IEC 60601-2-33-2010 Medical electrical equipment - Part 2-33 Particular requirements for the basic safety and essential performance of magnetic resonance equipm.pdf

《IEC 60601-2-33-2010 Medical electrical equipment - Part 2-33 Particular requirements for the basic safety and essential performance of magnetic resonance equipm.pdf》由会员分享，可在线阅读，更多相关《IEC 60601-2-33-2010 Medical electrical equipment - Part 2-33 Particular requirements for the basic safety and essential performance of magnetic resonance equipm.pdf（224页珍藏版）》请在麦多课文档分享上搜索。

1、 IEC 60601-2-33Edition 3.0 2010-03INTERNATIONAL STANDARD NORME INTERNATIONALEMedical electrical equipment Part 2-33: Particular requirements for the basic safety and essential performance of magnetic resonance equipment for medical diagnosis Appareils lectromdicaux Partie 2-33: Exigences particulire

2、s pour la scurit de base et les performances essentielles des appareils rsonance magntique utiliss pour le diagnostic mdical IEC60601-2-33:2010 colourinsideTHIS PUBLICATION IS COPYRIGHT PROTECTED Copyright 2010 IEC, Geneva, Switzerland All rights reserved. Unless otherwise specified, no part of this

3、 publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either IEC or IECs member National Committee in the country of the requester. If you have any questions about IEC copyright or ha

4、ve an enquiry about obtaining additional rights to this publication, please contact the address below or your local IEC member National Committee for further information. Droits de reproduction rservs. Sauf indication contraire, aucune partie de cette publication ne peut tre reproduite ni utilise so

5、us quelque forme que ce soit et par aucun procd, lectronique ou mcanique, y compris la photocopie et les microfilms, sans laccord crit de la CEI ou du Comit national de la CEI du pays du demandeur. Si vous avez des questions sur le copyright de la CEI ou si vous dsirez obtenir des droits supplmentai

6、res sur cette publication, utilisez les coordonnes ci-aprs ou contactez le Comit national de la CEI de votre pays de rsidence. IEC Central Office 3, rue de Varemb CH-1211 Geneva 20 Switzerland Email: inmailiec.ch Web: www.iec.ch About the IEC The International Electrotechnical Commission (IEC) is th

7、e leading global organization that prepares and publishes International Standards for all electrical, electronic and related technologies. About IEC publications The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the latest edition, a c

8、orrigenda or an amendment might have been published. Catalogue of IEC publications: www.iec.ch/searchpub The IEC on-line Catalogue enables you to search by a variety of criteria (reference number, text, technical committee,). It also gives information on projects, withdrawn and replaced publications

9、. IEC Just Published: www.iec.ch/online_news/justpub Stay up to date on all new IEC publications. Just Published details twice a month all new publications released. Available on-line and also by email. Electropedia: www.electropedia.org The worlds leading online dictionary of electronic and electri

10、cal terms containing more than 20 000 terms and definitions in English and French, with equivalent terms in additional languages. Also known as the International Electrotechnical Vocabulary online. Customer Service Centre: www.iec.ch/webstore/custserv If you wish to give us your feedback on this pub

11、lication or need further assistance, please visit the Customer Service Centre FAQ or contact us: Email: csciec.ch Tel.: +41 22 919 02 11 Fax: +41 22 919 03 00 A propos de la CEI La Commission Electrotechnique Internationale (CEI) est la premire organisation mondiale qui labore et publie des normes i

12、nternationales pour tout ce qui a trait llectricit, llectronique et aux technologies apparentes. A propos des publications CEI Le contenu technique des publications de la CEI est constamment revu. Veuillez vous assurer que vous possdez ldition la plus rcente, un corrigendum ou amendement peut avoir

13、t publi. Catalogue des publications de la CEI: www.iec.ch/searchpub/cur_fut-f.htm Le Catalogue en-ligne de la CEI vous permet deffectuer des recherches en utilisant diffrents critres (numro de rfrence, texte, comit dtudes,). Il donne aussi des informations sur les projets et les publications retires

14、 ou remplaces. Just Published CEI: www.iec.ch/online_news/justpub Restez inform sur les nouvelles publications de la CEI. Just Published dtaille deux fois par mois les nouvelles publications parues. Disponible en-ligne et aussi par email. Electropedia: www.electropedia.org Le premier dictionnaire en

15、 ligne au monde de termes lectroniques et lectriques. Il contient plus de 20 000 termes et dfinitions en anglais et en franais, ainsi que les termes quivalents dans les langues additionnelles. Egalement appel Vocabulaire Electrotechnique International en ligne. Service Clients: www.iec.ch/webstore/c

