IEEE 379-2014 en Application of the Single-Failure Criterion to Nuclear Power Generating Station Safety Systems《核电站安全系统中单失效准则的应用》.pdf

《IEEE 379-2014 en Application of the Single-Failure Criterion to Nuclear Power Generating Station Safety Systems《核电站安全系统中单失效准则的应用》.pdf》由会员分享，可在线阅读，更多相关《IEEE 379-2014 en Application of the Single-Failure Criterion to Nuclear Power Generating Station Safety Systems《核电站安全系统中单失效准则的应用》.pdf（27页珍藏版）》请在麦多课文档分享上搜索。

1、 IEEE Standard for Application of the Single-Failure Criterion to Nuclear Power Generating Station Safety Systems Sponsored by the Nuclear Power Engineering Committee IEEE 3 Park Avenue New York, NY 10016-5997 USA IEEE Power and Energy Society IEEE Std 379-2014 (Revision of IEEE Std 379-2000) IEEE S

2、td 379-2014 (Revision of IEEE Std 379-2000) IEEE Standard for Application of the Single-Failure Criterion to Nuclear Power Generating Station Safety Systems Sponsor Nuclear Power Engineering Committee of the IEEE Power and Energy Society Approved 16 May 2014 IEEE-SA Standards Board Abstract: Require

3、ments for the application of the single-failure criterion to the electrical power, instrumentation, and control portions of nuclear power generating safety systems are provided in this standard. Keywords: actuator, cascaded failure, common-cause failure, design basis event, detectable failure, effec

4、ts analysis, IEEE 379, nondetectable failure, safety system, single-failure criterion, system actuation, system logic The Institute of Electrical and Electronics Engineers, Inc. 3 Park Avenue, New York, NY 10016-5997, USA Copyright 2014 by The Institute of Electrical and Electronics Engineers, Inc.

5、All rights reserved. Published 30 May 2014. Printed in the United States of America. IEEE is a registered trademark in the U.S. Patent fitness for a particular purpose; non-infringement; and quality, accuracy, effectiveness, currency, or completeness of material. In addition, IEEE disclaims any and

6、all conditions relating to: results; and workmanlike effort. IEEE standards documents are supplied “AS IS” and “WITH ALL FAULTS.” Use of an IEEE standard is wholly voluntary. The existence of an IEEE standard does not imply that there are no other ways to produce, test, measure, purchase, market, or

7、 provide other goods and services related to the scope of the IEEE standard. Furthermore, the viewpoint expressed at the time a standard is approved and issued is subject to change brought about through developments in the state of the art and comments received from users of the standard. In publish

8、ing and making its standards available, IEEE is not suggesting or rendering professional or other services for, or on behalf of, any person or entity nor is IEEE undertaking to perform any duty owed by any other person or entity to another. Any person utilizing any IEEE Standards document, should re

9、ly upon his or her own independent judgment in the exercise of reasonable care in any given circumstances or, as appropriate, seek the advice of a competent professional in determining the appropriateness of a given IEEE standard. IN NO EVENT SHALL IEEE BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL

10、, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO: PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR

11、OTHERWISE) ARISING IN ANY WAY OUT OF THE PUBLICATION, USE OF, OR RELIANCE UPON ANY STANDARD, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE AND REGARDLESS OF WHETHER SUCH DAMAGE WAS FORESEEABLE. Translations The IEEE consensus development process involves the review of documents in English only.

12、In the event that an IEEE standard is translated, only the English version published by IEEE should be considered the approved IEEE standard. Official statements A statement, written or oral, that is not processed in accordance with the IEEE-SA Standards Board Operations Manual shall not be consider

13、ed or inferred to be the official position of IEEE or any of its committees and shall not be considered to be, or be relied upon as, a formal position of IEEE. At lectures, symposia, seminars, or educational courses, an individual presenting information on IEEE standards shall make it clear that his

14、 or her views should be considered the personal views of that individual rather than the formal position of IEEE. Comments on standards Comments for revision of IEEE Standards documents are welcome from any interested party, regardless of membership affiliation with IEEE. However, IEEE does not prov

15、ide consulting information or advice pertaining to IEEE Standards documents. Suggestions for changes in documents should be in the form of a proposed change of text, together with appropriate supporting comments. Since IEEE standards represent a consensus of concerned interests, it is important that

16、 any responses to comments and questions also receive the concurrence of a balance of interests. For this reason, IEEE and the members of its societies and Standards Coordinating Committees are not able to provide an instant response to comments or questions except in those cases where the matter ha

17、s previously been addressed. For the same reason, IEEE does not respond to interpretation requests. Any person who would like to participate in revisions to an IEEE standard is welcome to join the relevant IEEE working group. Comments on standards should be submitted to the following address: Secret

