IEC 61439-1-2011 Low-voltage switchgear and controlgear assemblies - Part 1 General rules《低压开关设备和控制设备组件.第1部分 一般规则》.pdf

《IEC 61439-1-2011 Low-voltage switchgear and controlgear assemblies - Part 1 General rules《低压开关设备和控制设备组件.第1部分 一般规则》.pdf》由会员分享，可在线阅读，更多相关《IEC 61439-1-2011 Low-voltage switchgear and controlgear assemblies - Part 1 General rules《低压开关设备和控制设备组件.第1部分 一般规则》.pdf（288页珍藏版）》请在麦多课文档分享上搜索。

1、 IEC 61439-1 Edition 2.0 2011-08 INTERNATIONAL STANDARD NORME INTERNATIONALE Low-voltage switchgear and controlgear assemblies Part 1: General rules Ensembles dappareillage basse tension Partie 1: Rgles gnrales IEC 61439-1:2011 colour inside THIS PUBLICATION IS COPYRIGHT PROTECTED Copyright 2011 IEC

2、, Geneva, Switzerland All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either IEC or IECs member National Committe

3、e in the country of the requester. If you have any questions about IEC copyright or have an enquiry about obtaining additional rights to this publication, please contact the address below or your local IEC member National Committee for further information. Droits de reproduction rservs. Sauf indicat

4、ion contraire, aucune partie de cette publication ne peut tre reproduite ni utilise sous quelque forme que ce soit et par aucun procd, lectronique ou mcanique, y compris la photocopie et les microfilms, sans laccord crit de la CEI ou du Comit national de la CEI du pays du demandeur. Si vous avez des

5、 questions sur le copyright de la CEI ou si vous dsirez obtenir des droits supplmentaires sur cette publication, utilisez les coordonnes ci-aprs ou contactez le Comit national de la CEI de votre pays de rsidence. IEC Central Office 3, rue de Varemb CH-1211 Geneva 20 Switzerland Email: inmailiec.ch W

6、eb: www.iec.ch About the IEC The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes International Standards for all electrical, electronic and related technologies. About IEC publications The technical content of IEC publications is kept un

7、der constant review by the IEC. Please make sure that you have the latest edition, a corrigenda or an amendment might have been published. Catalogue of IEC publications: www.iec.ch/searchpub The IEC on-line Catalogue enables you to search by a variety of criteria (reference number, text, technical c

8、ommittee,). It also gives information on projects, withdrawn and replaced publications. IEC Just Published: www.iec.ch/online_news/justpub Stay up to date on all new IEC publications. Just Published details twice a month all new publications released. Available on-line and also by email. Electropedi

9、a: www.electropedia.org The worlds leading online dictionary of electronic and electrical terms containing more than 20 000 terms and definitions in English and French, with equivalent terms in additional languages. Also known as the International Electrotechnical Vocabulary online. Customer Service

10、 Centre: www.iec.ch/webstore/custserv If you wish to give us your feedback on this publication or need further assistance, please visit the Customer Service Centre FAQ or contact us: Email: csciec.ch Tel.: +41 22 919 02 11 Fax: +41 22 919 03 00 A propos de la CEI La Commission Electrotechnique Inter

11、nationale (CEI) est la premire organisation mondiale qui labore et publie des normes internationales pour tout ce qui a trait llectricit, llectronique et aux technologies apparentes. A propos des publications CEI Le contenu technique des publications de la CEI est constamment revu. Veuillez vous ass

12、urer que vous possdez ldition la plus rcente, un corrigendum ou amendement peut avoir t publi. Catalogue des publications de la CEI: www.iec.ch/searchpub/cur_fut-f.htm Le Catalogue en-ligne de la CEI vous permet deffectuer des recherches en utilisant diffrents critres (numro de rfrence, texte, comit

13、 dtudes,). Il donne aussi des informations sur les projets et les publications retires ou remplaces. Just Published CEI: www.iec.ch/online_news/justpub Restez inform sur les nouvelles publications de la CEI. Just Published dtaille deux fois par mois les nouvelles publications parues. Disponible en-l

14、igne et aussi par email. Electropedia: www.electropedia.org Le premier dictionnaire en ligne au monde de termes lectroniques et lectriques. Il contient plus de 20 000 termes et dfinitions en anglais et en franais, ainsi que les termes quivalents dans les langues additionnelles. Egalement appel Vocab

