IEC 61439-5-2014 Low-voltage switchgear and controlgear assemblies - Part 5 Assemblies for power distribution in public networks《低压开关设备和控制设备配件.第5部分 公共网络配电用配件》.pdf

《IEC 61439-5-2014 Low-voltage switchgear and controlgear assemblies - Part 5 Assemblies for power distribution in public networks《低压开关设备和控制设备配件.第5部分 公共网络配电用配件》.pdf》由会员分享，可在线阅读，更多相关《IEC 61439-5-2014 Low-voltage switchgear and controlgear assemblies - Part 5 Assemblies for power distribution in public networks《低压开关设备和控制设备配件.第5部分 公共网络配电用配件》.pdf（76页珍藏版）》请在麦多课文档分享上搜索。

1、 IEC 61439-5 Edition 2.0 2014-08 INTERNATIONAL STANDARD NORME INTERNATIONALE Low-voltage switchgear and controlgear assemblies Part 5: Assemblies for power distribution in public networks Ensembles dappareillage basse tension Partie 5: Ensembles pour rseaux de distribution publique IEC 61439-5:2014-

2、08(en-fr) THIS PUBLICATION IS COPYRIGHT PROTECTED Copyright 2014 IEC, Geneva, Switzerland All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without pe

3、rmission in writing from either IEC or IECs member National Committee in the country of the requester. If you have any questions about IEC copyright or have an enquiry about obtaining additional rights to this publication, please contact the address below or your local IEC member National Committee

4、for further information. Droits de reproduction rservs. Sauf indication contraire, aucune partie de cette publication ne peut tre reproduite ni utilise sous quelque forme que ce soit et par aucun procd, lectronique ou mcanique, y compris la photocopie et les microfilms, sans laccord crit de lIEC ou

5、du Comit national de lIEC du pays du demandeur. Si vous avez des questions sur le copyright de lIEC ou si vous dsirez obtenir des droits supplmentaires sur cette publication, utilisez les coordonnes ci-aprs ou contactez le Comit national de lIEC de votre pays de rsidence. IEC Central Office Tel.: +4

6、1 22 919 02 11 3, rue de Varemb Fax: +41 22 919 03 00 CH-1211 Geneva 20 infoiec.ch Switzerland www.iec.ch About the IEC The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes International Standards for all electrical, electronic and relate

7、d technologies. About IEC publications The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the latest edition, a corrigenda or an amendment might have been published. IEC Catalogue - webstore.iec.ch/catalogue The stand-alone application

8、for consulting the entire bibliographical information on IEC International Standards, Technical Specifications, Technical Reports and other documents. Available for PC, Mac OS, Android Tablets and iPad. IEC publications search - www.iec.ch/searchpub The advanced search enables to find IEC publicatio

9、ns by a variety of criteria (reference number, text, technical committee,). It also gives information on projects, replaced and withdrawn publications. IEC Just Published - webstore.iec.ch/justpublished Stay up to date on all new IEC publications. Just Published details all new publications released

10、. Available online and also once a month by email. Electropedia - www.electropedia.org The worlds leading online dictionary of electronic and electrical terms containing more than 30 000 terms and definitions in English and French, with equivalent terms in 14 additional languages. Also known as the

11、International Electrotechnical Vocabulary (IEV) online. IEC Glossary - std.iec.ch/glossary More than 55 000 electrotechnical terminology entries in English and French extracted from the Terms and Definitions clause of IEC publications issued since 2002. Some entries have been collected from earlier

12、publications of IEC TC 37, 77, 86 and CISPR. IEC Customer Service Centre - webstore.iec.ch/csc If you wish to give us your feedback on this publication or need further assistance, please contact the Customer Service Centre: csciec.ch. A propos de lIEC La Commission Electrotechnique Internationale (I

13、EC) est la premire organisation mondiale qui labore et publie des Normes internationales pour tout ce qui a trait llectricit, llectronique et aux technologies apparentes. A propos des publications IEC Le contenu technique des publications IEC est constamment revu. Veuillez vous assurer que vous poss

14、dez ldition la plus rcente, un corrigendum ou amendement peut avoir t publi. Catalogue IEC - webstore.iec.ch/catalogue Application autonome pour consulter tous les renseignements bibliographiques sur les Normes internationales, Spcifications techniques, Rapports techniques et autres documents de lIE

