ISO 8116-2-2008 Textile machinery and accessories - Beams for winding - Part 2 Warper-s beams《纺织机械和附件 经轴 第2部分 整经轴》.pdf

《ISO 8116-2-2008 Textile machinery and accessories - Beams for winding - Part 2 Warper-s beams《纺织机械和附件 经轴 第2部分 整经轴》.pdf》由会员分享，可在线阅读，更多相关《ISO 8116-2-2008 Textile machinery and accessories - Beams for winding - Part 2 Warper-s beams《纺织机械和附件 经轴 第2部分 整经轴》.pdf（12页珍藏版）》请在麦多课文档分享上搜索。

1、 Reference number ISO 8116-2:2008(E) ISO 2008INTERNATIONAL STANDARD ISO 8116-2 Third edition 2008-12-15 Textile machinery and accessories Beams for winding Part 2: Warpers beams Matriel pour lindustrie textile Ensouples pour enroulement Partie 2: Ensouples dourdissoirs ISO 8116-2:2008(E) PDF disclai

2、mer This PDF file may contain embedded typefaces. In accordance with Adobes licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties acc

3、ept therein the responsibility of not infringing Adobes licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the

4、file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below. COPYRIGHT PROTECT

5、ED DOCUMENT ISO 2008 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISOs memb

6、er body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in Switzerland ii ISO 2008 All rights reservedISO 8116-2:2008(E) ISO 2008 All rights reserved iii Foreword IS

7、O (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical co

8、mmittee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electro

9、technical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the me

10、mber bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identif

11、ying any or all such patent rights. ISO 8116-2 was prepared by Technical Committee ISO/TC 72, Textile machinery and accessories, Subcommittee SC 3, Machinery for fabric manufacturing including preparatory machinery and accessories. This third edition cancels and replaces the second edition (ISO 8116

12、-2:1995), which has been technically revised. ISO 8116 consists of the following parts, under the general title Textile machinery and accessories Beams for winding: Part 1: General vocabulary Part 2: Warpers beams Part 3: Weavers beams Part 4: Test methods and quality classification of flanges for w

13、eavers beams, warpers beams and sectional beams Part 5: Sectional beams for warp knitting machines Part 6: Beams for ribbon weaving and ribbon knitting Part 7: Beams for dyeing slivers, rovings and yarns Part 8: Definitions of run-out tolerances and methods of measurement Part 9: Dyeing beams for te

14、xtile fabrics INTERNATIONAL STANDARD ISO 8116-2:2008(E) ISO 2008 All rights reserved 1 Textile machinery and accessories Beams for winding Part 2: Warpers beams 1 Scope This part of ISO 8116 specifies the main dimensions, mechanical strength, permissible tolerances of form and position of the main e

15、lements of warpers beams, and the driving devices and designation for warpers beams with and without shafts. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references,

16、 the latest edition of the referenced document (including any amendments) applies. ISO 286-2, ISO system of limits and fits Part 2: Tables of standard tolerance grades and limit deviations for holes and shafts ISO 1940-1, Mechanical vibration Balance quality requirements for rotors in a constant (ri

17、gid) state Part 1: Specification and verification of balance tolerances ISO 8116-4, Textile machinery and accessories Beams for winding Part 4: Test methods and quality classification of flanges for weavers beams, warpers beams and sectional beams ISO 8116-8, Textile machinery and accessories Beams

18、for winding Part 8: Definitions of run-out tolerances and methods of measurement 3 Types and main dimensions Warpers beams are divided into three main types: Type A warpers beams with shafts; Type B warpers beams with cylinder bore for centring and key seat for driving; Type C warpers beams with too

19、thed cone for centring and driving: Execution C1: tooth number 50 (old executions shall no be longer used) Execution C2: tooth number 72 Execution C3: tooth number 50 The main dimensions of warpers beams of Type A and Type B are shown and explained in Figure 1 and Figure 2. ISO 8116-2:2008(E) 2 ISO

20、2008 All rights reservedThe main dimensions of warpers beams of Type C are shown and explained in Figure 3. The main dimensions of warpers beams of Type A and Type B, as given in Table 1, shall be met. The main dimensions of warpers beams of Type C, as given in Table 2, shall be met. Key d 1flange d

21、iameter d 2barrel diameter d 3shaft diameter aTwo pegs for drive pins. l 1distance between the flanges l 2overall length (without shafts) l 3length or extension of shaft l 4total length (with shafts) Figure 1 Warpers beams with shafts Type A Key d 1flange diameter d 2barrel diameter l 1distance betw

22、een the flanges l 2overall length (without shafts) aStandard tolerance grades and limit deviations in accordance with ISO 286-2. Figure 2 Warpers beams with cylinder bore for centring and keyseat for driving Type B ISO 8116-2:2008(E) ISO 2008 All rights reserved 3Figure 3 (continued) ISO 8116-2:2008