15、ulaire Electrotechnique International en ligne. Service Clients: www.iec.ch/webstore/custserv/custserv_entry-f.htm Si vous dsirez nous donner des commentaires sur cette publication ou si vous avez des questions, visitez le FAQ du Service clients ou contactez-nous: Email: csciec.ch Tl.: +41 22 919 02

16、 11 Fax: +41 22 919 03 00 IEC 61439-1 Edition 2.0 2011-08 INTERNATIONAL STANDARD NORME INTERNATIONALE Low-voltage switchgear and controlgear assemblies Part 1: General rules Ensembles dappareillage basse tension Partie 1: Rgles gnrales INTERNATIONAL ELECTROTECHNICAL COMMISSION COMMISSION ELECTROTECH

17、NIQUE INTERNATIONALE XG ICS 29.130.20 PRICE CODE CODE PRIX ISBN 978-2-88912-634-7 Registered trademark of the International Electrotechnical Commission Marque dpose de la Commission Electrotechnique Internationale colour inside 2 61439-1 IEC:2011 CONTENTS FOREWORD . 8 INTRODUCTION . 11 1 Scope . 12

18、2 Normative references . 12 3 Terms and definitions . 15 3.1 General terms . 15 3.2 Constructional units of ASSEMBLIES 17 3.3 External design of ASSEMBLIES . 18 3.4 Structural parts of ASSEMBLIES . 18 3.5 Conditions of installation of ASSEMBLIES . 20 3.6 Insulation characteristics . 20 3.7 Protectio

19、n against electric shock . 23 3.8 Characteristics 25 3.9 Verification 27 3.10 Manufacturer/user . 28 4 Symbols and abbreviations . 28 5 Interface characteristics . 29 5.1 General . 29 5.2 Voltage ratings 29 5.2.1 Rated voltage (U n ) (of the ASSEMBLY) 29 5.2.2 Rated operational voltage (U e ) (of a

20、circuit of an ASSEMBLY) 29 5.2.3 Rated insulation voltage (U i ) (of a circuit of an ASSEMBLY) . 29 5.2.4 Rated impulse withstand voltage (U imp ) (of the ASSEMBLY) 29 5.3 Current ratings 30 5.3.1 Rated current of the ASSEMBLY (I nA ) 30 5.3.2 Rated current of a circuit (I nc ) . 30 5.3.3 Rated peak

21、 withstand current (I pk ) 30 5.3.4 Rated short-time withstand current (I cw ) (of a circuit of an ASSEMBLY) . 30 5.3.5 Rated conditional short-circuit current of an ASSEMBLY (I cc ) . 30 5.4 Rated diversity factor (RDF) 31 5.5 Rated frequency (f n ) 31 5.6 Other characteristics . 31 6 Information .

22、 32 6.1 ASSEMBLY designation marking 32 6.2 Documentation 32 6.2.1 Information relating to the ASSEMBLY 32 6.2.2 Instructions for handling, installation, operation and maintenance . 32 6.3 Device and/or component identification . 33 7 Service conditions 33 7.1 Normal service conditions . 33 7.1.1 Am

23、bient air temperature 33 7.1.2 Humidity conditions . 33 7.1.3 Pollution degree 33 7.1.4 Altitude 34 7.2 Special service conditions . 34 7.3 Conditions during transport, storage and installation . 35 61439-1 IEC:2011 3 8 Constructional requirements . 35 8.1 Strength of materials and parts 35 8.1.1 Ge

24、neral . 35 8.1.2 Protection against corrosion 35 8.1.3 Properties of insulating materials . 35 8.1.4 Resistance to ultra-violet radiation . 36 8.1.5 Mechanical strength 36 8.1.6 Lifting provision . 36 8.2 Degree of protection provided by an ASSEMBLY enclosure 36 8.2.1 Protection against mechanical i

25、mpact 36 8.2.2 Protection against contact with live parts, ingress of solid foreign bodies and water . 36 8.2.3 ASSEMBLY with removable parts 37 8.3 Clearances and creepage distances 37 8.3.1 General . 37 8.3.2 Clearances 38 8.3.3 Creepage distances . 38 8.4 Protection against electric shock . 39 8.

