IEEE 1215-2013 en Guide for the Application of Separable Insulated Connectors《可分离的绝缘连接器的IEEE应用指南》.pdf

《IEEE 1215-2013 en Guide for the Application of Separable Insulated Connectors《可分离的绝缘连接器的IEEE应用指南》.pdf》由会员分享，可在线阅读，更多相关《IEEE 1215-2013 en Guide for the Application of Separable Insulated Connectors《可分离的绝缘连接器的IEEE应用指南》.pdf（49页珍藏版）》请在麦多课文档分享上搜索。

1、 IEEE Guide for the Application of Separable Insulated Connectors Sponsored by the Insulated Conductors Committee IEEE 3 Park Avenue New York, NY 10016-5997 USA IEEE Power and Energy SocietyIEEE Std 1215-2013(Revision ofIEEE Std 1215-2001) IEEE Std 1215-2013 (Revision of IEEE Std 1215-2001) IEEE Gui

2、de for the Application of Separable Insulated Connectors Sponsor Insulated Conductors Committee of the IEEE Power and Energy Society Approved 14 June 2013 IEEE-SA Standards Board Abstract: General information on the application and operation of separable connectors is provided in this guide. It is i

3、ntended to be basic and supplement the manufacturers specific recommendations and established utility practices. Keywords: deadbreak connector, elbow connector, IEEE 1215, loadbreak connector, power distribution systems, separable connector, separable insulated connector systems The Institute of Ele

4、ctrical and Electronics Engineers, Inc. 3 Park Avenue, New York, NY 10016-5997, USA Copyright 2013 by The Institute of Electrical and Electronics Engineers, Inc. All rights reserved. Published 12 July 2013. Printed in the United States of America. IEEE is a registered trademark in the U.S. Patent +1

5、 978 750 8400. Permission to photocopy portions of any individual standard for educational classroom use can also be obtained through the Copyright Clearance Center. Copyright 2013 IEEE. All rights reserved. iv Notice to users Laws and regulations Users of IEEE Standards documents should consult all

6、 applicable laws and regulations. Compliance with the provisions of any IEEE Standards document does not imply compliance to any applicable regulatory requirements. Implementers of the standard are responsible for observing or referring to the applicable regulatory requirements. IEEE does not, by th

7、e publication of its standards, intend to urge action that is not in compliance with applicable laws, and these documents may not be construed as doing so. Copyrights This document is copyrighted by the IEEE. It is made available for a wide variety of both public and private uses. These include both

8、 use, by reference, in laws and regulations, and use in private self-regulation, standardization, and the promotion of engineering practices and methods. By making this document available for use and adoption by public authorities and private users, the IEEE does not waive any rights in copyright to

9、 this document. Updating of IEEE documents Users of IEEE Standards documents should be aware that these documents may be superseded at any time by the issuance of new editions or may be amended from time to time through the issuance of amendments, corrigenda, or errata. An official IEEE document at

10、any point in time consists of the current edition of the document together with any amendments, corrigenda, or errata then in effect. In order to determine whether a given document is the current edition and whether it has been amended through the issuance of amendments, corrigenda, or errata, visit

11、 the IEEE-SA Website at http:/standards.ieee.org/index.html or contact the IEEE at the address listed previously. For more information about the IEEE Standards Association or the IEEE standards development process, visit IEEE-SA Website at http:/standards.ieee.org/index.html. Errata Errata, if any,

12、for this and all other standards can be accessed at the following URL: http:/standards.ieee.org/findstds/errata/index.html. Users are encouraged to check this URL for errata periodically. Patents Attention is called to the possibility that implementation of this standard may require use of subject m

13、atter covered by patent rights. By publication of this standard, no position is taken by the IEEE with respect to the existence or validity of any patent rights in connection therewith. If a patent holder or patent applicant has filed a statement of assurance via an Accepted Letter of Assurance, the

14、n the statement is listed on the IEEE-SA Website at http:/standards.ieee.org/about/sasb/patcom/patents.html. Letters of Assurance may indicate whether the Submitter is willing or unwilling to grant licenses under patent rights without compensation or under reasonable rates, with reasonable terms and

15、 conditions that are demonstrably free of any unfair discrimination to applicants desiring to obtain such licenses. Copyright 2013 IEEE. All rights reserved. v Essential Patent Claims may exist for which a Letter of Assurance has not been received. The IEEE is not responsible for identifying Essenti

16、al Patent Claims for which a license may be required, for conducting inquiries into the legal validity or scope of Patents Claims, or determining whether any licensing terms or conditions provided in connection with submission of a Letter of Assurance, if any, or in any licensing agreements are reas

17、onable or non-discriminatory. Users of this standard are expressly advised that determination of the validity of any patent rights, and the risk of infringement of such rights, is entirely their own responsibility. Further information may be obtained from the IEEE Standards Association. Copyright 20

