IEEE 802 3BW-2015 en Ethernet Amendment 1 Physical Layer Specifications and Management Parameters for 100 Mb s Operation over a Single Balanced Twisted Pair Cab.pdf

《IEEE 802 3BW-2015 en Ethernet Amendment 1 Physical Layer Specifications and Management Parameters for 100 Mb s Operation over a Single Balanced Twisted Pair Cab.pdf》由会员分享，可在线阅读，更多相关《IEEE 802 3BW-2015 en Ethernet Amendment 1 Physical Layer Specifications and Management Parameters for 100 Mb s Operation over a Single Balanced Twisted Pair Cab.pdf（88页珍藏版）》请在麦多课文档分享上搜索。

1、 IEEE Standard for Ethernet Amendment 1: Physical Layer Specifications and Management Parameters for 100 Mb/s Operation over a Single Balanced Twisted Pair Cable (100BASE-T1) Sponsored by the LAN/MAN Standards Committee IEEE 3 Park Avenue New York, NY 10016-5997 USA IEEE Computer Society IEEE Std 80

2、2.3bw-2015 (Amendment to IEEE Std 802.3-2015) IEEE Std 802.3bw-2015(Amendment toIEEE Std 802.3-2015)IEEE Standard for EthernetAmendment 1: Physical Layer Specifications and Management Parameters for 100 Mb/s Operation over a Single Balanced Twisted Pair Cable (100BASE-T1)LAN/MAN Standards Committeeo

3、f theIEEE Computer SocietyApproved 26 October 2015IEEE-SA Standards BoardThe Institute of Electrical and Electronics Engineers, Inc.3 Park Avenue, New York, NY 10016-5997, USACopyright 2016 by The Institute of Electrical and Electronics Engineers, Inc.All rights reserved. Published 8 March 2016. Pri

4、nted in the United States of America.IEEE and 802 are registered trademarks in the U.S. Patent copper; Ethernet; IEEE 802.3bw; MASTER-SLAVE; MediumDependent Interface; Physical Coding Sublayer; physical layer; Physical Medium Attachment3Copyright 2016 IEEE. All rights reserved.Important Notices and

5、Disclaimers Concerning IEEE Standards DocumentsIEEE documents are made available for use subject to important notices and legal disclaimers. These noticesand disclaimers, or a reference to this page, appear in all standards and may be found under the heading“Important Notice” or “Important Notices a

6、nd Disclaimers Concerning IEEE Standards Documents.”Notice and Disclaimer of Liability Concerning the Use of IEEE Standards DocumentsIEEE Standards documents (standards, recommended practices, and guides), both full-use and trial-use, aredeveloped within IEEE Societies and the Standards Coordinating

7、 Committees of the IEEE StandardsAssociation (“IEEE-SA”) Standards Board. IEEE (“the Institute”) develops its standards through aconsensus development process, approved by the American National Standards Institute (“ANSI”), whichbrings together volunteers representing varied viewpoints and interests

8、 to achieve the final product.Volunteers are not necessarily members of the Institute and participate without compensation from IEEE.While IEEE administers the process and establishes rules to promote fairness in the consensus developmentprocess, IEEE does not independently evaluate, test, or verify

9、 the accuracy of any of the information or thesoundness of any judgments contained in its standards.IEEE does not warrant or represent the accuracy or content of the material contained in its standards, andexpressly disclaims all warranties (express, implied and statutory) not included in this or an

10、y otherdocument relating to the standard, including, but not limited to, the warranties of: merchantability; fitnessfor a particular purpose; non-infringement; and quality, accuracy, effectiveness, currency, or completeness ofmaterial. In addition, IEEE disclaims any and all conditions relating to:

11、results; and workmanlike effort.IEEE standards documents are supplied “AS IS” and “WITH ALL FAULTS.”Use of an IEEE standard is wholly voluntary. The existence of an IEEE standard does not imply that thereare no other ways to produce, test, measure, purchase, market, or provide other goods and servic