15、C. Disponible pour PC, Mac OS, tablettes Android et iPad. Recherche de publications IEC - www.iec.ch/searchpub La recherche avance permet de trouver des publications IEC en utilisant diffrents critres (numro de rfrence, texte, comit dtudes,). Elle donne aussi des informations sur les projets et les

16、publications remplaces ou retires. IEC Just Published - webstore.iec.ch/justpublished Restez inform sur les nouvelles publications IEC. Just Published dtaille les nouvelles publications parues. Disponible en ligne et aussi une fois par mois par email. Electropedia - www.electropedia.org Le premier d

17、ictionnaire en ligne de termes lectroniques et lectriques. Il contient plus de 30 000 termes et dfinitions en anglais et en franais, ainsi que les termes quivalents dans 14 langues additionnelles. Egalement appel Vocabulaire Electrotechnique International (IEV) en ligne. Glossaire IEC - std.iec.ch/g

18、lossary Plus de 55 000 entres terminologiques lectrotechniques, en anglais et en franais, extraites des articles Termes et Dfinitions des publications IEC parues depuis 2002. Plus certaines entres antrieures extraites des publications des CE 37, 77, 86 et CISPR de lIEC. Service Clients - webstore.ie

19、c.ch/csc Si vous dsirez nous donner des commentaires sur cette publication ou si vous avez des questions contactez-nous: csciec.ch. IEC 61439-5 Edition 2.0 2014-08 INTERNATIONAL STANDARD NORME INTERNATIONALE Low-voltage switchgear and controlgear assemblies Part 5: Assemblies for power distribution

20、in public networks Ensembles dappareillage basse tension Partie 5: Ensembles pour rseaux de distribution publique INTERNATIONAL ELECTROTECHNICAL COMMISSION COMMISSION ELECTROTECHNIQUE INTERNATIONALE W ICS 29.130.20 PRICE CODE CODE PRIX ISBN 978-2-8322-1831-0 Registered trademark of the International

21、 Electrotechnical Commission Marque dpose de la Commission Electrotechnique Internationale Warning! Make sure that you obtained this publication from an authorized distributor. Attention! Veuillez vous assurer que vous avez obtenu cette publication via un distributeur agr. 2 IEC 61439-5:2014 IEC 201

22、4 CONTENTS FOREWORD . 3 1 Scope 5 2 Normative references. 6 3 Terms and definitions 6 4 Symbols and abbreviations 7 5 Interface characteristics . 7 6 Information 8 7 Service conditions . 8 8 Constructional requirements 9 9 Performance requirements . 11 10 Design verification . 11 11 Routine verifica

23、tion 24 Annexes . 25 Annex O (informative) Guidance on temperature rise verification 26 Annex AA (normative) Cross-section of conductors . 27 Annex BB (informative) Items subject to agreement between the ASSEMBLY manufacturer and the user . 29 Annex CC (informative) Design verification . 33 Annex DD

24、 (informative) List of notes concerning certain countries 34 Bibliography . 35 Figure 101 Typical distribution network . 6 Figure 102 Diagram of test to verify resistance to shock load of a PENDA-O . 14 Figure 103 Diagram of test to verify impact force withstand of a PENDA-O 15 Figure 104 Diagram of

25、 test to verify the resistance to static load . 16 Figure 105 Sandbag for test to verify the resistance to shock load 17 Figure 106 Diagram of test to verify resistance to torsional stress of a PENDA-O 18 Figure 107 Diagram of test to verify the mechanical strength of doors . 21 Figure 108 Striker e

26、lement for test of resistance to mechanical shock impacts induced by sharp-edged objects 22 Figure 109 Typical test arrangement for mechanical strength of base 23 Table 101 Values of assumed loading 8 Table 102 Axial load to be applied to the inserts . 22 Table AA.1 Minimum and maximum cross-section

27、 of copper and aluminium conductors, suitable for connection (see 8.8) . 27 Table AA.2 Standard cross-sections of round copper conductors and approximate relationship between mm 2and AWG/kcmil sizes (see 8.8 of Part 1) . 28 Table BB.1 Items subject to agreement between the ASSEMBLY manufacturer and

28、the user 29 Table CC.1 List of design verifications to be performed . 33 IEC 61439-5:2014 IEC 2014 3 INTERNATIONAL ELECTROTECHNICAL COMMISSION _ LOW-VOLTAGE SWITCHGEAR AND CONTROLGEAR ASSEMBLIES Part 5: Assemblies for power distribution in public networks FOREWORD 1) The International Electrotechnic

