IEC 62423-2009 Type F and type B residual current operated circuit-breakers with and without integral overcurrent protection for household and similar uses《家用及类似用途用带和不带整体过电保护的F型和B型剩余电流驱动的断路器》.pdf

《IEC 62423-2009 Type F and type B residual current operated circuit-breakers with and without integral overcurrent protection for household and similar uses《家用及类似用途用带和不带整体过电保护的F型和B型剩余电流驱动的断路器》.pdf》由会员分享，可在线阅读，更多相关《IEC 62423-2009 Type F and type B residual current operated circuit-breakers with and without integral overcurrent protection for household and similar uses《家用及类似用途用带和不带整体过电保护的F型和B型剩余电流驱动的断路器》.pdf（78页珍藏版）》请在麦多课文档分享上搜索。

1、 IEC 62423Edition 2.0 2009-11INTERNATIONAL STANDARD NORME INTERNATIONALEType F and type B residual current operated circuit-breakers with and without integral overcurrent protection for household and similar uses Interrupteurs automatiques courant diffrentiel rsiduel de type B et de type F avec et s

2、ans protection contre les surintensits incorpore pour usages domestiques et analogues IEC62423:2009 THIS PUBLICATION IS COPYRIGHT PROTECTED Copyright 2009 IEC, Geneva, Switzerland All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form o

3、r by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either IEC or IECs member National Committee in the country of the requester. If you have any questions about IEC copyright or have an enquiry about obtaining additional rights to this

4、publication, please contact the address below or your local IEC member National Committee for further information. Droits de reproduction rservs. Sauf indication contraire, aucune partie de cette publication ne peut tre reproduite ni utilise sous quelque forme que ce soit et par aucun procd, lectron

5、ique ou mcanique, y compris la photocopie et les microfilms, sans laccord crit de la CEI ou du Comit national de la CEI du pays du demandeur. Si vous avez des questions sur le copyright de la CEI ou si vous dsirez obtenir des droits supplmentaires sur cette publication, utilisez les coordonnes ci-ap

6、rs ou contactez le Comit national de la CEI de votre pays de rsidence. IEC Central Office 3, rue de Varemb CH-1211 Geneva 20 Switzerland Email: inmailiec.ch Web: www.iec.ch About the IEC The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishe

7、s International Standards for all electrical, electronic and related technologies. About IEC publications The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the latest edition, a corrigenda or an amendment might have been published. Cat

8、alogue of IEC publications: www.iec.ch/searchpub The IEC on-line Catalogue enables you to search by a variety of criteria (reference number, text, technical committee,). It also gives information on projects, withdrawn and replaced publications. IEC Just Published: www.iec.ch/online_news/justpub Sta

9、y up to date on all new IEC publications. Just Published details twice a month all new publications released. Available on-line and also by email. Electropedia: www.electropedia.org The worlds leading online dictionary of electronic and electrical terms containing more than 20 000 terms and definiti

10、ons in English and French, with equivalent terms in additional languages. Also known as the International Electrotechnical Vocabulary online. Customer Service Centre: www.iec.ch/webstore/custserv If you wish to give us your feedback on this publication or need further assistance, please visit the Cu

11、stomer Service Centre FAQ or contact us: Email: csciec.ch Tel.: +41 22 919 02 11 Fax: +41 22 919 03 00 A propos de la CEI La Commission Electrotechnique Internationale (CEI) est la premire organisation mondiale qui labore et publie des normes internationales pour tout ce qui a trait llectricit, llec

12、tronique et aux technologies apparentes. A propos des publications CEI Le contenu technique des publications de la CEI est constamment revu. Veuillez vous assurer que vous possdez ldition la plus rcente, un corrigendum ou amendement peut avoir t publi. Catalogue des publications de la CEI: www.iec.c

13、h/searchpub/cur_fut-f.htm Le Catalogue en-ligne de la CEI vous permet deffectuer des recherches en utilisant diffrents critres (numro de rfrence, texte, comit dtudes,). Il donne aussi des informations sur les projets et les publications retires ou remplaces. Just Published CEI: www.iec.ch/online_new

14、s/justpub Restez inform sur les nouvelles publications de la CEI. Just Published dtaille deux fois par mois les nouvelles publications parues. Disponible en-ligne et aussi par email. Electropedia: www.electropedia.org Le premier dictionnaire en ligne au monde de termes lectroniques et lectriques. Il

