IEC 62271-112-2013 High-voltage switchgear and controlgear - Part 112 Alternating current high-speed earthing switches for secondary arc extinction on transmiss.pdf

《IEC 62271-112-2013 High-voltage switchgear and controlgear - Part 112 Alternating current high-speed earthing switches for secondary arc extinction on transmiss.pdf》由会员分享，可在线阅读，更多相关《IEC 62271-112-2013 High-voltage switchgear and controlgear - Part 112 Alternating current high-speed earthing switches for secondary arc extinction on transmiss.pdf（56页珍藏版）》请在麦多课文档分享上搜索。

1、 IEC 62271-112 Edition 1.0 2013-08 INTERNATIONAL STANDARD NORME INTERNATIONALE High-voltage switchgear and controlgear Part 112: Alternating current high-speed earthing switches for secondary arc extinction on transmission lines Appareillage haute tension Partie 112: Sectionneurs de terre rapides co

2、urant alternatif pour lextinction de larc secondaire sur les lignes de transport IEC62271-112:2013 colourinsideTHIS PUBLICATION IS COPYRIGHT PROTECTED Copyright 2013 IEC, Geneva, Switzerland All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in

3、 any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either IEC or IECs member National Committee in the country of the requester. If you have any questions about IEC copyright or have an enquiry about obtaining additional righ

4、ts to this publication, please contact the address below or your local IEC member National Committee for further information. Droits de reproduction rservs. Sauf indication contraire, aucune partie de cette publication ne peut tre reproduite ni utilise sous quelque forme que ce soit et par aucun pro

5、cd, lectronique ou mcanique, y compris la photocopie et les microfilms, sans laccord crit de la CEI ou du Comit national de la CEI du pays du demandeur. Si vous avez des questions sur le copyright de la CEI ou si vous dsirez obtenir des droits supplmentaires sur cette publication, utilisez les coord

6、onnes ci-aprs ou contactez le Comit national de la CEI de votre pays de rsidence. IEC Central Office Tel.: +41 22 919 02 11 3, rue de Varemb Fax: +41 22 919 03 00 CH-1211 Geneva 20 infoiec.ch Switzerland www.iec.ch About the IEC The International Electrotechnical Commission (IEC) is the leading glob

7、al organization that prepares and publishes International Standards for all electrical, electronic and related technologies. About IEC publications The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the latest edition, a corrigenda or a

8、n amendment might have been published. Useful links: IEC publications search - www.iec.ch/searchpub The advanced search enables you to find IEC publications by a variety of criteria (reference number, text, technical committee,). It also gives information on projects, replaced and withdrawn publicat

9、ions. IEC Just Published - webstore.iec.ch/justpublished Stay up to date on all new IEC publications. Just Published details all new publications released. Available on-line and also once a month by email. Electropedia - www.electropedia.org The worlds leading online dictionary of electronic and ele

10、ctrical terms containing more than 30 000 terms and definitions in English and French, with equivalent terms in additional languages. Also known as the International Electrotechnical Vocabulary (IEV) on-line. Customer Service Centre - webstore.iec.ch/csc If you wish to give us your feedback on this

11、publication or need further assistance, please contact the Customer Service Centre: csciec.ch. A propos de la CEI La Commission Electrotechnique Internationale (CEI) est la premire organisation mondiale qui labore et publie des Normes internationales pour tout ce qui a trait llectricit, llectronique

12、 et aux technologies apparentes. A propos des publications CEI Le contenu technique des publications de la CEI est constamment revu. Veuillez vous assurer que vous possdez ldition la plus rcente, un corrigendum ou amendement peut avoir t publi. Liens utiles: Recherche de publications CEI - www.iec.c

13、h/searchpub La recherche avance vous permet de trouver des publications CEI en utilisant diffrents critres (numro de rfrence, texte, comit dtudes,). Elle donne aussi des informations sur les projets et les publications remplaces ou retires. Just Published CEI - webstore.iec.ch/justpublished Restez i

14、nform sur les nouvelles publications de la CEI. Just Published dtaille les nouvelles publications parues. Disponible en ligne et aussi une fois par mois par email. Electropedia - www.electropedia.org Le premier dictionnaire en ligne au monde de termes lectroniques et lectriques. Il contient plus de

