ISO 14710-1996 Equipment for crop protection - Air-assisted sprayers - Dimensions of nozzle swivel nuts《作物保护设备 空气引射喷雾器 喷嘴旋转螺母的尺寸》.pdf

《ISO 14710-1996 Equipment for crop protection - Air-assisted sprayers - Dimensions of nozzle swivel nuts《作物保护设备 空气引射喷雾器 喷嘴旋转螺母的尺寸》.pdf》由会员分享，可在线阅读，更多相关《ISO 14710-1996 Equipment for crop protection - Air-assisted sprayers - Dimensions of nozzle swivel nuts《作物保护设备 空气引射喷雾器 喷嘴旋转螺母的尺寸》.pdf（4页珍藏版）》请在麦多课文档分享上搜索。

1、INTERNATIONAL STANDARD IS0 14710 First edition 1996-l 2-15 Equipment for crop protection - Air-assisted sprayers - Dimensions of nozzle swivel nuts Matkiel de protection des cultures - Pulv6risateur.s 9 jet port6 - Dimensions des Bcrous-raccords de buse Reference number IS0 14710 1996(E) Copyright I

2、nternational Organization for Standardization Provided by IHS under license with ISONot for ResaleNo reproduction or networking permitted without license from IHS-,-,-IS0 14710:1996(E) Foreword IS0 (the International Organization for Standardization) is a worldwide federation of national standards b

3、odies (IS0 member bodies). The work of preparing International Standards is normally carried out through IS0 technical committees Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizatio

4、ns, governmental and non-governmental, in liaison with ISO, also take part in the work. IS0 collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. Draft International Standards adopted by the technical committees are circulat

5、ed to the member bodies for voting Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. International Standard IS0 14710 was prepared by Technical Committee lSO/TC 23, Tractors and machinery for agriculture and forestry, Sub- committee SC 6

6、, Equipment for crop protection. 0 IS0 1996 All rights reserved Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from the publisher. Interna

7、tional Organization for Standardization Case Postale 56. CH-1211 Geneve 20 l Switzerland Printed in Switzerland ii Copyright International Organization for Standardization Provided by IHS under license with ISONot for ResaleNo reproduction or networking permitted without license from IHS-,-,-INTERNA

8、TIONAL STANDARD 0 IS0 IS0 14710:1996(E) Equipment for crop protection - Air-assisted sprayers - Dimensions of nozzle swivel nuts 1 Scope This International Standard specifies the outer dimensions of the swivel nuts of nozzles for air-assisted sprayers NOTE - The nozzle output is very often determine

9、d when testing air-assisted sprayers It is necessary to fit measurement devices to the swivel nuts to collect the liquid If the outer dimensions of the nuts are standardized, the number of fitting pieces can be reduced and testing is then simplified The defined dimensions simplify the fitting of mea

10、surement devices to the swivel nuts (for example, for the determination of the nozzle output). 2 Dimensions The swivel nuts shall be conical with outer dimensions that correspond to figure 1 and table 1. Table 1 Dimensions in millimetres d 1 f0.1 min 25 15 30 15 35 15 40 15 Figure 1 1 Copyright Inte

11、rnational Organization for Standardization Provided by IHS under license with ISONot for ResaleNo reproduction or networking permitted without license from IHS-,-,-IS0 14710:1996(E) ICS 65.060.40 Descriptors: agricultural equipment, crop protection, crops treatment equipment, agricultural sprayers, nozzles, sprayer nozzles, swivels, nuts (fasteners), dimensions Price based on 1 page Copyright International Organization for Standardization Provided by IHS under license with ISONot for ResaleNo reproduction or networking permitted without license from IHS-,-,-