23、(E) 4 ISO 2008 All rights reservedKey 1 execution C1: tooth number 50 2 execution C2: tooth number 72 3 execution C3: tooth number 50 d 1flange diameter d 2barrel diameter d 3shaft diameter d 4bore diameter for shaft d 5ruffle diameter l 1distance between the flanges l 2overall length (without shaft

24、s) l 3length or extension of shaft Figure 3 Warpers beams with toothed cone for centring and driving Type C Table 1 Warpers beams main dimensions Types A and B Dimensions in millimetres d 1 1,5 d 2 5 d 3h11 bl 1a+1,5 0 l 20 2 l 3l 4815 915 38 50 1 015 1 250 300 (320) 50 1 378 1 524 1 800 2 000 l 1+

25、150 120 l 2+ 2 l 3NOTE The dimensions in parentheses should be avoided whenever possible. aIf distances of more than 2 000 mm between flanges are necessary, increments of 200 mm shall be selected. bStandard tolerance grades and limit deviations in accordance with ISO 286-2. Table 2 Warpers beams mai

26、n dimensions Type C Dimensions in millimetres d 1d 2d 3d 4d 5Execution l 1al 2l 3 1,5 5 h11 bE9 bC1 C2 C3 +1,5 0 0 2 800 (900) 38 50 38 50 1 000 300 (320) 50 50 245 245 l 1+ 270 (1 100) 360 1 250 400 1 400 450 60 60 260 295 260 (1 374) 1 400 (1 524) 1 600 1 800 2 000 l 1+ 320 120 150 NOTE The dimens

27、ions in parentheses should be avoided whenever possible. a If distances of more than 2 000 mm between flanges are necessary, increments of 200 mm shall be selected. b Standard tolerance grades and limit deviations in accordance with ISO 286-2. ISO 8116-2:2008(E) ISO 2008 All rights reserved 5 4 Mech

28、anical strength The mechanical strength of warpers beam flanges is classified in accordance with the quality classes defined in ISO 8116-4. The mechanical strength of warpers beam flanges shall be verified, depending on the quality class, using the test method described in ISO 8116-4. 5 Circular axi

29、al run-out tolerance, T a , of flanges The permissible circular axial run-out tolerances, T a , of flanges, as given in Table 3, shall be met. The run-out tolerances shall be measured in accordance with ISO 8116-8. Table 3 Permissible circular axial run-out tolerance of flanges d 1mm T amm d 1 u 915

30、 0,5 d 1 915 0,75 6 Total run-out tolerance, T r , of the barrel The permissible total run-out tolerances, T r , of the barrel shall be derived using the formulae given in Table 4. The run-out tolerances shall be measured in accordance with ISO 8116-8. Table 4 Total barrel run-out tolerances Yarn to

31、 be wound T rmm Filament yarn 1 0,25 1000 lSpun yarn 1 0,4 1000 l7 Residual imbalance Depending on the circumstances, it may be necessary to fix a value for the residual imbalance of warpers beams. In general, a quality grade G 6,3 in accordance with ISO 1940-1 will be appropriate. If special condit

32、ions call for another grade, this shall be specified. ISO 8116-2:2008(E) 6 ISO 2008 All rights reserved8 Designation The designation of a warpers beam in accordance with this part of ISO 8116 shall include the following information in the order given: a) “Warpers beam”; b) reference to this part of

33、ISO 8116, i.e. ISO 8116-2; c) Type A or B or C1 or C2 or C3 of warpers beam for the form of centring and driving; d) flange diameter, d 1 , in millimetres; e) shaft diameter, d 3 , in millimetres (only for types A and B); f) distance between flanges, l 1 , in millimetres; g) length or extension of s

34、haft, l 3 , in millimetres (only for types C1, C2 or C3); h) quality class Q1, Q2, Q3 or Q4 in accordance with ISO 8116-4. EXAMPLE 1 A warpers beam, type A, with a flange diameter d 1of 915 mm, shaft diameter d 3of 50 mm and distance between flanges l 1of 1 800 mm with the quality class Q2 in accord

35、ance with ISO 8116-4 shall be designated as follows: Warpers beam ISO 8116-2 - A-915 50 1 800-Q2 EXAMPLE 2 A warpers beam, type C3, with a flange diameter d 1of 1 250 mm, distance between flanges l 1of 1 800 mm and l 3of 150 mm with the quality class Q2 in accordance with ISO 8116-4 shall be designated as follows: Warpers beam ISO 8116-2 - C3-1 250 1 800 150-Q2 ISO 8116-2:2008(E) ICS 59.120.20 Price based on 6 pages ISO 2008 All rights reserved