12、es related tothe scope of the IEEE standard. Furthermore, the viewpoint expressed at the time a standard is approved andissued is subject to change brought about through developments in the state of the art and commentsreceived from users of the standard. In publishing and making its standards avail

13、able, IEEE is not suggesting or rendering professional or otherservices for, or on behalf of, any person or entity nor is IEEE undertaking to perform any duty owed by anyother person or entity to another. Any person utilizing any IEEE Standards document, should rely upon hisor her own independent ju

14、dgment in the exercise of reasonable care in any given circumstances or, asappropriate, seek the advice of a competent professional in determining the appropriateness of a given IEEEstandard.IN NO EVENT SHALL IEEE BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL,EXEMPLARY, OR CONSEQUENTIAL DA

15、MAGES (INCLUDING, BUT NOT LIMITED TO:PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; ORBUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY,WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OROTHERWISE) ARISING IN ANY WAY OUT OF THE PUBL

16、ICATION, USE OF, OR RELIANCE UPONANY STANDARD, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE ANDREGARDLESS OF WHETHER SUCH DAMAGE WAS FORESEEABLE.4Copyright 2016 IEEE. All rights reserved.TranslationsThe IEEE consensus development process involves the review of documents in English only. In the

17、eventthat an IEEE standard is translated, only the English version published by IEEE should be considered theapproved IEEE standard.Official statements A statement, written or oral, that is not processed in accordance with the IEEE-SA Standards BoardOperations Manual shall not be considered or infer

18、red to be the official position of IEEE or any of itscommittees and shall not be considered to be, or be relied upon as, a formal position of IEEE. At lectures,symposia, seminars, or educational courses, an individual presenting information on IEEE standards shallmake it clear that his or her views

19、should be considered the personal views of that individual rather than theformal position of IEEE. Comments on standardsComments for revision of IEEE Standards documents are welcome from any interested party, regardless ofmembership affiliation with IEEE. However, IEEE does not provide consulting in

20、formation or advicepertaining to IEEE Standards documents. Suggestions for changes in documents should be in the form of aproposed change of text, together with appropriate supporting comments. Since IEEE standards represent aconsensus of concerned interests, it is important that any responses to co

21、mments and questions also receivethe concurrence of a balance of interests. For this reason, IEEE and the members of its societies andStandards Coordinating Committees are not able to provide an instant response to comments or questionsexcept in those cases where the matter has previously been addre

22、ssed. For the same reason, IEEE does notrespond to interpretation requests. Any person who would like to participate in revisions to an IEEEstandard is welcome to join the relevant IEEE working group.Comments on standards should be submitted to the following address:Secretary, IEEE-SA Standards Boar

23、d 445 Hoes Lane Piscataway, NJ 08854 USALaws and regulations Users of IEEE Standards documents should consult all applicable laws and regulations. Compliance with theprovisions of any IEEE Standards document does not imply compliance to any applicable regulatoryrequirements. Implementers of the stan

24、dard are responsible for observing or referring to the applicableregulatory requirements. IEEE does not, by the publication of its standards, intend to urge action that is notin compliance with applicable laws, and these documents may not be construed as doing so.CopyrightsIEEE draft and approved st

25、andards are copyrighted by IEEE under U.S. and international copyright laws.They are made available by IEEE and are adopted for a wide variety of both public and private uses. Theseinclude both use, by reference, in laws and regulations, and use in private self-regulation, standardization,and the pr

26、omotion of engineering practices and methods. By making these documents available for use andadoption by public authorities and private users, IEEE does not waive any rights in copyright to thedocuments.5Copyright 2016 IEEE. All rights reserved.Photocopies Subject to payment of the appropriate fee,

27、IEEE will grant users a limited, non-exclusive license tophotocopy portions of any individual standard for company or organizational internal use or individual, non-commercial use only. To arrange for payment of licensing fees, please contact Copyright Clearance Center,Customer Service, 222 Rosewood

