IEC 62642-2-4-2010 Alarm systems - Intrusion and hold-up systems - Part 2-4 Intrusion detectors - Combined passive infrared microwave detectors《报警系统.入侵和拦截系统.第2-4部分 入侵检测.组合有源红外线 微波检测器》.pdf

《IEC 62642-2-4-2010 Alarm systems - Intrusion and hold-up systems - Part 2-4 Intrusion detectors - Combined passive infrared microwave detectors《报警系统.入侵和拦截系统.第2-4部分 入侵检测.组合有源红外线 微波检测器》.pdf》由会员分享，可在线阅读，更多相关《IEC 62642-2-4-2010 Alarm systems - Intrusion and hold-up systems - Part 2-4 Intrusion detectors - Combined passive infrared microwave detectors《报警系统.入侵和拦截系统.第2-4部分 入侵检测.组合有源红外线 微波检测器》.pdf（96页珍藏版）》请在麦多课文档分享上搜索。

1、 IEC 62642-2-4 Edition 1.0 2010-12 INTERNATIONAL STANDARD NORME INTERNATIONALE Alarm systems Intrusion and hold-up systems Part 2-4: Intrusion detectors Combined passive infrared / Microwave detectors Systmes dalarme Systmes dalarme contre lintrusion et les hold-up Partie 2-4: Dtecteurs dintrusion D

2、tecteurs combins infrarouges passifs et hyperfrquences IEC 62642-2-4:2010 THIS PUBLICATION IS COPYRIGHT PROTECTED Copyright 2010 IEC, Geneva, Switzerland All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic

3、 or mechanical, including photocopying and microfilm, without permission in writing from either IEC or IECs member National Committee in the country of the requester. If you have any questions about IEC copyright or have an enquiry about obtaining additional rights to this publication, please contac

4、t the address below or your local IEC member National Committee for further information. Droits de reproduction rservs. Sauf indication contraire, aucune partie de cette publication ne peut tre reproduite ni utilise sous quelque forme que ce soit et par aucun procd, lectronique ou mcanique, y compri

5、s la photocopie et les microfilms, sans laccord crit de la CEI ou du Comit national de la CEI du pays du demandeur. Si vous avez des questions sur le copyright de la CEI ou si vous dsirez obtenir des droits supplmentaires sur cette publication, utilisez les coordonnes ci-aprs ou contactez le Comit n

6、ational de la CEI de votre pays de rsidence. IEC Central Office 3, rue de Varemb CH-1211 Geneva 20 Switzerland Email: inmailiec.ch Web: www.iec.ch About the IEC The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes International Standards

7、for all electrical, electronic and related technologies. About IEC publications The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the latest edition, a corrigenda or an amendment might have been published. Catalogue of IEC publications

8、: www.iec.ch/searchpub The IEC on-line Catalogue enables you to search by a variety of criteria (reference number, text, technical committee,). It also gives information on projects, withdrawn and replaced publications. IEC Just Published: www.iec.ch/online_news/justpub Stay up to date on all new IE

9、C publications. Just Published details twice a month all new publications released. Available on-line and also by email. Electropedia: www.electropedia.org The worlds leading online dictionary of electronic and electrical terms containing more than 20 000 terms and definitions in English and French,

10、 with equivalent terms in additional languages. Also known as the International Electrotechnical Vocabulary online. Customer Service Centre: www.iec.ch/webstore/custserv If you wish to give us your feedback on this publication or need further assistance, please visit the Customer Service Centre FAQ

11、or contact us: Email: csciec.ch Tel.: +41 22 919 02 11 Fax: +41 22 919 03 00 A propos de la CEI La Commission Electrotechnique Internationale (CEI) est la premire organisation mondiale qui labore et publie des normes internationales pour tout ce qui a trait llectricit, llectronique et aux technologi

12、es apparentes. A propos des publications CEI Le contenu technique des publications de la CEI est constamment revu. Veuillez vous assurer que vous possdez ldition la plus rcente, un corrigendum ou amendement peut avoir t publi. Catalogue des publications de la CEI: www.iec.ch/searchpub/cur_fut-f.htm

13、Le Catalogue en-ligne de la CEI vous permet deffectuer des recherches en utilisant diffrents critres (numro de rfrence, texte, comit dtudes,). Il donne aussi des informations sur les projets et les publications retires ou remplaces. Just Published CEI: www.iec.ch/online_news/justpub Restez inform su

