IEC 62148-18-2014 Fiber optic active components and devices - Package and interface standards - Part 18 40-Gbit s serial transmitter and receiver components for.pdf

《IEC 62148-18-2014 Fiber optic active components and devices - Package and interface standards - Part 18 40-Gbit s serial transmitter and receiver components for.pdf》由会员分享，可在线阅读，更多相关《IEC 62148-18-2014 Fiber optic active components and devices - Package and interface standards - Part 18 40-Gbit s serial transmitter and receiver components for.pdf（40页珍藏版）》请在麦多课文档分享上搜索。

1、 IEC 62148-18 Edition 1.0 2014-11 INTERNATIONAL STANDARD Fibre optic active components and devices Package and interface standards Part 18: 40-Gbit/s serial transmitter and receiver components for use with the LC connector interface IEC 62148-18:2014-11(en) THIS PUBLICATION IS COPYRIGHT PROTECTED Co

2、pyright 2014 IEC, Geneva, Switzerland All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either IEC or IECs member N

3、ational Committee in the country of the requester. If you have any questions about IEC copyright or have an enquiry about obtaining additional rights to this publication, please contact the address below or your local IEC member National Committee for further information. IEC Central Office Tel.: +4

4、1 22 919 02 11 3, rue de Varemb Fax: +41 22 919 03 00 CH-1211 Geneva 20 infoiec.ch Switzerland www.iec.ch About the IEC The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes International Standards for all electrical, electronic and relate

5、d technologies. About IEC publications The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the latest edition, a corrigenda or an amendment might have been published. IEC Catalogue - webstore.iec.ch/catalogue The stand-alone application

6、for consulting the entire bibliographical information on IEC International Standards, Technical Specifications, Technical Reports and other documents. Available for PC, Mac OS, Android Tablets and iPad. IEC publications search - www.iec.ch/searchpub The advanced search enables to find IEC publicatio

7、ns by a variety of criteria (reference number, text, technical committee,). It also gives information on projects, replaced and withdrawn publications. IEC Just Published - webstore.iec.ch/justpublished Stay up to date on all new IEC publications. Just Published details all new publications released

8、. Available online and also once a month by email. Electropedia - www.electropedia.org The worlds leading online dictionary of electronic and electrical terms containing more than 30 000 terms and definitions in English and French, with equivalent terms in 14 additional languages. Also known as the

9、International Electrotechnical Vocabulary (IEV) online. IEC Glossary - std.iec.ch/glossary More than 55 000 electrotechnical terminology entries in English and French extracted from the Terms and Definitions clause of IEC publications issued since 2002. Some entries have been collected from earlier

10、publications of IEC TC 37, 77, 86 and CISPR. IEC Customer Service Centre - webstore.iec.ch/csc If you wish to give us your feedback on this publication or need further assistance, please contact the Customer Service Centre: csciec.ch. IEC 62148-18 Edition 1.0 2014-11 INTERNATIONAL STANDARD Fibre opt

11、ic active components and devices Package and interface standards Part 18: 40-Gbit/s serial transmitter and receiver components for use with the LC connector interface INTERNATIONAL ELECTROTECHNICAL COMMISSION V ICS 33.180.20 PRICE CODE ISBN 978-2-8322-1923-2 Registered trademark of the International

12、 Electrotechnical Commission Warning! Make sure that you obtained this publication from an authorized distributor. 2 IEC 62148-18:2014 IEC 2014 CONTENTS FOREWORD . 4 INTRODUCTION . 6 1 Scope 7 2 Normative references 7 3 Terms, definitions and abbreviations . 7 3.1 Terms and definitions 7 3.2 Abbrevi

13、ations 7 4 Electromagnetic compatibility (EMC) requirements 8 5 Classification . 8 6 Specification of 40-Gbit/s serial transmitter component for LC connectors without thermo-electric cooler 8 6.1 General . 8 6.2 Electrical interface 8 6.2.1 General . 8 6.2.2 Numbering of electrical terminals . 8 6.2

14、.3 Electrical terminal assignment . 9 6.3 Outline and footprint . 11 6.3.1 Drawing of package outline 11 6.3.2 Drawing of footprint . 13 7 Specification of 40-Gbit/s serial transmitter component for LC connectors with thermo-electric cooler 14 7.1 General . 14 7.2 Electrical interface 14 7.2.1 Gener