16、ustserv/custserv_entry-f.htm Si vous dsirez nous donner des commentaires sur cette publication ou si vous avez des questions, visitez le FAQ du Service clients ou contactez-nous: Email: csciec.ch Tl.: +41 22 919 02 11 Fax: +41 22 919 03 00 IEC 60601-2-33Edition 3.0 2010-03INTERNATIONAL STANDARD NORM

17、E INTERNATIONALEMedical electrical equipment Part 2-33: Particular requirements for the basic safety and essential performance of magnetic resonance equipment for medical diagnosis Appareils lectromdicaux Partie 2-33: Exigences particulires pour la scurit de base et les performances essentielles des

18、 appareils rsonance magntique utiliss pour le diagnostic mdical INTERNATIONAL ELECTROTECHNICAL COMMISSION COMMISSION ELECTROTECHNIQUE INTERNATIONALE XEICS 11.040.55 PRICE CODECODE PRIXISBN 2-8318-1081-8 Registered trademark of the International Electrotechnical Commission Marque dpose de la Commissi

19、on Electrotechnique Internationale colourinside 2 60601-2-33 IEC:2010 CONTENTS FOREWORD.54 INTRODUCTION.6H6H7 201.1 Scope, object and related standards .7H7H8 201.2 Normative references8H8H9 201.3 Terms and definitions 9H9H10 201.4 General requirements . 10H10H15 201.5 General requirements for testi

20、ng of ME EQUIPMENT 11H11H15 201.6 Classification of ME EQUIPMENT and ME SYSTEMS 12H12H15 201.7 ME EQUIPMENT identification, marking and documents . 13H13H16 201.8 Protection against electrical HAZARDS from ME EQUIPMENT . 14H14H27 201.9 Protection against mechanical HAZARDs of ME EQUIPMENT and ME SYS

21、TEMS 15H15H28 201.10 Protection against unwanted and excessive radiation HAZARDS . 16H16H28 201.11 Protection against excessive temperatures and other HAZARDS . 17H17H28 201.12 Accuracy of controls and instruments and protection against hazardous outputs .18H18H29 201.13 HAZARDOUS SITUATIONS and fau

22、lt conditions 19H19H47 201.14 PROGRAMMABLE ELECTRICAL MEDICAL SYSTEM (PEMS). 20H20H47 201.15 Construction of ME EQUIPMENT. 21H21H47 201.16 ME SYSTEMS 22H22H47 201.17 Electromagnetic compatibility of ME EQUIPMENT and ME SYSTEMS . 23H23H47 202 Electromagnetic compatibility Requirements and tests . 24H

23、24H48 Annexes . 25H25H48 Annex D (informative) Symbols on marking 26H26H49 Annex AA (informative) Particular guidance and rationale 27H27H51 Bibliography 28H28H96 Index of defined terms used in this particular standard 29H29H104 Figure 201.101 Gradient waveform and EFFECTIVE STIMULUS DURATION . 30H3

24、0H11 Figure 201.102 Limits for cardiac and peripheral nerve stimulation 31H31H33 Figure 201.103 Reduction of WHOLE BODY SAR limits at high temperatures 32H32H37 Figure 201.104 Volume for determining the spatial maximum of gradient output 33H33H43 Figure 201.105 Volume for determining the B1stray fie

25、ld 34H34H46 Figure 201.D.101 Signs indicating a transmit only RF coil, transmit / receive RF coil and a receive only RF coil. 35H35H50 Figure AA.1 Static magnetic fields: flow potentials and retardation. 36H36H68 Figure AA.2 Experimental data on PNS threshold of human volunteers in WHOLE BODY MR EQU

26、IPMENT. 37H37H83 Figure AA.3 Double logarithmic plot of experimental threshold values for peripheral nerve stimulation 38H38H84 Figure AA.4 Response value R(t) generated by convolution of a rectangular stimulus dB/dt and a nerve impulse response function n(t-). 39H39H88 Figure AA.5 Gradient waveform

27、 G, stimulus waveform dB/dt and response value R, for a trapezoid EPI waveform starting at t = 0 . 40H40H89 60601-2-33 IEC:2010 3 Figure AA.6 Threshold values dB/dt for two gradient waveforms, plotted against EFFECTIVE STIMULUS DURATION . 41H41H89 Figure AA.7 Threshold value of dB/dt for a sinusoid

28、gradient waveform, as function of the number of half periods in the waveform. 42H42H90 Figure AA.8 SAR limits for the exposed mass of a PATIENT 43H43H93 Table 201.101 List of symbols 44H44H15 Table 201.102 Rheobase values per type of gradient system. 45H45H32 Table 201.103 Weight factors for summati

