IEC 61754-29-2012 Fibre optic interconnecting devices and passive components - Fibre optic connector interfaces - Part 29 Type BLINK connector series《光纤互连设备和无源元件.光纤连接器接口.第29部分 BLINK型连接器系列》.pdf

《IEC 61754-29-2012 Fibre optic interconnecting devices and passive components - Fibre optic connector interfaces - Part 29 Type BLINK connector series《光纤互连设备和无源元件.光纤连接器接口.第29部分 BLINK型连接器系列》.pdf》由会员分享，可在线阅读，更多相关《IEC 61754-29-2012 Fibre optic interconnecting devices and passive components - Fibre optic connector interfaces - Part 29 Type BLINK connector series《光纤互连设备和无源元件.光纤连接器接口.第29部分 BLINK型连接器系列》.pdf（52页珍藏版）》请在麦多课文档分享上搜索。

1、 IEC 61754-29 Edition 1.0 2012-04 INTERNATIONAL STANDARD NORME INTERNATIONALE Fibre optic interconnecting devices and passive components Fibre optic connector interfaces Part 29: Type BLINK connector series Dispositifs dinterconnexion et composants passifs fibres optiques Interfaces de connecteurs p

2、our fibres optiques Partie 29: Srie de connecteurs de type BLINK IEC 61754-29:2012 THIS PUBLICATION IS COPYRIGHT PROTECTED Copyright 2012 IEC, Geneva, Switzerland All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, e

3、lectronic or mechanical, including photocopying and microfilm, without permission in writing from either IEC or IECs member National Committee in the country of the requester. If you have any questions about IEC copyright or have an enquiry about obtaining additional rights to this publication, plea

4、se contact the address below or your local IEC member National Committee for further information. Droits de reproduction rservs. Sauf indication contraire, aucune partie de cette publication ne peut tre reproduite ni utilise sous quelque forme que ce soit et par aucun procd, lectronique ou mcanique,

5、 y compris la photocopie et les microfilms, sans laccord crit de la CEI ou du Comit national de la CEI du pays du demandeur. Si vous avez des questions sur le copyright de la CEI ou si vous dsirez obtenir des droits supplmentaires sur cette publication, utilisez les coordonnes ci-aprs ou contactez l

6、e Comit national de la CEI de votre pays de rsidence. IEC Central Office Tel.: +41 22 919 02 11 3, rue de Varemb Fax: +41 22 919 03 00 CH-1211 Geneva 20 infoiec.ch Switzerland www.iec.ch About the IEC The International Electrotechnical Commission (IEC) is the leading global organization that prepare

7、s and publishes International Standards for all electrical, electronic and related technologies. About IEC publications The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the latest edition, a corrigenda or an amendment might have been

8、published. Useful links: IEC publications search - www.iec.ch/searchpub The advanced search enables you to find IEC publications by a variety of criteria (reference number, text, technical committee,). It also gives information on projects, replaced and withdrawn publications. IEC Just Published - w

9、ebstore.iec.ch/justpublished Stay up to date on all new IEC publications. Just Published details all new publications released. Available on-line and also once a month by email. Electropedia - www.electropedia.org The worlds leading online dictionary of electronic and electrical terms containing mor

10、e than 30 000 terms and definitions in English and French, with equivalent terms in additional languages. Also known as the International Electrotechnical Vocabulary (IEV) on-line. Customer Service Centre - webstore.iec.ch/csc If you wish to give us your feedback on this publication or need further

11、assistance, please contact the Customer Service Centre: csciec.ch. A propos de la CEI La Commission Electrotechnique Internationale (CEI) est la premire organisation mondiale qui labore et publie des Normes internationales pour tout ce qui a trait llectricit, llectronique et aux technologies apparen

12、tes. A propos des publications CEI Le contenu technique des publications de la CEI est constamment revu. Veuillez vous assurer que vous possdez ldition la plus rcente, un corrigendum ou amendement peut avoir t publi. Liens utiles: Recherche de publications CEI - www.iec.ch/searchpub La recherche ava

13、nce vous permet de trouver des publications CEI en utilisant diffrents critres (numro de rfrence, texte, comit dtudes,). Elle donne aussi des informations sur les projets et les publications remplaces ou retires. Just Published CEI - webstore.iec.ch/justpublished Restez inform sur les nouvelles publ

14、ications de la CEI. Just Published dtaille les nouvelles publications parues. Disponible en ligne et aussi une fois par mois par email. Electropedia - www.electropedia.org Le premier dictionnaire en ligne au monde de termes lectroniques et lectriques. Il contient plus de 30 000 termes et dfinitions