29、al Commission (IEC) is a worldwide organization for standardization comprising all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international co-operation on all questions concerning standardization in the electrical and electronic fields. To this e

30、nd and in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Com

31、mittee interested in the subject dealt with may participate in this preparatory work. International, governmental and non- governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for Standardization (ISO) in

32、accordance with conditions determined by agreement between the two organizations. 2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international consensus of opinion on the relevant subjects since each technical committee has representation from al

33、l interested IEC National Committees. 3) IEC Publications have the form of recommendations for international use and are accepted by IEC National Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC Publications is accurate, IEC cannot be held r

34、esponsible for the way in which they are used or for any misinterpretation by any end user. 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications transparently to the maximum extent possible in their national and regional publications. Any diver

35、gence between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter. 5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity assessment services and, in some areas, access to IEC m

36、arks of conformity. IEC is not responsible for any services carried out by independent certification bodies. 6) All users should ensure that they have the latest edition of this publication. 7) No liability shall attach to IEC or its directors, employees, servants or agents including individual expe

37、rts and members of its technical committees and IEC National Committees for any personal injury, property damage or other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and expenses arising out of the publication, use of, or reliance upon, this IEC P

38、ublication or any other IEC Publications. 8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is indispensable for the correct application of this publication. 9) Attention is drawn to the possibility that some of the elements of this IEC P

39、ublication may be the subject of patent rights. IEC shall not be held responsible for identifying any or all such patent rights. International Standard IEC 61439-5 has been prepared by subcommittee 17D: Low-voltage switchgear and controlgear assemblies, of IEC technical committee 17: Switchgear and

40、controlgear. This second edition cancels and replaces the first edition published in 2010. It constitutes a technical revision. This edition includes the following significant technical changes with respect to the latest edition: confirmation that tests carried out on the most onerous PENDA are deem

41、ed to verify the performance of similar and less onerous assemblies of the same general construction and rating; more precise timing/conditions for impact force withstand tests for PENDAs designed for operation in an arctic climate; correction of the direction of the applied force in the static load

42、 test. 4 IEC 61439-5:2014 IEC 2014 The text of this standard is based on the following documents: CDV Report on voting 17D/492/CDV 121B/13/RVC Full information on the voting for the approval of this standard can be found in the report on voting indicated in the above table. This publication has been

43、 drafted in accordance with the ISO/IEC Directives, Part 2. This standard is to be read in conjunction with IEC 61439-1. The provisions of the general rules dealt with in IEC 61439-1 (hereinafter referred to as Part 1) are only applicable to this standard insofar as they are specifically cited. When

44、 this standard states “addition”, “modification” or “replacement”, the relevant text in Part 1 is to be adapted accordingly. Subclauses that are numbered with a 101 (102, 103 etc.) suffix are additional to the same subclause in Part 1. Tables and figures in this Part 5 that are new are numbered star

45、ting with 101. New annexes in this Part 5 are lettered AA, BB, etc. In this standard, terms written in small capitals are defined in Clause 3. The readers attention is drawn to the fact that Annex DD lists all of the “in-some-country” clauses on differing practices of a less permanent nature relatin

46、g to the subject of this standard. A list of all parts of the IEC 61439 series, under the general title Low-voltage switchgear and controlgear assemblies can be found on the IEC website. The committee has decided that the contents of this publication will remain unchanged until the stability date in

47、dicated on the IEC web site under “http:/webstore.iec.ch“ in the data related to the specific publication. At this date, the publication will be reconfirmed, withdrawn, replaced by a revised edition, or amended. IEC 61439-5:2014 IEC 2014 5 LOW-VOLTAGE SWITCHGEAR AND CONTROLGEAR ASSEMBLIES Part 5: As

48、semblies for power distribution in public networks 1 Scope This part of IEC 61439 defines the specific requirements for public electricity network distribution assemblies (PENDAs). PENDAs have the following criteria: used for the distribution of electrical energy in three phase systems for which the

49、 rated voltage does not exceed 1 000 V a.c. (see Figure 101 for a typical distribution network); stationary; open ASSEMBLIES are not covered by this standard; suitable for installation in places where only skilled persons have access for their use, however, outdoor types may be installed in situations that are accessible to ordinary persons; for indoor or outdoor use. The object of this standard