IEC TS 62872-2015 Industrial-process measurement control and automation system interface between industrial facilities and the smart grid《工业设施和智能电网之间的工业过程测量 控制和自动化系统接口》.pdf

《IEC TS 62872-2015 Industrial-process measurement control and automation system interface between industrial facilities and the smart grid《工业设施和智能电网之间的工业过程测量 控制和自动化系统接口》.pdf》由会员分享，可在线阅读，更多相关《IEC TS 62872-2015 Industrial-process measurement control and automation system interface between industrial facilities and the smart grid《工业设施和智能电网之间的工业过程测量 控制和自动化系统接口》.pdf（68页珍藏版）》请在麦多课文档分享上搜索。

1、 IEC TS 62872 Edition 1.0 2015-12 TECHNICAL SPECIFICATION Industrial-process measurement, control and automation system interface between industrial facilities and the smart grid IEC TS 62872:2015-12(en) colour inside THIS PUBLICATION IS COPYRIGHT PROTECTED Copyright 2015 IEC, Geneva, Switzerland Al

2、l rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either IEC or IECs member National Committee in the country of the

3、requester. If you have any questions about IEC copyright or have an enquiry about obtaining additional rights to this publication, please contact the address below or your local IEC member National Committee for further information. IEC Central Office Tel.: +41 22 919 02 11 3, rue de Varemb Fax: +41

4、 22 919 03 00 CH-1211 Geneva 20 infoiec.ch Switzerland www.iec.ch About the IEC The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes International Standards for all electrical, electronic and related technologies. About IEC publications T

5、he technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the latest edition, a corrigenda or an amendment might have been published. IEC Catalogue - webstore.iec.ch/catalogue The stand-alone application for consulting the entire bibliographica

6、l information on IEC International Standards, Technical Specifications, Technical Reports and other documents. Available for PC, Mac OS, Android Tablets and iPad. IEC publications search - www.iec.ch/searchpub The advanced search enables to find IEC publications by a variety of criteria (reference n

7、umber, text, technical committee,). It also gives information on projects, replaced and withdrawn publications. IEC Just Published - webstore.iec.ch/justpublished Stay up to date on all new IEC publications. Just Published details all new publications released. Available online and also once a month

8、 by email. Electropedia - www.electropedia.org The worlds leading online dictionary of electronic and electrical terms containing more than 30 000 terms and definitions in English and French, with equivalent terms in 15 additional languages. Also known as the International Electrotechnical Vocabular

9、y (IEV) online. IEC Glossary - std.iec.ch/glossary More than 60 000 electrotechnical terminology entries in English and French extracted from the Terms and Definitions clause of IEC publications issued since 2002. Some entries have been collected from earlier publications of IEC TC 37, 77, 86 and CI

10、SPR. IEC Customer Service Centre - webstore.iec.ch/csc If you wish to give us your feedback on this publication or need further assistance, please contact the Customer Service Centre: csciec.ch. IEC TS 62872 Edition 1.0 2015-12 TECHNICAL SPECIFICATION Industrial-process measurement, control and auto

11、mation system interface between industrial facilities and the smart grid INTERNATIONAL ELECTROTECHNICAL COMMISSION ICS 25.040.40; 29.240.99; 35.100.05 ISBN 978-2-8322-3044-2 Registered trademark of the International Electrotechnical Commission Warning! Make sure that you obtained this publication fr

12、om an authorized distributor. colour inside 2 IEC TS 62872:2015 IEC 2015 CONTENTS FOREWORD . 5 INTRODUCTION . 7 1 Scope 8 2 Normative references 8 3 Terms and definitions 9 3.1 General . 9 3.2 Models in automation 10 3.3 Models in energy management system and smart grid 11 4 Abbreviations 13 5 Requi

13、rements 14 5.1 General . 14 5.2 Architecture requirements . 15 5.2.1 General . 15 5.2.2 Energy management in industrial facilities . 17 5.3 System interface model between facility and smart grid 20 5.4 Security requirements . 21 5.5 Safety requirements 22 5.6 Communication requirements 22 5.6.1 Gene

