IEEE C62 33-2016 en Test Methods and Performance Values for Metal-Oxide Varistor Surge Protective Components.pdf

《IEEE C62 33-2016 en Test Methods and Performance Values for Metal-Oxide Varistor Surge Protective Components.pdf》由会员分享，可在线阅读，更多相关《IEEE C62 33-2016 en Test Methods and Performance Values for Metal-Oxide Varistor Surge Protective Components.pdf（46页珍藏版）》请在麦多课文档分享上搜索。

1、IEEE Standard for Test Methods and Performance Values for Metal-Oxide Varistor Surge Protective Components IEEE Std C62.33-2016 (Revision of IEEE Std C62.33-1982) IEEE Power and Energy Society Sponsored by the Surge Protective Devices Committee IEEE 3 Park Avenue New York, NY 10016-5997 USAIEEE Std

2、C62.33-2016 (Revision of IEEE Std C62.33-1982) IEEE Standard for Test Methods and Performance Values for Metal-Oxide Varistor Surge Protective Components Sponsor Surge Protective Devices Committee of the IEEE Power and Energy Society Approved 7 December 2016 IEEE-SA Standards BoardAbstract: Test met

3、hods and preferred values for metal-oxide varistor (MOV) surge protective components are covered in this standard and have the following main parameter ranges: packaging (leaded disc-type or surface mount), nominal varistor voltage (5 V to 1200 V), 8/20 surge current rating (10 A to 70 kA), and 8/20

4、 clamping voltage (10 V to 3 kV). With appropriate component selection, these components could be used for the overvoltage protection of power and signal systems having continuous ac voltages (2.5 V rms to 750 V rms), steady-state dc voltages (3.3 V to 1000 V), and peak signal feed voltages (3.5 V t

5、o 850 V). Information is given on manufacturer type testing used to determine environmental performance and rated values. Keywords: clamping voltage, ESD, IEEE C62.33, leaded, MCOV, metal-oxide varistor, MOV, nominal voltage, surface mount, surge current rating, TOV, varistor The Institute of Electr

6、ical and Electronics Engineers, Inc. 3 Park Avenue, New York, NY 10016-5997, USA Copyright 2018 by The Institute of Electrical and Electronics Engineers, Inc. All rights reserved. Published 29 January 2018. Printed in the United States of America. IEEE is a registered trademark in the U.S. Patent fi

7、tness for a particular purpose; non-infringement; and quality, accuracy, effectiveness, currency, or completeness of material. In addition, IEEE disclaims any and all conditions relating to: results; and workmanlike effort. IEEE standards documents are supplied “AS IS” and “WITH ALL FAULTS.” Use of

8、an IEEE standard is wholly voluntary. The existence of an IEEE standard does not imply that there are no other ways to produce, test, measure, purchase, market, or provide other goods and services related to the scope of the IEEE standard. Furthermore, the viewpoint expressed at the time a standard

9、is approved and issued is subject to change brought about through developments in the state of the art and comments received from users of the standard. In publishing and making its standards available, IEEE is not suggesting or rendering professional or other services for, or on behalf of, any pers

10、on or entity nor is IEEE undertaking to perform any duty owed by any other person or entity to another. Any person utilizing any IEEE Standards document, should rely upon his or her own independent judgment in the exercise of reasonable care in any given circumstances or, as appropriate, seek the ad

11、vice of a competent professional in determining the appropriateness of a given IEEE standard. IN NO EVENT SHALL IEEE BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO: PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,

12、DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE PUBLICATION, USE OF, OR RELIANCE UPON ANY STANDARD, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH D

13、AMAGE AND REGARDLESS OF WHETHER SUCH DAMAGE W AS FORESEEABLE.4 Copyright 2018 IEEE. All rights reserved. Translations The IEEE consensus development process involves the review of documents in English only. In the event that an IEEE standard is translated, only the English version published by IEEE

14、should be considered the approved IEEE standard. Official statements A statement, written or oral, that is not processed in accordance with the IEEE-SA Standards Board Operations Manual shall not be considered or inferred to be the official position of IEEE or any of its committees and shall not be

