IEC TS 62446-3-2017 Photovoltaic (PV) systems - Requirements for testing documentation and maintenance - Part 3 Photovoltaic modules and plants - Outdoor infrar.pdf

《IEC TS 62446-3-2017 Photovoltaic (PV) systems - Requirements for testing documentation and maintenance - Part 3 Photovoltaic modules and plants - Outdoor infrar.pdf》由会员分享，可在线阅读，更多相关《IEC TS 62446-3-2017 Photovoltaic (PV) systems - Requirements for testing documentation and maintenance - Part 3 Photovoltaic modules and plants - Outdoor infrar.pdf（42页珍藏版）》请在麦多课文档分享上搜索。

1、 IEC TS 62446-3 Edition 1.0 2017-06 TECHNICAL SPECIFICATION Photovoltaic (PV) systems Requirements for testing, documentation and maintenance Part 3: Photovoltaic modules and plants Outdoor infrared thermography IEC TS 62446-3:2017-06(en) colour inside THIS PUBLICATION IS COPYRIGHT PROTECTED Copyrig

2、ht 2017 IEC, Geneva, Switzerland All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either IEC or IECs member Nation

3、al Committee in the country of the requester. If you have any questions about IEC copyright or have an enquiry about obtaining additional rights to this publication, please contact the address below or your local IEC member National Committee for further information. IEC Central Office Tel.: +41 22

4、919 02 11 3, rue de Varemb Fax: +41 22 919 03 00 CH-1211 Geneva 20 infoiec.ch Switzerland www.iec.ch About the IEC The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes International Standards for all electrical, electronic and related tec

5、hnologies. About IEC publications The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the latest edition, a corrigenda or an amendment might have been published. IEC Catalogue - webstore.iec.ch/catalogue The stand-alone application for c

6、onsulting the entire bibliographical information on IEC International Standards, Technical Specifications, Technical Reports and other documents. Available for PC, Mac OS, Android Tablets and iPad. IEC publications search - www.iec.ch/searchpub The advanced search enables to find IEC publications by

7、 a variety of criteria (reference number, text, technical committee,). It also gives information on projects, replaced and withdrawn publications. IEC Just Published - webstore.iec.ch/justpublished Stay up to date on all new IEC publications. Just Published details all new publications released. Ava

8、ilable online and also once a month by email. Electropedia - www.electropedia.org The worlds leading online dictionary of electronic and electrical terms containing 20 000 terms and definitions in English and French, with equivalent terms in 16 additional languages. Also known as the International E

9、lectrotechnical Vocabulary (IEV) online. IEC Glossary - std.iec.ch/glossary 65 000 electrotechnical terminology entries in English and French extracted from the Terms and Definitions clause of IEC publications issued since 2002. Some entries have been collected from earlier publications of IEC TC 37

10、, 77, 86 and CISPR. IEC Customer Service Centre - webstore.iec.ch/csc If you wish to give us your feedback on this publication or need further assistance, please contact the Customer Service Centre: csciec.ch. IEC TS 62446-3 Edition 1.0 2017-06 TECHNICAL SPECIFICATION Photovoltaic (PV) systems Requi

11、rements for testing, documentation and maintenance Part 3: Photovoltaic modules and plants Outdoor infrared thermography INTERNATIONAL ELECTROTECHNICAL COMMISSION ICS 27.160 ISBN 978-2-8322-4290-2 Registered trademark of the International Electrotechnical Commission Warning! Make sure that you obtai

12、ned this publication from an authorized distributor. colour inside 2 IEC TS 62446-3:2017 IEC 2017 CONTENTS FOREWORD . 4 1 Scope 6 2 Normative references 6 3 Terms and definitions 7 4 Requirements of inspection equipment 9 4.1 General . 9 4.2 Minimum requirements for IR-cameras used for inspecting PV

13、 plants . 9 4.3 Requirements for photo cameras for documentation of the findings . 10 4.4 Requirements for equipment to record the ambient conditions 10 5 Inspection procedure . 11 5.1 General . 11 5.2 Visual inspection . 12 5.3 Environmental conditions 12 5.4 Imaging procedure 13 5.4.1 General . 13