15、al . 14 7.2.2 Numbering of electrical terminals . 15 7.2.3 Electrical terminal assignment . 16 7.3 Outline and footprint . 18 7.3.1 Drawing of package outline 18 7.3.2 Drawing of footprint . 20 8 Specification of 40-Gbit/s serial transmitter component for LC connectors with thermo-electric cooler an

16、d built-in driver 21 8.1 General . 21 8.2 Electrical interface 21 8.2.1 General . 21 8.2.2 Numbering of electrical terminals . 22 8.2.3 Electrical terminal assignment . 23 8.3 Outline and footprint . 25 8.3.1 Drawing of package outline 25 8.3.2 Drawing of footprint . 27 9 Specification of receiver c

17、omponent for LC connectors with PIN 28 9.1 General . 28 9.2 Electrical interface 28 9.2.1 General . 28 9.2.2 Numbering of electrical terminals . 29 9.2.3 Electrical terminal assignment . 29 9.3 Outline and footprint . 31 IEC 62148-18:2014 IEC 2014 3 9.3.1 Drawing of package outline 31 9.3.2 Drawing

18、of footprint . 33 Bibliography 35 Figure 1 Electrical terminal numbering assignments . 8 Figure 2 Block diagram 9 Figure 3 Package outline drawing 11 Figure 4 Recommended pattern layout for the PCB 13 Figure 5 Electrical terminal numbering assignments . 15 Figure 6 Block diagram 16 Figure 7 Package

19、outline . 18 Figure 8 Recommended pattern layout for the PCB 20 Figure 9 Electrical terminal numbering assignments . 22 Figure 10 Block diagram 23 Figure 11 Package outline . 25 Figure 12 Recommended pattern layout for the PCB 27 Figure 13 Electrical terminal numbering assignments . 29 Figure 14 Blo

20、ck diagram 29 Figure 15 Package outline . 31 Figure 16 Recommended pattern layout for the PCB 33 Table 1 Terminal function definitions 10 Table 2 Dimensions of the package outline 12 Table 3 Dimensions of the recommended pattern layout for the PCB . 14 Table 4 Terminal function definitions 17 Table

21、5 Dimensions of the package outline 19 Table 6 Dimensions of the recommended pattern layout for the PCB . 21 Table 7 Terminal function definitions 24 Table 8 Dimensions of the package outline 26 Table 9 Dimensions of the recommended pattern layout for the PCB . 28 Table 10 Terminal function definiti

22、ons 30 Table 11 Dimensions of the package outline 32 Table 12 Dimensions of the recommended pattern layout for the PCB . 34 4 IEC 62148-18:2014 IEC 2014 INTERNATIONAL ELECTROTECHNICAL COMMISSION _ FIBRE OPTIC ACTIVE COMPONENTS AND DEVICES PACKAGE AND INTERFACE STANDARDS Part 18: 40-Gbit/s serial tra

23、nsmitter and receiver components for use with the LC connector interface FOREWORD 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising all national electrotechnical committees (IEC National Committees). The object of IEC is to promote inte

24、rnational co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports, Publicly Available Specifications (PAS) and Guides (hereaft

25、er referred to as “IEC Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with may participate in this preparatory work. International, governmental and non- governmental organizations liaising with the IEC also partic

26、ipate in this preparation. IEC collaborates closely with the International Organization for Standardization (ISO) in accordance with conditions determined by agreement between the two organizations. 2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an

27、international consensus of opinion on the relevant subjects since each technical committee has representation from all interested IEC National Committees. 3) IEC Publications have the form of recommendations for international use and are accepted by IEC National Committees in that sense. While all r

28、easonable efforts are made to ensure that the technical content of IEC Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any misinterpretation by any end user. 4) In order to promote international uniformity, IEC National Committees undertake to apply

29、 IEC Publications transparently to the maximum extent possible in their national and regional publications. Any divergence between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter. 5) IEC itself does not provide any attestation of co

30、nformity. Independent certification bodies provide conformity assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any services carried out by independent certification bodies. 6) All users should ensure that they have the latest edition of this publi

31、cation. 7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and members of its technical committees and IEC National Committees for any personal injury, property damage or other damage of any nature whatsoever, whether direct or indirect,

32、or for costs (including legal fees) and expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC Publications. 8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is indispensable for the corr

33、ect application of this publication. 9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent rights. IEC shall not be held responsible for identifying any or all such patent rights. International Standard IEC 62148-18 has been prepared