14、r les nouvelles publications de la CEI. Just Published dtaille deux fois par mois les nouvelles publications parues. Disponible en-ligne et aussi par email. Electropedia: www.electropedia.org Le premier dictionnaire en ligne au monde de termes lectroniques et lectriques. Il contient plus de 20 000 t

15、ermes et dfinitions en anglais et en franais, ainsi que les termes quivalents dans les langues additionnelles. Egalement appel Vocabulaire Electrotechnique International en ligne. Service Clients: www.iec.ch/webstore/custserv/custserv_entry-f.htm Si vous dsirez nous donner des commentaires sur cette

16、 publication ou si vous avez des questions, visitez le FAQ du Service clients ou contactez-nous: Email: csciec.ch Tl.: +41 22 919 02 11 Fax: +41 22 919 03 00 IEC 62642-2-4 Edition 1.0 2010-12 INTERNATIONAL STANDARD NORME INTERNATIONALE Alarm systems Intrusion and hold-up systems Part 2-4: Intrusion

17、detectors Combined passive infrared / Microwave detectors Systmes dalarme Systmes dalarme contre lintrusion et les hold-up Partie 2-4: Dtecteurs dintrusion Dtecteurs combins infrarouges passifs et hyperfrquences INTERNATIONAL ELECTROTECHNICAL COMMISSION COMMISSION ELECTROTECHNIQUE INTERNATIONALE X I

18、CS 13.320 PRICE CODE CODE PRIX ISBN 978-2-88912-303-2 Registered trademark of the International Electrotechnical Commission Marque dpose de la Commission Electrotechnique Internationale 2 62642-2-4 IEC:2010 CONTENTS FORE WORD 4 INTRODUCTION 6 1 Scop e 7 2 Normative references 7 3 Terms, definitions

19、and abbreviations. 8 3.1 Terms and definitions . 8 3.2 Abbreviations . 9 4 Functional requirements 9 4.1 Indication signals or messages 9 4.2 Detection 10 4.3 Operational requirements 12 4.4 Immunity of the individual technologies to incorrect operation . 12 4.5 Tamper security . 12 4.6 Electrical r

20、equirements . 14 4.7 Environmental classification and conditions 15 5 Marking, identification and documentation . 15 5.1 Marking and/or identification . 15 5.2 Documentation. 15 6 Testing 16 6.1 General test conditions . 16 6.2 Basic detection test 17 6.3 Walk testing 18 6.4 Switch-on delay, time in

21、terval between signals and indication of detection . 20 6.5 Self tests . 21 6.6 Immunity of individual technologies to incorrect operation 21 6.7 Tamper security . 23 6.8 Electrical tests . 25 6.9 Environmental classification and conditions 27 6.10 Marking, identification and documentation 28 Annex

22、A (normative) Dimensions and requirements of the standardised test magnets. 29 Annex B (normative) General testing matrix . 32 Annex C (normative) Walk test diagrams 34 Annex D (normative) Procedure for calculation of the average temperature difference between the standard target and the background

23、. 37 Annex E (informative) Basic detection target for the basic test of detection capability . 39 Annex F (informative) Equipment for walk test velocity control . 40 Annex G (informative) Immunity to visible and near infrared radiation Notes on calibration of the light source . 41 Annex H (informati

24、ve) Immunity to microwave signal interference by fluorescent lights . 42 Annex I (informative) Example list of small tools . 43 Annex J (informative) Test for resistance to re-orientation of adjustable mountings 44 Bibliography . 45 Figure A.1 Test magnet Magnet Type 1 . 30 Figure A.2 Test magnet Ma

25、gnet Type 2 . 31 62642-2-4 IEC:2010 3 Figure C.1 Detection across the boundary 34 Figure C.2 Detection within the boundary . 34 Figure C.3 High velocity and intermittent movement 35 Figure C.4 Close-in detection 35 Figure C.5 Significant range reduction . 36 Figure H.1 Immunity to fluorescent lamp i

26、nterference 42 Figure J.1 Re-orientation test 44 Table 1 Events to be processed by grade . 9 Table 2 Generation of signals or messages 10 Table 3 General walk test velocity and attitude requirements 11 Table 4 Tamper security requirements . 14 Table 5 Electrical requirements . 14 Table 6 Range of ma

27、terials for masking tests . 25 Table 7 Operational tests 28 Table 8 Endurance tests . 28 4 62642-2-4 IEC:2010 INTERNATIONAL ELECTROTECHNICAL COMMISSION _ ALARM SYSTEMS INTRUSION AND HOLD-UP SYSTEMS Part 2-4: Intrusion detectors Combined passive infrared / Microwave detectors FOREWORD 1) The Internat