15、en anglais et en franais, ainsi que les termes quivalents dans les langues additionnelles. Egalement appel Vocabulaire Electrotechnique International (VEI) en ligne. Service Clients - webstore.iec.ch/csc Si vous dsirez nous donner des commentaires sur cette publication ou si vous avez des questions

16、contactez-nous: csciec.ch. IEC 61754-29 Edition 1.0 2012-04 INTERNATIONAL STANDARD NORME INTERNATIONALE Fibre optic interconnecting devices and passive components Fibre optic connector interfaces Part 29: Type BLINK connector series Dispositifs dinterconnexion et composants passifs fibres optiques I

17、nterfaces de connecteurs pour fibres optiques Partie 29: Srie de connecteurs de type BLINK INTERNATIONAL ELECTROTECHNICAL COMMISSION COMMISSION ELECTROTECHNIQUE INTERNATIONALE T ICS 33.180.20 PRICE CODE CODE PRIX ISBN 978-2-88912-039-0 Registered trademark of the International Electrotechnical Commi

18、ssion Marque dpose de la Commission Electrotechnique Internationale Warning! Make sure that you obtained this publication from an authorized distributor. Attention! Veuillez vous assurer que vous avez obtenu cette publication via un distributeur agr. 2 61754-29 IEC:2012 CONTENTS FOREWORD . 3 INTRODU

19、CTION . 5 1 Scope . 6 2 Normative references . 6 3 Description . 6 4 Interfaces . 6 5 Plug optical interface 7 6 Plug 9 7 Simplex adaptor . 16 8 Duplex adaptor . 21 9 Pin gauge for adaptor . 24 Figure 1 Plug connector interface reference planes . 7 Figure 2 Detail A of figure 1 APC/PC endface geomet

20、ry, expanded view drawings not-to-scale. 8 Figure 3 Top view (APC) 8 Figure 4 Plug connector interface 12 Figure 5 APC simplex plug connector interface 13 Figure 6 Duplex plug interface . 13 Figure 7 Simplex adaptor (isometric view) 16 Figure 8 Simplex adaptor . 17 Figure 9 Simplex adaptor interface

21、. 19 Figure 10 Simplex adaptor interface section A A 20 Figure 11 Duplex adaptor (isometric view) . 21 Figure 12 Duplex adaptor . 21 Figure 13 Duplex adaptor . 22 Figure 14 Duplex adaptor with dimensions . 22 Figure 15 Pin gauge for adaptor . 24 Table 1 Intermateability between plugs and adaptors wi

22、thin the IEC 61754-29 series 7 Table 2 Intermateability between plugs within the IEC 61754-29 series 7 Table 3 Dimensions of the plug connector interface . 14 Table 4 Plug connector interface Ferrule grade . 15 Table 5 Dimensions of the BLINK BLINK adaptor interface . 23 Table 6 Pin gauge dimensions

23、 24 61754-29 IEC:2012 3 INTERNATIONAL ELECTROTECHNICAL COMMISSION _ FIBRE OPTIC INTERCONNECTING DEVICES AND PASSIVE COMPONENTS FIBRE OPTIC CONNECTOR INTERFACES Part 29: Type BLINK connector series FOREWORD 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standar

24、dization comprising all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and in addition to other activities, IEC publishes Inter

25、national Standards, Technical Specifications, Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with may participate

26、 in this preparatory work. International, governmental and non- governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for Standardization (ISO) in accordance with conditions determined by agreement between

27、the two organizations. 2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international consensus of opinion on the relevant subjects since each technical committee has representation from all interested IEC National Committees. 3) IEC Publications h

28、ave the form of recommendations for international use and are accepted by IEC National Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any mi

29、sinterpretation by any end user. 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications transparently to the maximum extent possible in their national and regional publications. Any divergence between any IEC Publication and the corresponding nat

30、ional or regional publication shall be clearly indicated in the latter. 5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any services

31、 carried out by independent certification bodies. 6) All users should ensure that they have the latest edition of this publication. 7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and members of its technical committees and IEC Nationa

32、l Committees for any personal injury, property damage or other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC Publications. 8) Attention is d

33、rawn to the Normative references cited in this publication. Use of the referenced publications is indispensable for the correct application of this publication. International Standard IEC 61754-29 has been prepared by subcommittee 86B: Fibre optic interconnecting devices and passive components, of I