28、 Drive, Danvers, MA 01923 USA; +1 978 750 8400. Permission tophotocopy portions of any individual standard for educational classroom use can also be obtained throughthe Copyright Clearance Center.Updating of IEEE Standards documents Users of IEEE Standards documents should be aware that these docume

29、nts may be superseded at any timeby the issuance of new editions or may be amended from time to time through the issuance of amendments,corrigenda, or errata. An official IEEE document at any point in time consists of the current edition of thedocument together with any amendments, corrigenda, or er

30、rata then in effect. Every IEEE standard is subjected to review at least every ten years. When a document is more than ten yearsold and has not undergone a revision process, it is reasonable to conclude that its contents, although still ofsome value, do not wholly reflect the present state of the ar

31、t. Users are cautioned to check to determine thatthey have the latest edition of any IEEE standard.In order to determine whether a given document is the current edition and whether it has been amendedthrough the issuance of amendments, corrigenda, or errata, visit the IEEE-SA Website at http:/ieeexp

32、lore.ieee.org/xpl/standards.jsp or contact IEEE at the address listed previously. For more informationabout the IEEE SA or IEEEs standards development process, visit the IEEE-SA Website at http:/standards.ieee.org.Errata Errata, if any, for all IEEE standards can be accessed on the IEEE-SA Website a

33、t the following URL: http:/standards.ieee.org/findstds/errata/index.html. Users are encouraged to check this URL for errataperiodically.PatentsAttention is called to the possibility that implementation of this standard may require use of subject mattercovered by patent rights. By publication of this

34、 standard, no position is taken by the IEEE with respect to theexistence or validity of any patent rights in connection therewith. If a patent holder or patent applicant hasfiled a statement of assurance via an Accepted Letter of Assurance, then the statement is listed on the IEEE-SA Website at http

35、:/standards.ieee.org/about/sasb/patcom/patents.html. Letters of Assurance may indicatewhether the Submitter is willing or unwilling to grant licenses under patent rights without compensation orunder reasonable rates, with reasonable terms and conditions that are demonstrably free of any unfairdiscri

36、mination to applicants desiring to obtain such licenses.Essential Patent Claims may exist for which a Letter of Assurance has not been received. The IEEE is notresponsible for identifying Essential Patent Claims for which a license may be required, for conductinginquiries into the legal validity or

37、scope of Patents Claims, or determining whether any licensing terms orconditions provided in connection with submission of a Letter of Assurance, if any, or in any licensingagreements are reasonable or non-discriminatory. Users of this standard are expressly advised thatdetermination of the validity

38、 of any patent rights, and the risk of infringement of such rights, is entirely theirown responsibility. Further information may be obtained from the IEEE Standards Association.6Copyright 2016 IEEE. All rights reserved.ParticipantsThe following individuals were officers and members of the IEEE 802.3

39、 working group at the beginning ofthe IEEE P802.3bw working group ballot. Individuals may have not voted, voted for approval, disapprovalor abstained on this standard.David J. Law, IEEE 802.3 Working Group ChairAdam Healey, IEEE 802.3 Working Group Vice-ChairPete Anslow, IEEE 802.3 Working Group Sec

40、retarySteven B. Carlson, IEEE 802.3 Working Group Executive SecretaryValerie Maguire, IEEE 802.3 Working Group TreasurerThomas Hogenmller, IEEE P802.3bw 100BASE-T1 Task Force Chair, Phase 1Steven B. Carlson, IEEE P802.3bw 100BASE-T1 Task Force Chair, Phase 2Mehmet Tazebay, IEEE P802.3bw 100BASE-T1 T

41、ask Force Vice-ChairCurtis Donahue, IEEE P802.3bw 100BASE-T1 Task Force Editor-in-Chief Ghani AbbasJohn AbbottDavid AbramsonShadi AbughazalehFaisal AhmadMichel AllardDale AmasonOleksandr BabenkoKoussalya BalasubramanianThananya BaldwinDenis BeaudoinChristian BeiaYakov BelopolskyMichael BennettGary B