14、 5.4.2 Using fast carriers for IR-camera, e.g. aerial drones 13 5.4.3 Emissivity 14 6 Software for evaluation 15 7 Evaluation . 15 7.1 General . 15 7.2 Evaluation of IR images 16 7.3 Thermal abnormalities 17 7.3.1 General . 17 7.3.2 Classes of abnormalities (CoA) 17 7.3.3 Abnormalities of PV modules

15、 . 17 7.3.4 Abnormalities of other BOS components 17 7.4 Projection of temperature differences to nominal irradiance 18 7.4.1 General . 18 7.4.2 Modules . 20 7.4.3 Other BOS components . 21 8 Inspection report . 21 (normative) Inspection procedure explanations 24 Annex A A.1 Geometric resolution of

16、the camera 24 A.2 Angle of view 24 A.3 Matrix for cell identification . 25 (normative) Qualification of personnel 27 Annex B(normative) Matrix for thermal abnormalities of PV modules 28 Annex C(informative) Polygon measurement as a method of evaluation 32 Annex D(informative) Beaufort scale . 34 Ann

17、ex E Bibliography 36 Figure 1 Impact of camera moving speed . 14 Figure 2 Dependence of the emissivity of glass on the angle of view 10 15 Figure 3 Examples of influence of wind (left) and cloud movement (right) on observed temperature pattern . 16 IEC TS 62446-3:2017 IEC 2017 3 Figure 4 Example inf

18、rared thermograms of a PV string combiner box with cables, contacts, fuses and switches before (left) and after (right) maintenance on a faulty contact 18 Figure 5 Graphic representation of the correction factor for temperature differences to nominal irradiance/load conditions as a function of the r

19、elative irradiance/load 19 Figure 6 Example of image reporting 23 Figure A.1 Geometric resolution of the IR camera 24 Figure A.2 Angle of view 25 Figure A.3 View for the designation of cell position, viewed from the front of a 60- cell module, with the junction box at the top (rear side) 26 Figure D

20、.1 Arithmetic mean value by polygon measurement 32 Figure D.2 Arithmetic mean and spot value by polygon measurement . 33 Table 1 Minimum requirements for IR-cameras 9 Table 2 Requirements for equipment to record the ambient conditions 11 Table 3 Required inspection conditions 12 Table 4 Allocation i

21、n classes of abnormalities 17 Table 5 Example correction factors for temperature differences to nominal load conditions based on formula above and Figure 5 . 20 Table E.1 Beaufort scale taken form World Meteorolgical Organization (www.wmo.int) and Royal Meteorological Society (www.rmets.org) . 34 4

22、IEC TS 62446-3:2017 IEC 2017 INTERNATIONAL ELECTROTECHNICAL COMMISSION _ PHOTOVOLTAIC (PV) SYSTEMS REQUIREMENTS FOR TESTING, DOCUMENTATION AND MAINTENANCE Part 3: Photovoltaic modules and plants Outdoor infrared thermography FOREWORD 1) The International Electrotechnical Commission (IEC) is a worldw

23、ide organization for standardization comprising all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and in addition to other act

24、ivities, IEC publishes International Standards, Technical Specifications, Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested in the subjec

25、t dealt with may participate in this preparatory work. International, governmental and non- governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for Standardization (ISO) in accordance with conditions dete

26、rmined by agreement between the two organizations. 2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international consensus of opinion on the relevant subjects since each technical committee has representation from all interested IEC National Commi

27、ttees. 3) IEC Publications have the form of recommendations for international use and are accepted by IEC National Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC Publications is accurate, IEC cannot be held responsible for the way in which

28、 they are used or for any misinterpretation by any end user. 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications transparently to the maximum extent possible in their national and regional publications. Any divergence between any IEC Publicati

29、on and the corresponding national or regional publication shall be clearly indicated in the latter. 5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity assessment services and, in some areas, access to IEC marks of conformity. IEC is not

30、responsible for any services carried out by independent certification bodies. 6) All users should ensure that they have the latest edition of this publication. 7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and members of its technica

31、l committees and IEC National Committees for any personal injury, property damage or other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC Pub

32、lications. 8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is indispensable for the correct application of this publication. 9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject o