18、13 IEEE. All rights reserved. vi Participants At the time this IEEE guide was completed, the Separable Connectors Application Guide Working Group had the following membership: Harry L. Hayes, III, Chair Edward M. Jankowich, Vice Chair Tom Champion Dave Crotty Mike Dyer Richard Harp Jeff Helzer David

19、 Hughes Mike Jackson Dan Kennedy Glenn Luzzi John Makal Ewell T. Robinson Michael Smalley Stanley Szyszko Tim Wall Carl Wentzel The following members of the individual balloting committee voted on this guide. Balloters may have voted for approval, disapproval, or abstention. John Ainscough Roy Alexa

20、nder Michael Bayer Kenneth Bow William Byrd Weijen Chen Jacques Cote Dave Crotty Frank Di Guglielmo Gary Donner Randall Dotson Dana Dufield Michael Faulkenberry Marcel Fortin George Gela Frank Gerleve David Gilmer Steven Graham Randall Groves Jerry Harness Richard Harp Jeffrey Hartenberger Wolfgan H

21、averkamp Lee Herron Werner Hoelzl David Horvath David Hughes Edward M. Jankowich A. Jones Gael Kennedy Yuri Khersonsky Morteza Khodaie Jim Kulchisky Asok Kumar Senthil Kumar Chung-Yiu Lam Benjamin Lanz Michael Lauxman Greg Luri Glenn Luzzi Ahmad Mahinfallah Arturo Maldonado William McBride Thomas Mc

22、Carthy Jerry Murphy Arthur Neubauer Michael S. Newman Lorraine Padden Donald Parker Serge Pelissou Iulian Profir Robert Resuali Michael Roberts Bartien Sayogo Ted Schoenberg Robert Seitz Gil Shultz Hyeong Sim Michael Smalley Jerry Smith Gregory Stano Gary Stoedter Peter Tirinzoni John Vergis Carl Wa

23、ll Daniel Ward Lee Welch Yingli Wen Carl Wentzel Kenneth White Tiebin Zhao Copyright 2013 IEEE. All rights reserved. vii When the IEEE-SA Standards Board approved this guide on 14 June 2013, it had the following membership: John Kulick, Chair David J. Law, Vice Chair Richard H. Hulett, Past Chair Ko

24、nstantinos Karachalios, Secretary Masayuki Ariyoshi Peter Balma Farooq Bari Ted Burse Wael William Diab Stephen Dukes Jean-Philippe Faure Alexander Gelman Mark Halpin Gary Hoffman Paul Houz Jim Hughes Michael Janezic Joseph L. Koepfinger* Oleg Logvinov Ron Petersen Gary Robinson Jon Walter Rosdahl A

25、drian Stephens Peter Sutherland Yatin Trivedi Phil Winston Yu Yuan *Member Emeritus Also included are the following nonvoting IEEE-SA Standards Board liaisons: Richard DeBlasio, DOE Representative Michael Janezic, NIST Representative Catherine Berger IEEE Standards Senior Program Manager, Document D

26、evelopment Malia Zaman IEEE Standards Program Manager, Technical Program Development Copyright 2013 IEEE. All rights reserved. viii Introduction This introduction is not part of IEEE Std 1215-2013, IEEE Guide for the Application of Separable Insulated Connectors. This guide is intended as a suppleme

27、nt to the training in high-voltage electrical equipment, established safe operating procedures, and the manufacturers instructions for the application of separable insulated connectors. Installers and operators of separable connectors require formal training in the use of high-voltage electrical equ

28、ipment. It is the users responsibility to establish safe operating procedures and provide training. The manufacturers are required to provide installation and operating instructions for their products. This document is the first revision to the original IEEE guide issued that addresses the applicati

29、on and operation of separable insulated connectors. This application guide is the product of close collaboration between representatives of both users and manufacturers of separable connectors. The separable connector working group of the Insulated Connector Committee provided valuable input to this

30、 guide. This application guide is intended to be used in concert with IEEE Std 386, IEE Standard for Separable Insulated Connector Systems for Power Distribution Systems Above 600 V. IEEE Std 386 defines the ratings, construction specifications, service conditions, and qualification tests for separa

31、ble insulated connectors. IMPORTANT NOTICE: This guide provides only general information on the application and operation of separable insulated connectors. Users of this guide are responsible for determining and complying with appropriate environmental, health, safety and security laws, regulations

32、, requirements and practices applicable to their location, systems, equipment, and operations. Copyright 2013 IEEE. All rights reserved. ix Contents 1. Overview 1 1.1 Scope . 1 2. Normative references 1 3. Definitions 2 3.1 Parts of a 200 A bushing 2 3.2 Parts of a bushing well . 3 3.3 Parts of an e

33、lbow . 3 3.4 Separable connectors . 3 3.5 Tools 4 3.6 General 4 4. Design considerations . 4 4.1 Systems 4 4.2 Environmental . 8 5. Construction and installation 9 5.1 Use of loadbreak versus deadbreak . 9 5.2 Grounding of components and shields 10 5.3 Lubrication .11 5.4 Tightening requirements .12