15、considered to be, or be relied upon as, a formal position of IEEE. At lectures, symposia, seminars, or educational courses, an individual presenting information on IEEE standards shall make it clear that his or her views should be considered the personal views of that individual rather than the form

16、al position of IEEE. Comments on standards Comments for revision of IEEE Standards documents are welcome from any interested party, regardless of membership affiliation with IEEE. However, IEEE does not provide consulting information or advice pertaining to IEEE Standards documents. Suggestions for

17、changes in documents should be in the form of a proposed change of text, together with appropriate supporting comments. Since IEEE standards represent a consensus of concerned interests, it is important that any responses to comments and questions also receive the concurrence of a balance of interes

18、ts. For this reason, IEEE and the members of its societies and Standards Coordinating Committees are not able to provide an instant response to comments or questions except in those cases where the matter has previously been addressed. For the same reason, IEEE does not respond to interpretation req

19、uests. Any person who would like to participate in revisions to an IEEE standard is welcome to join the relevant IEEE working group. Comments on standards should be submitted to the following address: Secretary, IEEE-SA Standards Board 445 Hoes Lane Piscataway, NJ 08854 USA Laws and regulations User

20、s of IEEE Standards documents should consult all applicable laws and regulations. Compliance with the provisions of any IEEE Standards document does not imply compliance to any applicable regulatory requirements. Implementers of the standard are responsible for observing or referring to the applicab

21、le regulatory requirements. IEEE does not, by the publication of its standards, intend to urge action that is not in compliance with applicable laws, and these documents may not be construed as doing so. Copyrights IEEE draft and approved standards are copyrighted by IEEE under US and international

22、copyright laws. They are made available by IEEE and are adopted for a wide variety of both public and private uses. These include both use, by reference, in laws and regulations, and use in private self-regulation, standardization, and the promotion of engineering practices and methods. By making th

23、ese documents available for use and adoption by public authorities and private users, IEEE does not waive any rights in copyright to the documents.5 Copyright 2018 IEEE. All rights reserved. Photocopies Subject to payment of the appropriate fee, IEEE will grant users a limited, non-exclusive license

24、 to photocopy portions of any individual standard for company or organizational internal use or individual, non-commercial use only. To arrange for payment of licensing fees, please contact Copyright Clearance Center, Customer Service, 222 Rosewood Drive, Danvers, MA 01923 USA; +1 978 750 8400. Perm

25、ission to photocopy portions of any individual standard for educational classroom use can also be obtained through the Copyright Clearance Center. Updating of IEEE Standards documents Users of IEEE Standards documents should be aware that these documents may be superseded at any time by the issuance

26、 of new editions or may be amended from time to time through the issuance of amendments, corrigenda, or errata. An official IEEE document at any point in time consists of the current edition of the document together with any amendments, corrigenda, or errata then in effect. Every IEEE standard is su

27、bjected to review at least every 10 years. When a document is more than 10 years old and has not undergone a revision process, it is reasonable to conclude that its contents, although still of some value, do not wholly reflect the present state of the art. Users are cautioned to check to determine t

28、hat they have the latest edition of any IEEE standard. In order to determine whether a given document is the current edition and whether it has been amended through the issuance of amendments, corrigenda, or errata, visit the IEEE Xplore at http:/ ieeexplore .ieee .or g/ or contact IEEE at the addre

29、ss listed previously. For more information about the IEEE-SA or IEEEs standards development process, visit the IEEE-SA Website at http:/ standards .ieee .or g. Errata Errata, if any, for all IEEE standards can be accessed on the IEEE-SA Website at the following URL: http:/ standards .ieee .org/ find

30、stds/ errata/ index .html. Users are encouraged to check this URL for errata periodically. Patents Attention is called to the possibility that implementation of this standard may require use of subject matter covered by patent rights. By publication of this standard, no position is taken by the IEEE

31、 with respect to the existence or validity of any patent rights in connection therewith. If a patent holder or patent applicant has filed a statement of assurance via an Accepted Letter of Assurance, then the statement is listed on the IEEE- SA Website at http:/ standards .ieee .or g/ about/ sasb/ p