14、ral . 22 5.6.2 Use of common communications technology 22 5.6.3 Communication security requirements . 22 5.6.4 Network availability 22 5.6.5 Time synchronization . 23 5.7 Audit logging requirements . 23 5.8 Information requirements 23 5.8.1 General . 23 5.8.2 Information attributes . 23 Annex A (inf

15、ormative) User stories and use cases . 30 A.1 General . 30 A.2 User stories 30 A.3 Use cases . 32 A.3.1 Use case analysis 32 A.3.2 Actor names and roles . 33 A.3.3 Use case descriptions 34 Annex B (informative) An application example of demand response energy management model 47 B.1 General . 47 B.2

16、 Main architecture 47 B.3 Structure of a task 48 B.4 Approaches of energy management 48 B.4.1 General . 48 B.4.2 Approach 1 49 B.4.3 Approach 2 49 B.5 Mapping industrial demand response energy management model to use cases 49 Annex C (normative) Security services . 51 IEC TS 62872:2015 IEC 2015 3 An

17、nex D (informative) Solutions for information requirement 52 D.1 General . 52 D.2 Existing standards 52 D.3 Analysis for each use case . 53 D.3.1 General . 53 D.3.2 Analysis of “OpenADR2.0b“ . 53 D.3.3 Analysis of “OASIS Energy Interoperation 1.0“ 56 D.3.4 Analysis of “NAESB Energy Services Provider

18、 Interface (ESPI)“ 57 D.3.5 Analysis of “ISO/WD 17800 Facility Smart Grid Information Model” (FSGIM) 59 D.3.6 Analysis of “SEP 2.0 (IEEE P2030.5)“ . 61 Bibliography 62 Figure 1 Overview of interface between FEMS and smart grid . 15 Figure 2 Example facility electric power distribution . 16 Figure 3

19、Facility enterprise and control systems . 17 Figure 4 Model elements 18 Figure 5 Model architecture: (a) main architecture, (b) task structure . 19 Figure 6 Network architecture model 21 Figure A.1 Generic communication diagram between the smart grid and the FEMS . 33 Figure A.2 Sequence diagram for

20、 FG-100 36 Figure A.3 Sequence diagram for FG-200 38 Figure A.4 Sequence diagram for FG-300 40 Figure A.5 Sequence diagram for FG-400 42 Figure A.6 Sequence diagram for FG-500 43 Figure A.7 Sequence diagram for FG-600 44 Figure A.8 Sequence diagram for FG-700 46 Figure B.1 An application example of

21、demand response energy management model 47 Figure B.2 Structure of water cooling task 48 Figure D.1 Interaction to register report . 54 Figure D.2 Interaction to request report 54 Figure D.3 Simple setup exchange . 55 Table 1 Required information . 24 Table A.1 Facility user stories: facility manage

22、r view points . 31 Table A.2 Utility user stories: utility operator view points 31 Table A.3 Dependency between user stories and use cases 32 Table A.4 Actors and roles . 34 Table A.5 Exchanged information in FG-100 37 Table A.6 Exchanged information in FG-200 39 Table A.7 Exchanged information in F

23、G-300 41 Table A.8 Exchanged information in FG-400 42 Table A.9 Exchanged information in FG-500 43 Table A.10 Exchanged information in FG-600 45 4 IEC TS 62872:2015 IEC 2015 Table A.11 Exchanged information in FG-700 46 Table D.1 Overview of existing standard applicability . 52 Table D.2 “ADR2.0b“ a

24、pplicability 53 Table D.3 “OASIS Energy Interoperation 1.0“ applicability . 56 Table D.4 “NAESB Energy Services Provider Interface (ESPI)“ applicability 58 Table D.5 “ISO/WD 17800 Facility Smart Grid Information Model“ applicability 60 Table D.6 “SEP 2.0 (IEEE P2030.5)“ Applicability 61 IEC TS 62872

25、:2015 IEC 2015 5 INTERNATIONAL ELECTROTECHNICAL COMMISSION _ INDUSTRIAL-PROCESS MEASUREMENT, CONTROL AND AUTOMATION SYSTEM INTERFACE BETWEEN INDUSTRIAL FACILITIES AND THE SMART GRID FOREWORD 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization compri

26、sing all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and in addition to other activities, IEC publishes International Standa

27、rds, Technical Specifications, Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with may participate in this prepar