15、30 000 termes et dfinitions en anglais et en franais, ainsi que les termes quivalents dans les langues additionnelles. Egalement appel Vocabulaire Electrotechnique International (VEI) en ligne. Service Clients - webstore.iec.ch/csc Si vous dsirez nous donner des commentaires sur cette publication ou

16、 si vous avez des questions contactez-nous: csciec.ch. IEC 62271-112 Edition 1.0 2013-08 INTERNATIONAL STANDARD NORME INTERNATIONALE High-voltage switchgear and controlgear Part 112: Alternating current high-speed earthing switches for secondary arc extinction on transmission lines Appareillage haut

17、e tension Partie 112: Sectionneurs de terre rapides courant alternatif pour lextinction de larc secondaire sur les lignes de transport INTERNATIONAL ELECTROTECHNICAL COMMISSION COMMISSION ELECTROTECHNIQUE INTERNATIONALE U ICS 29.130.10; 29.130.99 PRICE CODE CODE PRIX ISBN 978-2-8322-1009-3 Registere

18、d trademark of the International Electrotechnical Commission Marque dpose de la Commission Electrotechnique Internationale Warning! Make sure that you obtained this publication from an authorized distributor. Attention! Veuillez vous assurer que vous avez obtenu cette publication via un distributeur

19、 agr. colourinside 2 62271-112 IEC:2013 CONTENTS FOREWORD . 4 1 General 6 1.1 Scope 6 1.2 Normative references 6 2 Normal and special service conditions 6 3 Terms and definitions . 6 3.1 General terms . 6 3.2 Assemblies of switchgear and controlgear . 8 3.3 Parts of assemblies . 8 3.4 Switching devi

20、ces 8 3.5 Parts of switchgear and controlgear 8 3.6 Operation 8 3.7 Characteristics quantities 8 4 Ratings . 8 5 Design and construction . 10 6 Type tests 11 7 Routine tests 14 8 Guide to the selection of HSES 14 9 Information to be given with enquiries, tenders and orders . 14 10 Rules for transpor

21、t, storage, installation, operation and maintenance . 15 11 Safety . 15 Annex A (informative) Background information on the use of HSES . 16 Annex B (informative) Induced current and voltage conditions for other cases . 21 Figure 1 Explanation of a multi-phase auto-reclosing scheme 7 Figure 2 Timing

22、 chart of HSES and circuit-breakers . 9 Figure A.1 Single-line diagram of a power system 17 Figure A.2 Timing chart of the HSESs in relation to the transmission line circuit-breakers . 17 Figure A.3 Typical timing chart showing the time between fault initiation and a successful re-close of the trans

23、mission line circuit-breakers . 18 Figure B.1 System condition to explain successive fault . 22 Figure B.2 Example of waveforms of delayed current zero phenomena 22 Figure B.3 Typical test circuit for electromagnetic coupling test-duty of a HSES with delayed current zero crossings . 24 Figure B.4 Ty

24、pical test circuit for electrostatic coupling test-duty of HSES with delayed current zero crossings . 24 Table 1 Standardized values of rated induced currents and voltages . 10 Table 2 Items to be listed on nameplate of a HSES 11 Table A.1 Comparison of earthing switches 19 Table A.2 Comparison of a

25、 four-legged reactor and HSES . 20 Table B.1 Preferred values for single-phase earth fault with delayed current zero phenomena in the presence of a successive fault . 23 62271-112 IEC:2013 3 Table B.2 Preferred values for multi-phase earth faults in a double-circuit system . 25 Table B.3 Preferred v

26、alues for covering the cases of categories 0 and 1 25 4 62271-112 IEC:2013 INTERNATIONAL ELECTROTECHNICAL COMMISSION _ HIGH-VOLTAGE SWITCHGEAR AND CONTROLGEAR Part 112: Alternating current high-speed earthing switches for secondary arc extinction on transmission lines FOREWORD 1) The International E

27、lectrotechnical Commission (IEC) is a worldwide organization for standardization comprising all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international co-operation on all questions concerning standardization in the electrical and electronic fiel

28、ds. To this end and in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their preparation is entrusted to technical committees; any IEC

29、 National Committee interested in the subject dealt with may participate in this preparatory work. International, governmental and non-governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for Standardizati

30、on (ISO) in accordance with conditions determined by agreement between the two organizations. 2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international consensus of opinion on the relevant subjects since each technical committee has representa