32、atcom/ patents .html. Letters of Assurance may indicate whether the Submitter is willing or unwilling to grant licenses under patent rights without compensation or under reasonable rates, with reasonable terms and conditions that are demonstrably free of any unfair discrimination to applicants desir

33、ing to obtain such licenses. Essential Patent Claims may exist for which a Letter of Assurance has not been received. The IEEE is not responsible for identifying Essential Patent Claims for which a license may be required, for conducting inquiries into the legal validity or scope of Patents Claims,

34、or determining whether any licensing terms or conditions provided in connection with submission of a Letter of Assurance, if any, or in any licensing agreements are reasonable or non-discriminatory. Users of this standard are expressly advised that determination of the validity of any patent rights,

35、 and the risk of infringement of such rights, is entirely their own responsibility. Further information may be obtained from the IEEE Standards Association.6 Copyright 2018 IEEE. All rights reserved. Participants At the time this standard was submitted to the IEEE-SA Standards Board for approval, th

36、e 3.6.2 L V Solid State Surge Protective Components Working Group had the following membership: Michael J. Maytum, Chair Albert Martin, Vice Chair Tim Ardley Robert Ashton Frank Basciano Nisar Chaudhry Leonard Drewes Bob Fried Ernie Gallo Bogdan Klobassa Peter Kobsa Wolfgang Oertel Thomas Tran Willi

37、am Travis The following members of the individual balloting committee voted on this standard. Balloters may have voted for approval, disapproval, or abstention. Robert Ashton Frank Basciano William Bloethe William Bush Gary Donner Neal Dowling Cliff Erven Sergio Flores Frank Gerleve Randall Groves R

38、aymond Hill Ronald Hotchkiss Laszlo Kadar John Kay Yuri Khersonsky Jim Kulchisky Saumen Kundu Benjamin Lanz Albert Livshitz Albert Martin Michael J. Maytum William McBride Daleep Mohla Arthur Neubauer Michael Newman Wolfgang Oertel Branimir Petosic Thomas Phipps Ulrich Pohl Iulian Profir Michael Rob

39、erts Charles Rogers Thomas Rozek Nikunj Shah Hyeong Sim Jerry Smith David Tepen James Timperley John V ergis Matthew Wakeham James Wilson When the IEEE-SA Standards Board approved this standard on 7 December 2016, it had the following membership: Jean-Philippe Faure, Chair Ted Burse, Vice Chair John

40、 D. Kulick, Past Chair Konstantinos Karachalios, Secretary Chuck Adams Masayuki Ariyoshi Stephen Dukes Jianbin Fan J. Travis Griffith Gary Hoffman Ronald W. Hotchkiss Michael Janezic Joseph L. Koepfinger* Hung Ling Kevin Lu Annette D. Reilly Gary Robinson Mehmet Ulema Yingli Wen Howard Wolfman Don W

41、right Y u Y uan Daidi Zhong *Member Emeritus7 Copyright 2018 IEEE. All rights reserved. Introduction This introduction is not part of IEEE Std C62.33-2016, IEEE Standard for Test Methods and Performance Values for Metal-Oxide V aristor Surge Protective Components. This test method document has been

42、developed for the purpose of testing and comparing metal-oxide varistor (MOV) surge protective components. An MOV is a surge diverter used for limiting transient overvoltages in power and communications circuits. The interest in low-voltage varistors has grown with the trend to highly sophisticated

43、electrical and electronic devices that are exposed to surges from the environment. Initially, there were no standard terms or tests to define or compare these devices. The IEEE Surge Protection Devices Committee formed its Low V oltage Surge Protection Devices Working Group in 1970 to define these p

44、arameters. Experts were drawn from many fields in communications and power utilities, electronic manufacturers and users, test equipment manufacturers and laboratories, and producers of varistors themselves. The requirements, experiences, and vocabularies of these representatives were melded to produce this document as a guide to potential users of varistor surge protective devices.