28、ional Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international co-operation on all questions concerning standardization in the electrical and electron

29、ic fields. To this end and in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their preparation is entrusted to technical committees;

30、any IEC National Committee interested in the subject dealt with may participate in this preparatory work. International, governmental and non- governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for Stand

31、ardization (ISO) in accordance with conditions determined by agreement between the two organizations. 2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international consensus of opinion on the relevant subjects since each technical committee has re

32、presentation from all interested IEC National Committees. 3) IEC Publications have the form of recommendations for international use and are accepted by IEC National Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC Publications is accurate,

33、IEC cannot be held responsible for the way in which they are used or for any misinterpretation by any end user. 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications transparently to the maximum extent possible in their national and regional pub

34、lications. Any divergence between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter. 5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity assessment services and, in some ar

35、eas, access to IEC marks of conformity. IEC is not responsible for any services carried out by independent certification bodies. 6) All users should ensure that they have the latest edition of this publication. 7) No liability shall attach to IEC or its directors, employees, servants or agents inclu

36、ding individual experts and members of its technical committees and IEC National Committees for any personal injury, property damage or other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and expenses arising out of the publication, use of, or relia

37、nce upon, this IEC Publication or any other IEC Publications. 8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is indispensable for the correct application of this publication. 9) Attention is drawn to the possibility that some of the el

38、ements of this IEC Publication may be the subject of patent rights. IEC shall not be held responsible for identifying any or all such patent rights. International Standard IEC 62642-2-4 has been prepared by IEC technical committee 79: Alarm and electronic security systems. This standard is based on

39、EN 50131-2-4 (2008). The text of this standard is based on the following documents: FDIS Report on voting 79/323/FDIS 79/329/RVD Full information on the voting for the approval of this standard can be found in the report on voting indicated in the above table. This publication has been drafted in ac

40、cordance with the ISO/IEC Directives, Part 2. 62642-2-4 IEC:2010 5 A list of all parts of the IEC 62642 series can be found, under the general title Alarm systems Intrusion and hold-up systems, on the IEC website. The committee has decided that the contents of this publication will remain unchanged

41、until the stability result date indicated on the IEC web site under “http:/webstore.iec.ch“ in the data related to the specific publication. At this date, the publication will be reconfirmed, withdrawn, replaced by a revised edition, or amended. 6 62642-2-4 IEC:2010 INTRODUCTION This part 2-4 of the

42、 IEC 62642 series of standards gives requirements for passive infrared and microwave detectors used in intrusion and hold-up alarm systems. The other parts of this series of standards are as follows: Part 1 System requirements Part 2-2 Intrusion detectors Passive infrared detectors Part 2-3 Intrusio

43、n detectors Microwave detectors Part 2-4 Intrusion detectors Combined passive infrared / Microwave detectors Part 2-5 Intrusion detectors Combined passive infrared / Ultrasonic detectors Part 2-6 Intrusion detectors Opening contacts (magnetic) Part 2-71 Intrusion detectors Glass break detectors Acou

44、stic Part 2-72 Intrusion detectors Glass break detectors Passive Part 2-73 Intrusion detectors Glass break detectors Active Part 3 Control and indicating equipment Part 4 Warning devices Part 5-3 Requirements for interconnections equipment using radio frequency techniques Part 6 Power supplies Part

45、7 Application guidelines Part 8 Security fog devices/systems This standard deals with combined passive infrared and microwave detectors (to be referred to as the detector) used as part of intrusion alarm systems installed in buildings. It includes four security grades and four environmental classes.

46、 The purpose of the detector is to detect the broad spectrum infrared radiation emitted by an intruder, to emit microwave radiation and analyse signals that are returned and to provide the necessary range of signals or messages to be used by the rest of the intrusion alarm system. The number and sco

47、pe of these signals or messages will be more comprehensive for systems that are specified at the higher grades. This International Standard is only concerned with the requirements and tests for the detector. Other types of detector are covered by other documents identified as in IEC 62642-2 series.

48、If a combined detector can be operated in each technology individually, it also meets the grade-dependant requirements of the standards having relevance to those technologies. 62642-2-4 IEC:2010 7 ALARM SYSTEMS INTRUSION AND HOLD-UP SYSTEMS Part 2-4: Intrusion detectors Combined passive infrared / M

49、icrowave detectors 1 Scope This part of the IEC 62642 is for combined passive infrared and microwave detectors installed in buildings and provides for security Grades 1 to 4 (see IEC 62642-1), specific or non- specific wired or wire-free detectors, and uses environmental classes I to IV (see IEC 62599-1). This standard does