33、f patent rights. IEC shall not be held responsible for identifying any or all such patent rights. The main task of IEC technical committees is to prepare International Standards. In exceptional circumstances, a technical committee may propose the publication of a technical specification when the req

34、uired support cannot be obtained for the publication of an International Standard, despite repeated efforts, or the subject is still under technical development or where, for any other reason, there is the future but no immediate possibility of an agreement on an International Standard. Technical sp

35、ecifications are subject to review within three years of publication to decide whether they can be transformed into International Standards. IEC TS 62446-3, which is a technical specification, has been prepared by IEC technical committee 82: Solar photovoltaic energy systems. IEC TS 62446-3:2017 IEC

36、 2017 5 The text of this technical specification is based on the following documents: Enquiry draft Report on voting 82/1188/DTS 82/1242A/RVDTS Full information on the voting for the approval of this technical specification can be found in the report on voting indicated in the above table. This docu

37、ment has been drafted in accordance with the ISO/IEC Directives, Part 2. A list of all parts in the IEC 62446 series, published under the general title Photovoltaic (PV) systems Requirements for testing, documentation and maintenance, can be found on the IEC website. The committee has decided that t

38、he contents of this publication will remain unchanged until the stability date indicated on the IEC website under “http:/webstore.iec.ch“ in the data related to the specific publication. At this date, the publication will be transformed into an International standard, reconfirmed, withdrawn, replace

39、d by a revised edition, or amended. A bilingual version of this publication may be issued at a later date. IMPORTANT The colour inside logo on the cover page of this publication indicates that it contains colours which are considered to be useful for the correct understanding of its contents. Users

40、should therefore print this document using a colour printer. 6 IEC TS 62446-3:2017 IEC 2017 PHOTOVOLTAIC (PV) SYSTEMS REQUIREMENTS FOR TESTING, DOCUMENTATION AND MAINTENANCE Part 3: Photovoltaic modules and plants Outdoor infrared thermography 1 Scope This part of IEC 62446 defines outdoor thermogra

41、phic (infrared) inspection of PV modules and plants in operation. The inspection can include cables, contacts, fuses, switches, inverters, and batteries. This inspection supports the preventive maintenance for fire protection, the availability of the system for power production, and the inspection o

42、f the quality of the PV modules. Included in this document are the requirements for the measurement equipment, ambient conditions, inspection procedure, inspection report, personnel qualification and a matrix for thermal abnormalities as a guideline for the inspection. This document defines outdoor

43、thermography on photovoltaic (PV) modules and Balance-of- system (BOS) components of PV power plants in operation, using passive techniques (standard system operating conditions under natural sunlight, without any external power or irradiation sources). IEC 60904-12-1 covers general methods for labo

44、ratory or production-line PV module thermographic imaging but not the specific details that are most relevant to outdoor imaging of operational power plants including BOS components. Two different levels of inspections are currently used: a) A simplified thermographic inspection. This is a limited i

45、nspection to verify that the PV modules and BOS components are functioning, with reduced requirements for the qualification of personnel. For example, during a basic commissioning of a PV plant. Authoritative conclusions regarding module quality are not possible with this inspection, and examples of

46、 abnormalities are provided to aid the inspector. b) A detailed thermographic inspection and analysis. This may include thermal signatures which differ from the examples provided, and therefore requires a deeper understanding of the thermal abnormalities. For example, it may be used for periodic ins

47、pections according to the IEC 62446 series and for trouble-shooting the cause of underperforming systems. Absolute temperature measurements may be made. An authorized expert in PV plants, together with thermography experts can perform the inspection. 2 Normative references The following documents ar

48、e referred to in the text in such a way that some or all of their content constitutes requirements of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. IEC 60050-131, Internat

49、ional Electrotechnical Vocabulary Part 131: Circuit theory IEC 60216-2, Electrical insulating materials Thermal endurance properties Part 2: Determination of thermal endurance properties of electrical insulating materials Choice of test criteria IEC 60216-5, Electrical insulating materials Thermal endurance properties Part 5: Determination of relative thermal endurance index (RTE) of an insulating material IEC TS 62446-3:2017 IEC 2017 7 IEC 6