15、 contient plus de 20 000 termes et dfinitions en anglais et en franais, ainsi que les termes quivalents dans les langues additionnelles. Egalement appel Vocabulaire Electrotechnique International en ligne. Service Clients: www.iec.ch/webstore/custserv/custserv_entry-f.htm Si vous dsirez nous donner

16、des commentaires sur cette publication ou si vous avez des questions, visitez le FAQ du Service clients ou contactez-nous: Email: csciec.ch Tl.: +41 22 919 02 11 Fax: +41 22 919 03 00 IEC 62423Edition 2.0 2009-11INTERNATIONAL STANDARD NORME INTERNATIONALEType F and type B residual current operated c

17、ircuit-breakers with and without integral overcurrent protection for household and similar uses Interrupteurs automatiques courant diffrentiel rsiduel de type B et de type F avec et sans protection contre les surintensits incorpore pour usages domestiques et analogues INTERNATIONAL ELECTROTECHNICAL

18、COMMISSION COMMISSION ELECTROTECHNIQUE INTERNATIONALE WICS 29.120; 29.120.50 PRICE CODECODE PRIXISBN 2-8318-1070-3 Registered trademark of the International Electrotechnical Commission Marque dpose de la Commission Electrotechnique Internationale 2 62423 IEC:2009 CONTENTS FOREWORD.5 INTRODUCTION.7 1

19、 Scope.8 2 Normative references .8 3 Terms and definitions .9 4 Classification9 4.1 According to behaviour in presence of d.c. components 9 5 Characteristics .10 5.1 Type F residual current device 10 5.2 Type B residual current device 10 5.2.1 General .10 5.2.2 Standard values of break time and non-

20、actuating time for residual direct currents which result from rectifying circuits and for residual smooth direct current.10 5.2.3 Values of tripping current according to frequencies which differ from the rated frequency 50/60 Hz.11 6 Marking and other product information11 6.1 Marking for Type F RCD

21、s 11 6.2 Marking for Type B RCDs11 7 Standard conditions for operation in service and for installation11 8 Conditions for construction and operation.12 8.1 Conditions for Type F and Type B RCDs Requirements for operation in case of sinusoidal residual currents comprising of multi-frequency component

22、s resulting from control equipment supplied from single phase .12 8.2 Conditions for Type B RCDs12 8.2.1 Operation in response to the type of residual current.12 8.3 Behaviour of Type F and Type B RCDs .13 8.3.1 Behaviour of RCDs in the case of surge residual currents .13 8.3.2 Behaviour of RCDs in

23、the case of inrush residual currents.14 8.3.3 Behaviour in case of residual pulsating direct currents in presence of a standing smooth direct current of 0,01 A.14 9 Tests 14 9.1 Tests for Type F and Type B RCDs .14 9.1.1 General .14 9.1.2 Verification of the correct operation in case of a steady inc

24、rease of composite residual current.14 9.1.3 Verification of the correct operation in case of sudden appearance of composite residual current.15 9.1.4 Verification of the correct operation for four-pole Type F RCD powered on two poles only 15 9.1.5 Verification of behaviour at surge currents up to 3

25、 000 A (8/20 s surge current test) .15 9.1.6 Verification of behaviour in the case of inrush residual currents.16 9.1.7 Verification of the correct operation in case of residual pulsating direct currents in presence of a standing smooth direct current of 0,01 A .16 9.2 Tests for Type B RCDs16 62423

26、IEC:2009 3 9.2.1 Verification of the operating characteristic at the reference temperature (20 5) C16 9.2.2 Tests at the temperature limits 19 9.2.3 Verification of the correct operation for three- and four-pole Type B RCDs powered on two poles only 19 9.2.4 Verification of the RCD after test sequen

27、ces19 Annex A (normative) Number of samples to be submitted and test sequences to be applied for verification of conformity for type F RCCBs .28 Annex B (normative) Number of samples to be submitted and test sequences to be applied for verification of conformity for Type F RCBOs 30 Annex C (normativ

28、e) Number of samples to be submitted and test sequences to be applied for verification of conformity for Type B RCCBs 32 Annex D (normative) Number of samples to be submitted and test sequences to be applied for verification of conformity for Type B RCBOs 34 Annex E (normative) Routine tests for Typ

