the publisher. International Electrotechnical Commission Telefax: +41 22 91 9 0300 3, rue de Varemb Geneva, Switzerland IEC web site http:/www.iec.ch e-mail: inmailiec.ch CODE PRIX Comm

29、ission Electrotechnique Internationale PRICECODE F International Electrotechnical Commission MemnvHaponHaR KTPOTXHHCHR HOMHCCMR Pourprix, voir catalogue en vigueur O Forprice, see current catalogue Copyright International Electrotechnical Commission Provided by IHS under license with IECNot for Resa

30、leNo reproduction or networking permitted without license from IHS-,-,-2- 60464-3-1 O CEI:2001 1 5Cll22 1 /FD IS COMMISSION LECTROTECHNIQUE INTERNATIONALE 15C/l250/RVD VERNIS UTILISS COMME ISOLANTS LECTRIQUES- Partie 3: Spcifications pour matriaux particuliers - Feuille 1: Vernis de finition durciss

31、ant temprature ambiante AVANT-PROPOS La CE1 (Commission lectrotechnique Internationale) est une organisation mondiale de normalisation compose de lensemble des comits lectrotechniques nationaux (Comits nationaux de la CEI). La CE1 a pour objet de favoriser la coopration internationale pour toutes le

32、s questions de normalisation dans les domaines de llectricit et de llectronique. A cet effet, la CEI, entre autres activits, publie des Normes internationales. Leur laboration est confie des comits dtudes, aux travaux desquels tout Comit national intress par le sujet trait peut participer. Les organ

33、isations internationales, gouvernementales et non gouvernementales, en liaison avec la CEI, participent galement aux travaux. La CE1 collabore troitement avec lOrganisation Internationale de Normalisation (ISO), selon des conditions fixes par accord entre les deux organisations. Les dcisions ou acco

34、rds officiels de la CE1 concernant les questions techniques reprsentent, dans la mesure du possible, un accord international sur les sujets tudis, tant donn que les Comits nationaux intresss sont reprsents dans chaque comit dtudes. Les documents produits se prsentent sous la forme de recommandations

35、 internationales. Ils sont publis comme normes, spcifications techniques, rapports techniques ou guides et agrs comme tels par les Comits nationaux. Dans le but dencourager lunification internationale, les Comits nationaux de la CE1 sengagent appliquer de faon transparente, dans toute la mesure poss

36、ible, les Normes internationales de la CE1 dans leurs normes nationales et rgionales. Toute divergence entre la norme de la CE1 et la norme nationale ou rgionale correspondante doit tre indique en termes clairs dans cette dernire. La CE1 na fix aucune procdure concernant le marquage comme indication

37、 dapprobation et sa responsabilit nest pas engage quand un matriel est dclar conforme lune de ses normes. Lattention est attire sur le fait que certains des lments de la prsente Norme internationale peuvent faire lobjet de droits de proprit intellectuelle ou de droits analogues. La CE1 ne saurait tr

38、e tenue pour responsable de ne pas avoir identifi de tels droits de proprit et de ne pas avoir signal leur existence. La Norme internationale CE1 60464-3-1 a t tablie par le sous-comit 15C: Spcifications, du comit dtudes 15 de la CEI: Matriaux isolants. Cette deuxime dition annule et remplace la pre

39、mire dition, parue en 1986. Le texte de cette norme est issu des documents suivants: I FDIS I Rapport devote I Le rapport de vote indiqu dans le tableau ci-dessus donne toute information sur le vote ayant abouti lapprobation de cette norme. Cette publication a t rdige selon les Directives ISO/CEI, P

40、artie 3. Le comit a dcid que le contenu de cette publication ne sera pas modifi avant 2005. A cette date, la publication sera reconduite; supprime; amende. remplace par une dition rvise, ou Copyright International Electrotechnical Commission Provided by IHS under license with IECNot for ResaleNo rep

41、roduction or networking permitted without license from IHS-,-,-60464-3-1 O IEC:2001 -3- 1 5Cll22 1 /FD IS INTERNATIONAL ELECTROTECHNICAL COMMISSION 15C/l250/RVD VARNISHES USED FOR ELECTRICAL INSULATION - Part 3: Specifications for individual materials - Sheet 1: Ambient curing finishing varnishes FO

42、REWORD 1) The IEC (International Electrotechnical Commission) is a worldwide organization for standardization comprising all national electrotechnical committees (IEC National Committees). The object of the IEC is to promote international co-operation on all questions concerning standardization in t

43、he electrical and electronic fields. To this end and in addition to other activities, the IEC publishes International Standards. Their preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with may participate in this preparatory work. Internati

44、onal, governmental and non-governmental organizations liaising with the IEC also participate in this preparation. The IEC collaborates closely with the International Organization for Standardization (ISO) in accordance with conditions determined by agreement between the two organizations. 2) The for

45、mal decisions or agreements of the IEC on technical matters express, as nearly as possible, an international consensus of opinion on the relevant subjects since each technical committee has representation from all interested National Committees. 3) The documents produced have the form of recommendat

46、ions for international use and are published in the form of standards, technical specifications, technical reports or guides and they are accepted by the National Committees in that sense. 4) In order to promote international unification, IEC National Committees undertake to apply IEC International

47、Standards transparently to the maximum extent possible in their national and regional standards. Any divergence between the IEC Standard and the corresponding national or regional standard shall be clearly indicated in the latter. 5) The IEC provides no marking procedure to indicate its approval and

48、 cannot be rendered responsible for any equipment declared to be in conformity with one of its standards. 6) Attention is drawn to the possibility that some of the elements of this International Standard may be the subject of patent rights. The IEC shall not be held responsible for identifying any or all such patent rights. International Standard IEC 60464-3-1 has been prepared by subcommittee 15C: Specifications, of IEC technical committee 15: I