18、ary, IEEE-SA Standards Board 445 Hoes Lane Piscataway, NJ 08854 USA Laws and regulations Users of IEEE Standards documents should consult all applicable laws and regulations. Compliance with the provisions of any IEEE Standards document does not imply compliance to any applicable regulatory requirem

19、ents. Implementers of the standard are responsible for observing or referring to the applicable regulatory requirements. IEEE does not, by the publication of its standards, intend to urge action that is not in compliance with applicable laws, and these documents may not be construed as doing so. Cop

20、yrights IEEE draft and approved standards are copyrighted by IEEE under U.S. and international copyright laws. They are made available by IEEE and are adopted for a wide variety of both public and private uses. These include both use, by reference, in laws and regulations, and use in private self-re

21、gulation, standardization, and the promotion of engineering practices and methods. By making these documents available for use and adoption by public authorities and private users, IEEE does not waive any rights in copyright to the documents. Photocopies Subject to payment of the appropriate fee, IE

22、EE will grant users a limited, non-exclusive license to photocopy portions of any individual standard for company or organizational internal use or individual, non-commercial use only. To arrange for payment of licensing fees, please contact Copyright Clearance Center, Customer Service, 222 Rosewood

23、 Drive, Danvers, MA 01923 USA; +1 978 750 8400. Permission to photocopy portions of any individual standard for educational classroom use can also be obtained through the Copyright Clearance Center. Updating of IEEE Standards documents Users of IEEE Standards documents should be aware that these doc

24、uments may be superseded at any time by the issuance of new editions or may be amended from time to time through the issuance of amendments, corrigenda, or errata. An official IEEE document at any point in time consists of the current edition of the document together with any amendments, corrigenda,

25、 or errata then in effect. Every IEEE standard is subjected to review at least every ten years. When a document is more than ten years old and has not undergone a revision process, it is reasonable to conclude that its contents, although still of some value, do not wholly reflect the present state o

26、f the art. Users are cautioned to check to determine that they have the latest edition of any IEEE standard. In order to determine whether a given document is the current edition and whether it has been amended through the issuance of amendments, corrigenda, or errata, visit the IEEE-SA Website at h

27、ttp:/ieeexplore.ieee.org/xpl/standards.jsp or contact IEEE at the address listed previously. For more information about the IEEE SA or IEEEs standards development process, visit the IEEE-SA Website at http:/standards.ieee.org. Errata Errata, if any, for all IEEE standards can be accessed on the IEEE

28、-SA Website at the following URL: http:/standards.ieee.org/findstds/errata/index.html. Users are encouraged to check this URL for errata periodically. Patents Attention is called to the possibility that implementation of this standard may require use of subject matter covered by patent rights. By pu

29、blication of this standard, no position is taken by the IEEE with respect to the existence or validity of any patent rights in connection therewith. If a patent holder or patent applicant has filed a statement of assurance via an Accepted Letter of Assurance, then the statement is listed on the IEEE

30、-SA Website at http:/standards.ieee.org/about/sasb/patcom/patents.html. Letters of Assurance may indicate whether the Submitter is willing or unwilling to grant licenses under patent rights without compensation or under reasonable rates, with reasonable terms and conditions that are demonstrably fre

31、e of any unfair discrimination to applicants desiring to obtain such licenses. Essential Patent Claims may exist for which a Letter of Assurance has not been received. The IEEE is not responsible for identifying Essential Patent Claims for which a license may be required, for conducting inquiries in

32、to the legal validity or scope of Patents Claims, or determining whether any licensing terms or conditions provided in connection with submission of a Letter of Assurance, if any, or in any licensing agreements are reasonable or non-discriminatory. Users of this standard are expressly advised that d

33、etermination of the validity of any patent rights, and the risk of infringement of such rights, is entirely their own responsibility. Further information may be obtained from the IEEE Standards Association. Participants At the time this IEEE standard was completed, the Safety Systems and Single-Fail

34、ure Criteria Working Group had the following membership: Royce Beacom, Chair Gary Johnson Michael H. Miller Frank Novak Tom Richard Edward Schindhelm David Theriault Michael Waterman David Zaprazny The following members of the individual balloting committee voted on this standard. Balloters may have

35、 voted for approval, disapproval, or abstention. Satish Aggarwal George Ballassi Royce Beacom William Bloethe Daniel Brosnan Robert Carruth Suresh Channarasappa Tom Crawford David Curbo John Disosway Wells Fargo Stephen Fleger Robert Fuld James Gleason Dale Goodney Randall Groves Ajit Gwal Daryl Har