29、on of the maximum output Oiper GRADIENT UNIT .46H46H34 Table 201.104 Temperature limits 47H47H34 Table 201.105 SAR limits for volume transmit coils . 48H48H35 Table 201.106 SAR limits for local transmit coils . 49H49H36 Table 201.D.101 Examples of warning signs and prohibitive signs):. 50H50H49 Tabl

30、e AA.1 Static field occupational standards. 51H51H67 4 60601-2-33 IEC:2010 INTERNATIONAL ELECTROTECHNICAL COMMISSION _ MEDICAL ELECTRICAL EQUIPMENT Part 2-33: Particular requirements for the basic safety and essential performance of magnetic resonance equipment for medical diagnosis FOREWORD 1) The

31、International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international co-operation on all questions concerning standardization in the electrical and

32、electronic fields. To this end and in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their preparation is entrusted to technical comm

33、ittees; any IEC National Committee interested in the subject dealt with may participate in this preparatory work. International, governmental and non-governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely with the International Organization fo

34、r Standardization (ISO) in accordance with conditions determined by agreement between the two organizations. 2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international consensus of opinion on the relevant subjects since each technical committee

35、 has representation from all interested IEC National Committees. 3) IEC Publications have the form of recommendations for international use and are accepted by IEC National Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC Publications is acc

36、urate, IEC cannot be held responsible for the way in which they are used or for any misinterpretation by any end user. 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications transparently to the maximum extent possible in their national and regio

37、nal publications. Any divergence between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter. 5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity assessment services and, in

38、some areas, access to IEC marks of conformity. IEC is not responsible for any services carried out by independent certification bodies. 6) All users should ensure that they have the latest edition of this publication. 7) No liability shall attach to IEC or its directors, employees, servants or agent

39、s including individual experts and members of its technical committees and IEC National Committees for any personal injury, property damage or other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and expenses arising out of the publication, use of, o

40、r reliance upon, this IEC Publication or any other IEC Publications. 8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is indispensable for the correct application of this publication. 9) Attention is drawn to the possibility that some of

41、 the elements of this IEC Publication may be the subject of patent rights. IEC shall not be held responsible for identifying any or all such patent rights. International standard IEC 60601-2-33 has been prepared by IEC subcommittee 62B: Diagnostic imaging equipment, of IEC technical committee 62: El

42、ectrical equipment in medical practice. This third edition cancels and replaces the second edition published in 2002, its Amendment 1 (2005) and Amendment 2 (2007) and constitutes a technical revision. This third edition of IEC 60601-2-33 is based on the second amendment to Edition 2. It has also be

43、en adapted to the third edition of IEC 60601-1 (2005), with technical modifications being introduced where appropriate. 60601-2-33 IEC:2010 5 The text of this particular standard is based on the following documents: FDIS Report on voting 62B/777/FDIS 62B/782/RVDFull information on the voting for the

44、 approval of this particular standard can be found in the report on voting indicated in the above table. This publication has been drafted in accordance with the ISO/IEC Directives, Part 2. In this standard, the following print types are used: Requirements and definitions: roman type. Test specifica

45、tions: italic type. Informative material appearing outside of tables, such as notes, examples and references: in smaller type. Normative text of tables is also in a smaller type. TERMS DEFINED IN CLAUSE 3 OF THE GENERAL STANDARD, IN THIS PARTICULAR STANDARD OR AS NOTED: SMALL CAPITALS. In referring

46、to the structure of this standard, the term “clause” means one of the seventeen numbered divisions within the table of contents, inclusive of all subdivisions (e.g. Clause 7 includes subclauses 7.1, 7.2, etc.); “subclause” means a numbered subdivision of a clause (e.g. 7.1, 7.2 and 7.2.1 are all sub

47、clauses of Clause 7). References to clauses within this standard are preceded by the term “Clause” followed by the clause number. References to subclauses within this particular standard are by number only. In this standard, the conjunctive “or” is used as an “inclusive or” so a statement is true if

48、 any combination of the conditions is true. The verbal forms used in this standard conform to usage described in Annex H of the ISO/IEC Directives, Part 2. For the purposes of this standard, the auxiliary verb: “shall” means that compliance with a requirement or a test is mandatory for compliance wi

49、th this standard; “should” means that compliance with a requirement or a test is recommended but is not mandatory for compliance with this standard; “may” is used to describe a permissible way to achieve compliance with a requirement or test. An asterisk (*) as the first character of a title or at the beginning of a paragraph or table title indicates that there is guid