31、tion from all interested IEC National Committees. 3) IEC Publications have the form of recommendations for international use and are accepted by IEC National Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC Publications is accurate, IEC cann

32、ot be held responsible for the way in which they are used or for any misinterpretation by any end user. 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications transparently to the maximum extent possible in their national and regional publication

33、s. Any divergence between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter. 5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity assessment services and, in some areas, acc

34、ess to IEC marks of conformity. IEC is not responsible for any services carried out by independent certification bodies. 6) All users should ensure that they have the latest edition of this publication. 7) No liability shall attach to IEC or its directors, employees, servants or agents including ind

35、ividual experts and members of its technical committees and IEC National Committees for any personal injury, property damage or other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and expenses arising out of the publication, use of, or reliance upon

36、, this IEC Publication or any other IEC Publications. 8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is indispensable for the correct application of this publication. 9) Attention is drawn to the possibility that some of the elements o

37、f this IEC Publication may be the subject of patent rights. IEC shall not be held responsible for identifying any or all such patent rights. International Standard IEC 62271-112 has been prepared by subcommittee 17A: High-voltage switchgear and controlgear, of IEC technical committee 17: Switchgear

38、and controlgear. The text of this standard is based on the following documents: FDIS Report on voting 17A/1042/FDIS 17A/1050/RVD Full information on the voting for the approval of this standard can be found in the report on voting indicated in the above table. This publication has been drafted in ac

39、cordance with the ISO/IEC Directives, Part 2. This International Standard should be read in conjunction with IEC 62271-1:2007, to which it refers and which is applicable unless otherwise specified. In order to simplify the indication of 62271-112 IEC:2013 5 corresponding requirements, the same numbe

40、ring of clauses and subclauses is used as in IEC 62271-1. Amendments to these clauses and subclauses are given under the same numbering, whilst additional subclauses, are numbered from 101. A list of all parts in the IEC 62271, published under the general title High-voltage switchgear and controlgea

41、r, can be found on the IEC website. The committee has decided that the contents of this publication will remain unchanged until the stability date indicated on the IEC web site under “http:/webstore.iec.ch“ in the data related to the specific publication. At this date, the publication will be reconf

42、irmed, withdrawn, replaced by a revised edition, or amended. IMPORTANT The colour inside logo on the cover page of this publication indicates that it contains colours which are considered to be useful for the correct understanding of its contents. Users should therefore print this document using a c

43、olour printer. 6 62271-112 IEC:2013 HIGH-VOLTAGE SWITCHGEAR AND CONTROLGEAR Part 112: Alternating current high-speed earthing switches for secondary arc extinction on transmission lines 1 General 1.1 Scope This part of IEC 62271 applies to a.c. high-speed earthing switches designed for indoor and ou

44、tdoor installation and for operation at service frequencies of 50 Hz and 60 Hz on systems having voltages of 550 kV and above. High-speed earthing switches described in this standard are intended to extinguish the secondary arc remaining after clearing faults on transmission lines by the circuit-bre

45、akers. 1.2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including

46、any amendments) applies. IEC 62271-1:2007, High-voltage switchgear and controlgear Part 1: Common specifications IEC 62271-100:2008, High-voltage switchgear and controlgear Part 100: Alternating-current circuit-breakers IEC 62271-102:2001, High-voltage switchgear and controlgear Part 102: Alternatin

47、g current disconnectors and earthing switches IEC 62271-203:2011, High-voltage switchgear and controlgear Part 203: Gas-insulated metal-enclosed switchgear for rated voltages above 52 kV 2 Normal and special service conditions Clause 2 of IEC 62271-1:2007 is applicable. 3 Terms and definitions For t

48、he purposes of this document, the terms and definitions given in Clause 3 of IEC 62271-1:2011, as well as the following apply. 3.1 General terms 3.1.101 secondary arc arc that remains at the faulted point after interruption of the short-circuit current fed by the network Note 1 to entry: This second

49、ary arc is supplied by electrostatic or electromagnetic induction from the adjacent healthy phases. 62271-112 IEC:2013 7 3.1.102 single-phase auto-reclosing scheme auto-reclosing scheme in which a faulted phase circuit is opened and automatically re-closed independently from the other phases 3.1.103 multi-phase auto-reclosing scheme auto-reclosing scheme applied to double circuit overhead lines in w