36、mon Hamidreza Heidarisafa David Herrell Werner Hoelzl David Horvath Peter Hung Randy Jamison Ronald Jarrett Yuri Khersonsky Robert Konnik G Lang Benjamin Lanz Michael Lauxman Jang-Soo Lee Bruce Lord Greg Luri John Macdonald Omar Mazzoni John Mcalhaney Jr John Merando Sujeet Mishra Michael Newman War

37、ren Odess-Gillett Jan Pirrong Iulian Profir Ted Riccio Bartien Sayogo Glen Schinzel David Smith Robert Stark Gary Stoedter John Vergis Michael Waterman Kenneth White Yvonne Williams Tamatha Womack Paul Yanosy Copyright 2014 IEEE. All rights reserved. vi Copyright 2014 IEEE. All rights reserved. viiT

38、he Nuclear Power Engineering Committee (NPEC) that recommended approval of this standard had the following membership: George Ballassi, Chair James Parello, Vice Chair Steven Fleger, Secretary Ijaz Ahmad Dheya Al-Othmany George Attarian Farouk D. Baxter* Royce D. Beacom Mark D. Bowman Daniel F. Bros

39、nan Nissen M. Burstein Keith Bush Robert C. Carruth John P. Carter Suresh Channarasappa Dennis Dellinger David R. Desaulniers John Disosway Walter F. Emerson Stephen Fleger Robert J. Fletcher Robert Francis Robert B. Fuld David Gladey James F. Gleason Dale T. Goodney Robert Hall Kuljit Hara Daryl Ha

40、rmon David Herrell Dirk C. Hopp David A. Horvath Paul R. Johnson Christopher J. Kerr Bok-Ryul Kim Thomas Koshy James K. Liming Bruce A. Lord John D. MacDonald J. Scott Malcolm Alexander Marion* Michael H. Miller Edward R. Mohtashemi Yasushi Nakagawa Julius Persensky* Ted Riccio Mark F. Santschi Glen

41、 E. Schinzel Zdenko Simic James E. Stoner, Jr. Marek Tengler James E. Thomas Masafumi Utsumi Michael Waterman Edward Wenzinger John White Paul L. Yanosy, Sr. Won Yong Yun Dave J. Zaprazny Oon-Pyo Zhu * non-voting members When the IEEE-SA Standards Board approved this standard on 16 May 2014, it had

42、the following membership: John Kulick, Chair David J. Law, Vice Chair Richard H. Hulett, Past Chair Konstantinos Karachalios, Secretary Masayuki Ariyoshi Peter Balma Farooq Bari Ted Burse Wael William Diab Stephen Dukes Jean-Philippe Faure Alexander Gelman Mark Halpin Gary Hoffman Paul Houz Jim Hugh

43、es Michael Janezic Joseph L. Koepfinger* Oleg Logvinov Ron Petersen Gary Robinson Jon Walter Rosdahl Adrian Stephens Peter Sutherland Yatin Trivedi Phil Winston Yu Yuan *Member Emeritus Also included are the following nonvoting IEEE-SA Standards Board liaisons: Richard DeBlasio, DOE Representative M

44、ichael Janezic, NIST Representative Patrick Gibbons IEEE-SA Publishing Malia Zaman IEEE-SA Technical Community Programs Introduction This introduction is not part of IEEE Std 379-2014, IEEE Standard for Application of the Single-Failure Criterion to Nuclear Power Generating Station Safety Systems. T

45、he requirement for nuclear power generating station safety systems to meet a single-failure criterion is found in many documents, including IEEE Standards, American Nuclear Society (ANS) standards, and federal regulations. It is the intention of this document to Conform specifically with the require

46、ments of IEEE Std 603-2009a Interpret the single-failure criterion as stated in IEEE Std 603-2009 Provide guidance in the application of the single-failure criterion as stated in IEEE Std 603-2009 It is recognized that the single-failure criterion is applicable to the aggregate of electrical and mec

47、hanical systems. However, the criterion statement, as found in this document, has been developed for electrical systems. Where the interface with mechanical systems is unavoidable (e.g., sensing lines), the mechanical portions are considered to be part of the electrical system with which they interf

48、ace. It should be noted that the systems include the actuation and protection systems, as well as the sense, command, and execute features of the power system (in accordance with IEEE Std 741-2007, IEEE Standard Criteria for the Protection of Class 1E Power Systems and Equipment in Nuclear Power Gen

49、erating Stations. The purpose of this revision to the standard is to Update the references cited in the text The standard working group has reviewed and identified that “indispensable” references are indeed in Clause 2, as the latest IEEE style manual (2014) directs. The remaining references have been included in the Bibliography (Annex A). This was included as part of the updating process for the standard. Verify that the terms not identified in the definitions of this standard (3.1) are identified in the IEEE-SA Standards Definition Database. The activity provides