ISO 8116-5-2008 Textile machinery and accessories - Beams for winding - Part 5 Sectional beams for warp knitting machines《纺织机械和附件 卷线轴 第5部分 经编机用分段轴》.pdf

《ISO 8116-5-2008 Textile machinery and accessories - Beams for winding - Part 5 Sectional beams for warp knitting machines《纺织机械和附件 卷线轴 第5部分 经编机用分段轴》.pdf》由会员分享，可在线阅读，更多相关《ISO 8116-5-2008 Textile machinery and accessories - Beams for winding - Part 5 Sectional beams for warp knitting machines《纺织机械和附件 卷线轴 第5部分 经编机用分段轴》.pdf（10页珍藏版）》请在麦多课文档分享上搜索。

1、 Reference number ISO 8116-5:2008(E) ISO 2008INTERNATIONAL STANDARD ISO 8116-5 Third edition 2008-12-15 Textile machinery and accessories Beams for winding Part 5: Sectional beams for warp knitting machines Matriel pour lindustrie textile Ensouples pour enroulement Partie 5: Ensouples sectionnelles

2、pour mtiers mailles jetes ISO 8116-5:2008(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobes licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer perfo

3、rming the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobes licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PD

4、F file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central S

5、ecretariat at the address given below. COPYRIGHT PROTECTED DOCUMENT ISO 2008 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in w

6、riting from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in Switzerland ii ISO 2008 All rights reservedISO 811

7、6-5:2008(E) ISO 2008 All rights reserved iii Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each memb

8、er body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Ele

9、ctrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adop

10、ted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of pate

11、nt rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 8116-5 was prepared by Technical Committee ISO/TC 72, Textile machinery and accessories, Subcommittee SC 3, Machinery for fabric manufacturing including preparatory machinery and accessories. This third e

12、dition cancels and replaces the second edition (ISO 8116-5:1995), which has been technically revised. ISO 8116 consists of the following parts, under the general title Textile machinery and accessories Beams for winding: Part 1: General vocabulary Part 2: Warpers beams Part 3: Weavers beams Part 4:

13、Test methods and quality classification of flanges for weavers beams, warpers beams and sectional beams Part 5: Sectional beams for warp knitting machines Part 6: Beams for ribbon weaving and ribbon knitting Part 7: Beams for dyeing slivers, rovings and yarns Part 8: Definitions of run-out tolerance

14、s and methods of measurement Part 9: Dyeing beams for textile fabrics INTERNATIONAL STANDARD ISO 8116-5:2008(E) ISO 2008 All rights reserved 1 Textile machinery and accessories Beams for winding Part 5: Sectional beams for warp knitting machines 1 Scope This part of ISO 8116 specifies the main dimen

15、sions, mechanical strength, designation and permissible values of tolerances of form and position for the main elements of sectional beams for warp knitting machines. For cases where a limit must be fixed for the residual imbalance, a recommendation is made for the choice of quality grade. 2 Normati

16、ve references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 286-2, ISO system of limits and

17、 fits Part 2: Tables of standard tolerance grades and limit deviations for holes and shafts ISO 1940-1, Mechanical vibration Balance quality requirements for rotors in a constant (rigid) state Part 1: Specification and verification of balance tolerances ISO 8116-4, Textile machinery and accessories

18、Beams for winding Part 4: Test methods and quality classification of flanges for weavers beams, warpers beams and sectional beams ISO 8116-8, Textile machinery and accessories Beams for winding Part 8: Definitions of run-out tolerances and methods of measurement 3 Main dimensions The main dimensions

19、 of the sectional beams are given and explained in Figure 1. The main dimensions of the sectional beams given in Table 1 shall be met. ISO 8116-5:2008(E) 2 ISO 2008 All rights reservedKey d 1flange diameter d 2outside barrel diameter d 3bore diameter of flange l 1length between flanges l 2overall le

20、ngth b width of keyway h d 3+ keyway depth Figure 1 Sectional beam Table 1 Main dimensions Dimensions in millimetres d 1 3 l 2 1 d 2amin d 3H11 bb min h min 355 355 535 110 70,4 14,2 75 532 535 1 065 1 270 1 325 196 762 298 1 000 1 065 1 270 1 325 360 152,7 19,6 165,3 aMinimum values depending on th

21、e setting device of the machine. bStandard tolerance grades and limit deviations in accordance with ISO 286-2. ISO 8116-5:2008(E) ISO 2008 All rights reserved 3 4 Mechanical strength The mechanical strength of sectional beams for knitting machines is classified in accordance with the quality classes

22、 defined in ISO 8116-4. The mechanical strength of sectional beams for knitting machines shall be verified, depending on the quality class, by the test method given in ISO 8116-4. 5 Circular axial run-out tolerance, T a , of flanges The permissible circular axial run-out tolerance, T a , of flanges

23、given in with Table 2 shall be met. The run-out tolerance shall be measured in accordance with ISO 8116-8. Table 2 Permissible circular axial run-out tolerance of flanges d 1mm T amm 335 0,2 532 0,35 762 0,5 1 000 0,75 6 Total run-out tolerance, T r , of barrel The permissible total run-out toleranc

24、e, T r , of the barrel shall be measured in millimetres and calculated using Equation (1): 1 r 0,25 1000 l T = (1) The run-out tolerance shall be measured in accordance with ISO 8116-8. 7 Residual imbalance Depending on the circumstances, it may be necessary to fix a value for the residual imbalance

25、 of sectional beams. In general, a quality grade G 6,3 in accordance with ISO 1940-1 will be appropriate. If special conditions call for another grade, this shall be specified. 8 Taper reception At a flange diameter, d 1 , of 762 mm or greater, the sectional beam may be designed with a taper recepti

26、on as given in Figure 2 in order to achieve a better centring on mandrel. ISO 8116-5:2008(E) 4 ISO 2008 All rights reservedFigure 2 Taper reception 9 Other specifications The following details should be specified as appropriate: a) materials of the barrel and flanges; b) nature of the material to be

27、 wound; c) fabrication process of the sectional beam flanges (casting or forging); d) surface quality and, if possible, the treatment (paint, chromium-plating, nickel-plating, etc.) of the beam in contact with the material to be wound (inner sides of the flanges and the surface of the outside barrel

28、 diameter); e) number of grooves (one or two) to be included in the boss of each flange; f) taper reception (if received). 10 Designation The designation of a sectional beam in accordance with this part of ISO 8116 shall include the following information in the order given: a) “Sectional beam”; b) r

29、eference to this part of ISO 8116, i.e. ISO 8116-5; c) flange diameter, d 1 , in millimetres; d) overall length, l 2 , in millimetres; e) quality class Q1, Q2, Q3 or Q4 in accordance with ISO 8116-4. EXAMPLE A sectional beam for warp knitting machines with flange diameter d 1= 535 mm and overall length l 2= 1 065 mm with the quality class Q4 shall be designated as follows: Sectional beam ISO 8116-5 - 535 1 065-Q4 ISO 8116-5:2008(E) ICS 59.120.20 Price based on 4 pages ISO 2008 All rights reserved