34、 5.5 Elbow / bushing assembly 13 5.6 Compression lugs .13 5.7 Solvents 14 5.8 Cleanliness (avoiding contamination) 15 5.9 Cable training .17 5.10 Clearances for operation .17 5.11 Operator/bushing location 18 5.12 Stacking 600 A and 900 A Elbows .18 6. Operation .19 6.1 Use of 200 A loadbreak versus

35、 200 A deadbreak .19 6.2 Capacitive test point .19 6.3 Deadbreak operating practices 20 6.4 Loadbreak operating practices 21 6.5 Switching 26 6.6 Fault duty 27 6.7 Use of accessories .28 6.8 Grounding accessories 34 6.9 Inspection of separable connectors .36 6.10 Shear bolt connectors 36 Annex A (in

36、formative) Bibliography 38 Copyright 2013 IEEE. All rights reserved. 1 IEEE Guide for the Application of Separable Insulated Connectors IMPORTANT NOTICE: IEEE Standards documents are not intended to ensure safety, health, or environmental protection, or ensure against interference with or from other

37、 devices or networks. Implementers of IEEE Standards documents are responsible for determining and complying with all appropriate safety, security, environmental, health, and interference protection practices and all applicable laws and regulations. This IEEE document is made available for use subje

38、ct to important notices and legal disclaimers. These notices and disclaimers appear in all publications containing this document and may be found under the heading “Important Notice” or “Important Notices and Disclaimers Concerning IEEE Documents.” They can also be obtained on request from IEEE or v

39、iewed at http:/standards.ieee.org/IPR/disclaimers.html. 1. Overview This guide covers the application of separable connectors, rated from 601 V to 35 kV (38 kV), 600 A and 900 A or less, for use on power distribution systems. Included are design considerations and guidelines for the construction, in

40、stallation, and operation of 200 A loadbreak connectors and for 200 and 600 A and 900 A deadbreak connectors. 1.1 Scope This guide provides general information on the application and operation of separable connectors. It is intended to be basic, and supplement the manufacturers specific recommendati

41、ons and established utility practices. 2. Normative references The following referenced documents are indispensable for the application of this document (i.e., they must be understood and used, so each referenced document is cited in text and its relationship to this document is explained). For date

42、d references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments or corrigenda) applies. IEEE Std 1215-2013 IEEE Guide for the Application of Separable Insulated Connectors Copyright 2013 IEEE. All rights reserved. 2 ANSI C

43、2, National Electrical Safety Code (NESC).1ASTM F 855, Standard Specifications for Temporary Protective Grounds to Be Used on De-energized Electric Power Lines and Equipment.2IEEE Std C62.22, IEEE Guide for the Application of Metal-Oxide Surge Arresters for Alternating-Current Systems.3,4IEEE Std 38

44、6, IEEE Standard for Separable Insulated Connector Systems for Power Distribution Systems Above 600 V. IEEE Std 592, IEEE Standard for Exposed Semiconducting Shields on High-Voltage Cable Joints and Separable Connectors. IEEE Std 516, IEEE Guide for Maintenance Methods on Energized Power-Lines. IEEE

45、 Std C62.22.1, IEEE Guide for the Connection of Surge Arresters to Protect Insulated, Shielded Electric Power Cable Systems. IEEE Std 1216, IEEE Guide for the Application of Faulted Circuit Indicators for 200A, Single-Phase Underground Residential Distribution. IEEE Std 1610, IEEE Guide for the Appl

46、ication of Faulted Circuit Indicators for 200/600A, Three-Phase Underground Distribution. NFPA 70, National Electrical Code (NEC), National Fire Protection Association.5Stepniak, Frank M., Test Report No. 81-17-8230, Thomas 200 A loadbreak, 200 A deadbreak, and 600 A or 900 A deadbreak. 3.5 Tools 3.

47、5.1 live-line tool: An insulating tool, typically made of fiberglass that is designed for use on, or in the vicinity of, high-voltage equipment. As used in the context IEEE Std 1215, the live-line tool additionally provides a means of mechanically attaching to and locking onto the pulling eye of a s

48、eparable connector and provides a means of transferring mechanical force between two or more points. Common names for live-line tools used to operate separable connectors include shotgun stick, switching stick, clamp stick, shotgun tool, etc. 3.5.2 probe wrench: A tool designed for use in installing

49、 the probe into the lug of a 200 A elbow. Some types include a mechanism for limiting the maximum torque applied during installation of the probe. 3.6 General 3.6.1 shipping cap: A plastic cover that is used during transport to prevent contamination of the mating interface and internal parts. A shipping cap is not designed for installation on an energized circuit. 4. Design considerations 4.1 Systems 4.1.1 Underground distribution systems Numerous types of distribution systems exist. In North America, the most common type of distribution system is the