34、EC technical committee 86: Fibre optics. The text of this standard is based on the following documents: FDIS Report on voting 86B/3369/FDIS 86B/3416/RVD Full information on the voting for the approval of this standard can be found in the report on voting indicated in the above table. This publicatio

35、n has been drafted in accordance with the ISO/IEC Directives, Part 2. 4 61754-29 IEC:2012 The committee has decided that the contents of this publication will remain unchanged until the stability date indicated on the IEC web site under “http:/webstore.iec.ch“ in the data related to the specific pub

36、lication. At this date, the publication will be reconfirmed, withdrawn, replaced by a revised edition, or amended. 61754-29 IEC:2012 5 INTRODUCTION The International Electrotechnical Commission (IEC) draws attention to the fact that it is claimed that compliance with this document may involve the us

37、e of a patent concerning IEC 61754-29. IEC takes no position concerning the evidence, validity and scope of this patent right. The holder of this patent right has assured the IEC that he/she is willing to negotiate licences under reasonable and non-discriminatory terms and conditions with applicants

38、 throughout the world. In this respect, the statement of the holder of this patent right is registered with IEC. Information may be obtained from: Huber+Suhner AG Degersheimerstrasse 14 9100 Herisau Switzerland Attention is drawn to the possibility that some of the elements of this document may be t

39、he subject of patent rights other than those identified above. IEC shall not be held responsible for identifying any or all such patent rights. ISO (www.iso.org/patents) and IEC (http:/www.iec.ch/tctools/patent_decl.htm) maintain on- line data bases of patents relevant to their standards. Users are

40、encouraged to consult the data bases for the most up to date information concerning patents. 6 61754-29 IEC:2012 FIBRE OPTIC INTERCONNECTING DEVICES AND PASSIVE COMPONENTS FIBRE OPTIC CONNECTOR INTERFACES Part 29: Type BLINK connector series 1 Scope This part of IEC 61754 defines the standard interf

41、ace dimensions for the type BLINK series of connectors. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest

42、 edition of the referenced document (including any amendments) applies. IEC 60794-2-50, Optical fibre cables Part 2-50: Indoor cables Family specification for simplex and duplex cables for use in terminated cable assemblies IEC 61754-1, Fibre optic interconnecting devices and passive components Fibr

43、e optic connector interfaces Part 1: General and guidance IEC 61755-3 (all parts), Fibre optic interconnecting devices and passive components Fibre optic connector optical interfaces 3 Description The parent connector for the type BLINK connector family is a single position plug connector set of plu

44、g/adaptor/plug configuration which is characterized by a 1,25 mm nominal diameter ferrule. The connector includes a ferrule spring loaded in the direction of the optical axis. The optical alignment mechanism of the connection is of a resilient sleeve style. 4 Interfaces The general requirements defi

45、ned in IEC 61754-1 are valid for this standard. Clauses 4 to 8 define the standard interfaces for the type BLINK connector series. The standard interfaces contained in this document are listed in the following: INTERFACE 29-1: Simplex Plug Connector Interface PC INTERFACE 29-2: Simplex Adaptor Inter

46、face INTERFACE 29-3: Duplex Plug Connector Interface PC INTERFACE 29-4: Duplex Adaptor Interface INTERFACE 29-5: Simplex Plug Connector Interface APC 8 INTERFACE 29-6: Duplex Plug Connector Interface APC 8 The following plugs and adaptors shown in Table 1 and Table 2 are intermateable. 61754-29 IEC:

47、2012 7 Table 1 Intermateability between plugs and adaptors within the IEC 61754-29 series Plugs (polishing condition) Adaptor Interfaces 61754-29-2 61754-29-4 Interface 61754-29-1 mate mate Interface 61754-29-3 Not mate mate Interface 61754-29-5 mate mate Interface 61754-29-6 Not mate mate Table 2 I

48、ntermateability between plugs within the IEC 61754-29 series Plugs (polishing condition) Plugs (polishing condition) 61754-29-1 61754-29-3 61754-29-5 61754-29-6 61754-29-1 mate mate Not mate Not mate 61754-29-3 mate mate Not mate Not mate 61754-29-5 Not mate Not mate mate mate 61754-29-6 Not mate No

49、t mate mate mate 5 Plug optical interface Plug optical interfaces are sown in Figure 1, Figure 2 and Figure 3. Detail A Optical datum target Optical reference plane Mechanical reference plane IEC 527/12 NOTE Shown without shutter to make features more visible (see Figure 4c) for shutter details). Figure 1 Plug connector interface reference planes The plug o