34、by subcommittee 86C: Fibre optic systems and active devices, of IEC technical committee 86: Fibre optics. The text of this standard is based on the following documents: CDV Report on voting 86C/1227/CDV 86C/1273/RVC Full information on the voting for the approval of this standard can be found in the

35、 report on voting indicated in the above table. This publication has been drafted in accordance with the ISO/IEC Directives, Part 2. IEC 62148-18:2014 IEC 2014 5 A list of all parts in the IEC 62148 series, published under the general title Fibre optic active components and devices Package and inter

36、face standards, can be found on the IEC website. The committee has decided that the contents of this publication will remain unchanged until the stability date indicated on the IEC web site under “http:/webstore.iec.ch“ in the data related to the specific publication. At this date, the publication w

37、ill be reconfirmed, withdrawn, replaced by a revised edition, or amended. A bilingual version of this publication may be issued at a later date. 6 IEC 62148-18:2014 IEC 2014 INTRODUCTION Compact optical sub-assembly (OSA) modules for 40 Gbit/s are used to convert electrical signals into optical sign

38、als and vice-versa. This part of IEC 62148 covers the physical interface for 40-Gbit/s compact OSA modules. These modules are designed for use with the LC fibre optic connector specified in IEC 61754-20, and are intended to be applied to 40 Gbit/s or higher bit rate transceivers. IEC 62148-18:2014 I

39、EC 2014 7 FIBRE OPTIC ACTIVE COMPONENTS AND DEVICES PACKAGE AND INTERFACE STANDARDS Part 18: 40-Gbit/s serial transmitter and receiver components for use with the LC connector interface 1 Scope This part of IEC 62148 covers the 40-Gbit/s serial physical interface specification of transmitter and rec

40、eiver components for use with the LC connector interface. The purpose of this standard is to adequately specify the physical requirements of optical transmitters and receivers that will enable mechanical interchangeability of transmitters and receivers complying with this standard both at the PCB le

41、vel and for any panel-mounting requirement. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of

42、the referenced document (including any amendments) applies. IEC 62148-1, Fibre optic active components and devices Package and interface standards Part 1: General and guidance IEC Guide 107, Electromagnetic compatibility Guide to the drafting of electromagnetic compatibility publications 3 Terms, de

43、finitions and abbreviations For the purposes of this document, the following terms, definitions and abbreviations apply. 3.1 Terms and definitions 3.1.1 TOSA module optical module that converts electrical signals into optical signals and that is connected to an optical fibre 3.1.2 ROSA module optica

44、l module that converts optical signals into electrical signals and that is connected to an optical fibre 3.2 Abbreviations DML directly modulated laser diode EmwL external modulator with laser diode FPC flexible printed circuit LD laser diode OSA optical sub-assembly 8 IEC 62148-18:2014 IEC 2014 PCB

45、 printed circuit board PD photodiode ROSA receiver optical sub-assembly TOSA transmitter optical sub-assembly 4 Electromagnetic compatibility (EMC) requirements The components specified in this part of IEC 62148 shall comply with suitable requirements for electromagnetic compatibility (in terms of b

46、oth, emission and immunity), depending on the particular usage/environment in which they are intended to be installed or integrated. Guidance to the drafting of such EMC requirements is provided in IEC Guide 107. Guidance for electrostatic discharge (ESD) is still under study. 5 Classification The t

47、ransmitter and receiver components for the LC connector described in this standard are classified as type 1 according to the definitions of IEC 62148-1. 6 Specification of 40-Gbit/s serial transmitter component for LC connectors without thermo-electric cooler 6.1 General This clause specifies the ph

48、ysical requirements of a TOSA module that will enable mechanical interchangeability of modules complying with this standard, both for the PCB and for any panel mounting requirement. The vendor should design the FPC by considering electrical crosstalk and mechanical stress. 6.2 Electrical interface 6

49、.2.1 General The electrical interface in this standard defines only the basic functionality of each pin. 6.2.2 Numbering of electrical terminals Pin numbering assignments are shown in Figure 1. Package potential shall be specified by each vendor. Figure 1 Electrical terminal numbering assignments FPC 6 5 4 3 2 1 8 7 IEC IEC 62148-18:2014 IEC 2014 9 6.2.3 Electrical terminal assignment Electrical terminal assignment and terminal func