28、atory work. International, governmental and non- governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for Standardization (ISO) in accordance with conditions determined by agreement between the two organiz

29、ations. 2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international consensus of opinion on the relevant subjects since each technical committee has representation from all interested IEC National Committees. 3) IEC Publications have the form of

30、 recommendations for international use and are accepted by IEC National Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any misinterpretation

31、 by any end user. 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications transparently to the maximum extent possible in their national and regional publications. Any divergence between any IEC Publication and the corresponding national or region

32、al publication shall be clearly indicated in the latter. 5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any services carried out by

33、 independent certification bodies. 6) All users should ensure that they have the latest edition of this publication. 7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and members of its technical committees and IEC National Committees fo

34、r any personal injury, property damage or other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC Publications. 8) Attention is drawn to the Nor

35、mative references cited in this publication. Use of the referenced publications is indispensable for the correct application of this publication. 9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent rights. IEC shall not be held resp

36、onsible for identifying any or all such patent rights. The main task of IEC technical committees is to prepare International Standards. In exceptional circumstances, a technical committee may propose the publication of a technical specification when the required support cannot be obtained for the pu

37、blication of an International Standard, despite repeated efforts, or the subject is still under technical development or where, for any other reason, there is the future but no immediate possibility of an agreement on an International Standard. Technical specifications are subject to review within t

38、hree years of publication to decide whether they can be transformed into International Standards. IEC TS 62872, which is a technical specification, has been prepared by IEC technical committee 65: Industrial-process measurement, control and automation. 6 IEC TS 62872:2015 IEC 2015 The text of this t

39、echnical specification is based on the following documents: Enquiry draft Report on voting 65/590/DTS 65/598/RVC Full information on the voting for the approval of this technical specification can be found in the report on voting indicated in the above table. This publication has been drafted in acc

40、ordance with the ISO/IEC Directives, Part 2. A review of this Technical Specification will be carried out not later than 3 years after its publication with the options of: extension for another 3 years; conversion into an International Standard; or withdrawal.” The committee has decided that the con

41、tents of this publication will remain unchanged until the stability date indicated on the IEC website under “http:/webstore.iec.ch“ in the data related to the specific publication. At this date, the publication will be transformed into an International standard, reconfirmed, withdrawn, replaced by a

42、 revised edition, or amended. A bilingual version of this publication may be issued at a later date. IMPORTANT The colour inside logo on the cover page of this publication indicates that it contains colours which are considered to be useful for the correct understanding of its contents. Users should

43、 therefore print this document using a colour printer. IEC TS 62872:2015 IEC 2015 7 INTRODUCTION The World Energy Outlook 2013 13 1reported that industry consumed over 40 % of world electricity generation in 2011. Furthermore, industry itself is a significant generator of internal power, with many f

44、acilities increasingly implementing their own generation, co-generation and energy storage resources. As a major energy consumer, the ability of some industries to schedule their consumption can be used to minimize peak demands on the electrical grid. As an energy supplier, industries with in-house

45、generation or storage resources can also assist in grid load management. While some larger industrial facilities already manage their use and supply of electric power, more widespread deployment, especially by smaller facilities, will depend upon the availability of a readily available standard inte

46、rface between industrial automation equipment and the “smart grid”. NOTE In this document “smart grid” is used to refer to the external-to-industry entity with which industry interacts for the purpose of energy management. In other documents this term may be used to refer to all of the elements, inc

47、luding internal industrial energy elements, which work together to optimize energy generation and use. Standards are already being developed for home and building automation interfaces to the grid; however the requirements for industrial facilities differ significantly and are addressed in this Tech

48、nical Specification. Specifically excluded from the scope of this Technical Specification are the protocols needed for the direct control of energy resources within a facility where the control and ultimate liability for such control is delegated by the industrial facility to the external entity. 1N

49、umbers in square brackets refer to the bibliography. 8 IEC TS 62872:2015 IEC 2015 INDUSTRIAL-PROCESS MEASUREMENT, CONTROL AND AUTOMATION SYSTEM INTERFACE BETWEEN INDUSTRIAL FACILITIES AND THE SMART GRID 1 Scope This Technical Specification defines the interface, in terms of information flow, between industrial facilities and the “smart grid”. It identifies, profiles and extends where required, the standards needed to allow t