29、e F and Type B RCDs .36 Bibliography37 Figure 1 Example of a test circuit for the verification of correct operation in case of residual sinusoidal alternating currents composed of multi-frequency components resulting from single-phase supplied speed motor control equipment 20 Figure 2 Test circuit f

30、or the verification of the behaviour of the RCD in case of inrush residual currents.21 Figure 3 Test circuit for the verification of correct operation in case of residual sinusoidal alternating current up to 1 000 Hz 22 Figure 4 Test circuit for 2-, 3- and 4-pole Type B RCD to verify the correct ope

31、ration in case of a residual alternating current superimposed on a smooth direct current .23 Figure 5 Test circuit for 2-, 3- and 4-pole Type B RCD to verify the correct operation in case of a residual pulsating direct current superimposed on a smooth direct current24 Figure 6a Test circuit for 2-,

32、3- and 4-pole Type B to verify the correct operation in case of residual pulsating direct currents which may result from rectifying circuits supplied from two phases .25 Figure 6b Test circuit for 3- and 4-pole Type B RCD to verify the correct operation in case of residual pulsating direct currents

33、which may result from rectifying circuits supplied from three phases.26 Figure 6 Test circuit for Type B RCD to verify the correct operation in case of residual pulsating direct currents which may result from rectifying circuits .26 Figure 7 Test circuit for 2-, 3- and 4-pole Type B RCD to verify th

34、e correct operation in case of a residual smooth direct current27 Table 1 Type B RCDs Standard values of break time and non-actuating time for residual direct currents which result from rectifying circuits and for residual smooth direct current 10 Table 2 Type B RCDs Residual non-operating and opera

35、ting current according to frequencies which differ from the rated frequency 50/60 Hz 11 Table 3 Different frequency component values of test currents and starting current values (I) for verifying the operating in case of steady increased residual current14 Table 4 Operating current ranges for compos

36、ite residual current .15 Table A.1 Test sequences for Type F RCCBs 29 Table B.1 Test sequences for Type F RCBOs 31 Table C.1 Test sequences for Type B RCCBs 32 4 62423 IEC:2009 Table D.1 Test sequences for Type B RCBOs34 62423 IEC:2009 5 INTERNATIONAL ELECTROTECHNICAL COMMISSION _ TYPE F AND TYPE B

37、RESIDUAL CURRENT OPERATED CIRCUIT-BREAKERS WITH AND WITHOUT INTEGRAL OVERCURRENT PROTECTION FOR HOUSEHOLD AND SIMILAR USES FOREWORD 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising all national electrotechnical committees (IEC National

38、 Committees). The object of IEC is to promote international co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports, Publicly

39、Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with may participate in this preparatory work. International, governmental and non-governmenta

40、l organizations liaising with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for Standardization (ISO) in accordance with conditions determined by agreement between the two organizations. 2) The formal decisions or agreements of IEC on tech

41、nical matters express, as nearly as possible, an international consensus of opinion on the relevant subjects since each technical committee has representation from all interested IEC National Committees. 3) IEC Publications have the form of recommendations for international use and are accepted by I

42、EC National Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any misinterpretation by any end user. 4) In order to promote international unifo

43、rmity, IEC National Committees undertake to apply IEC Publications transparently to the maximum extent possible in their national and regional publications. Any divergence between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter. 5)

44、IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any services carried out by independent certification bodies. 6) All users should ensur

45、e that they have the latest edition of this publication. 7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and members of its technical committees and IEC National Committees for any personal injury, property damage or other damage of an

46、y nature whatsoever, whether direct or indirect, or for costs (including legal fees) and expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC Publications. 8) Attention is drawn to the Normative references cited in this publication. Use of the refe

47、renced publications is indispensable for the correct application of this publication. 9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent rights. IEC shall not be held responsible for identifying any or all such patent rights. Inter

48、national Standard IEC 62423 has been prepared by subcommittee 23E: Circuit-breakers and similar equipment for household use, of IEC technical committee 23: Electrical accessories. This second edition cancels and replaces the first edition published in 2007 and constitutes a technical revision. The m

49、ain changes from the first edition are as follows: requirements and tests for Type F RCD have been introduced; requirements and tests for two-pole Type B RCD have been introduced; new additional requirements and tests for Type B RCDs have been introduced to cover requirements and tests for Type F too. 6 62423 IEC:2009 The text of this standard is based on the following documents: FDIS Report on v