42、ernsteinVipul BhattWilliam BlissBrad BoothMartin BoudaEdward BoydDavid BrandtRalf-Peter BraunTheodore BrillhartPaul BrooksAlan BrownDavid BrownMatthew BrownThomas BrownPhillip BrownleeMark BuggJuan-Carlos CalderonJ. Martin CarrollMandeep ChadhaDavid ChalupskyXin ChangWheling ChengAhmad ChiniGolam Ch

43、oudhuryPeter CibulaChristopher R. ColeKeith ConroyEugene DaiShaoan DaiJohn DAmbrosiaMike DarlingYair DarshanPiers DaweFred DawsonWilliam DelveauxJohn DickinsonChris DiminicoThuyen DinhDan DoveMike DudekDavid DwelleyHesham ElbakouryDavid EstesJohn EwenJosef FallerArash FarhoodfarShahar FeldmanAlan Fl

44、atmanHoward FrazierRichard FroschMichael FurlongMike GardnerAli GhiasiJoel GoergenZhigang GongJames GrabaRobert GrowMark GustlinMarek HajduczeniaBernie HammondJeffrey HeathCarl HermanDavid HessYasuo HidakaRiu HiraiBrian HoldenRita HornerBernd HorrmeyerVictor HouRui HuaLiang-wei HuangScott IrwinKazuh

45、iko IshibeHideki IsonoTom IssenhuthMitsuru IwaokaKenneth JacksonJack JewellWenbin JiangAndrew JimenezChad JonesAntony JosephYasuaki KawatsuMichael KelsenYong KimJonathan KingScott KippMichael KlempaAvi KligerCurtis KnittleShigeru KobayashiKeisuke KojimaPaul KolesarTom KolzeGlen KramerAlbert KuoHans

46、LacknerEfstathios LariosWayne LarsenRyan LatchmanMark LaubachGreg Le CheminantAndre Lessard7Copyright 2016 IEEE. All rights reserved.David LewisLei LiMike Peng LiShaohua LiThomas LichteneggerRu Jian LinRobert LingleJamesLiuZhenyu LiuWilliam LoMiklos LukacsKent LustedJeffery MakiJames MalkemusYonatan

47、 MalkimanEdwin MalletteArthur MarrisChris MashKirsten MatheusErdem MatogluLaurence MatolaThomas McDermottJohn McDonoughRichard MeiRichard MellitzLeo MontreuilPaul MooneyCharles MooreAndy MoorwoodThomas MuellerRon MuirDale MurrayHenry MuyshondtEdward NakamotoGary NichollPaul NikolichJohn NolanKevin N

48、ollRonald NordinMark NowellDavid OfeltIchiro OguraTom PalkertSujan PandeySesha PanguluriCarlos PardoMoon ParkPravin PatelPetar PepeljugoskiGerald PepperRuben Perez De ArandaAlonsoMichael PetersJohn PetrillaRick PimpinellaRainer PoehmererWilliam PowellRichard ProdanRick RabinovichSaifur RahmanAdee Ra

49、nRam RaoDuane RemeinVictor RenteriaMichael ResslPoldi (Pavlick) RimboimSalvatore RotoloHisaya SakamotoVineet SalunkeSam SambasivanYasuo SasakiFred SchindlerStefan SchneelePeter ScrutonAlexander SeigerNaoshi SerizawaMegha ShanbhagStephen ShellhammerBazhong ShenMizuki ShiraoKapil ShrikhandeJeff SlavickScott SommersYoshiaki SoneXiaolu SongBryan SparrowhawkEdward SpraguePeter StassarLeonard StencelKen-Ichi SuzukiSteve SwansonAndre SzczepanekWilliam SzetoBharat TailorAkio TajimaTakayuki TajimaTomoo TakaharaSatoshi TakahashiKiyoto TakahataAlexander TanToshiki TanakaBrian Teip