26、4.1 General . 39 8.4.2 Basic protection . 39 8.4.3 Fault protection . 40 8.4.4 Protection by total insulation 42 8.4.5 Limitation of steady-state touch current and charge . 43 8.4.6 Operating and servicing conditions 43 8.5 Incorporation of switching devices and components 45 8.5.1 Fixed parts 45 8.

27、5.2 Removable parts . 45 8.5.3 Selection of switching devices and components . 46 8.5.4 Installation of switching devices and components 46 8.5.5 Accessibility 46 8.5.6 Barriers . 47 8.5.7 Direction of operation and indication of switching positions 47 8.5.8 Indicator lights and push-buttons . 47 8.

28、6 Internal electrical circuits and connections 47 8.6.1 Main circuits 47 8.6.2 Auxiliary circuits 48 8.6.3 Bare and insulated conductors 48 8.6.4 Selection and installation of non-protected live conductors to reduce the possibility of short-circuits . 49 8.6.5 Identification of the conductors of mai

29、n and auxiliary circuits . 49 8.6.6 Identification of the protective conductor (PE, PEN) and of the neutral conductor (N) of the main circuits 49 8.7 Cooling 49 8.8 Terminals for external conductors 49 9 Performance requirements . 51 9.1 Dielectric properties 51 9.1.1 General . 51 9.1.2 Power-freque

30、ncy withstand voltage . 51 9.1.3 Impulse withstand voltage . 51 4 61439-1 IEC:2011 9.1.4 Protection of surge protective devices . 51 9.2 Temperature rise limits 52 9.3 Short-circuit protection and short-circuit withstand strength . 52 9.3.1 General . 52 9.3.2 Information concerning short-circuit wit

31、hstand strength . 52 9.3.3 Relationship between peak current and short-time current . 53 9.3.4 Co-ordination of protective devices 53 9.4 Electromagnetic compatibility (EMC) . 53 10 Design verification 54 10.1 General . 54 10.2 Strength of materials and parts 55 10.2.1 General . 55 10.2.2 Resistance

32、 to corrosion . 55 10.2.3 Properties of insulating materials . 56 10.2.4 Resistance to ultra-violet (UV) radiation. 58 10.2.5 Lifting 58 10.2.6 Mechanical impact . 59 10.2.7 Marking . 59 10.3 Degree of protection of ASSEMBLIES . 59 10.4 Clearances and creepage distances 59 10.5 Protection against el

33、ectric shock and integrity of protective circuits . 60 10.5.1 Effectiveness of the protective circuit. 60 10.5.2 Effective earth continuity between the exposed conductive parts of the ASSEMBLY and the protective circuit 60 10.5.3 Short-circuit withstand strength of the protective circuit . 60 10.6 I

34、ncorporation of switching devices and components 61 10.6.1 General . 61 10.6.2 Electromagnetic compatibility 61 10.7 Internal electrical circuits and connections 61 10.8 Terminals for external conductors 61 10.9 Dielectric properties 61 10.9.1 General . 61 10.9.2 Power-frequency withstand voltage .

35、61 10.9.3 Impulse withstand voltage . 62 10.9.4 Testing of enclosures made of insulating material 64 10.9.5 External operating handles of insulating material . 64 10.10 Verification of temperature rise 64 10.10.1 General . 64 10.10.2 Verification by testing 64 10.10.3 Derivation of ratings for simil

36、ar variants . 70 10.10.4 Verification assessment . 71 10.11 Short-circuit withstand strength . 74 10.11.1 General . 74 10.11.2 Circuits of ASSEMBLIES which are exempted from the verification of the short-circuit withstand strength 74 10.11.3 Verification by comparison with a reference design Utilisi

37、ng a check list . 75 10.11.4 Verification by comparison with a reference design Utilising calculation . 75 10.11.5 Verification by test . 75 61439-1 IEC:2011 5 10.12 Electromagnetic compatibility (EMC) . 80 10.13 Mechanical operation 80 11 Routine verification . 80 11.1 General . 80 11.2 Degree of p

38、rotection of enclosures 81 11.3 Clearances and creepage distances 81 11.4 Protection against electric shock and integrity of protective circuits . 81 11.5 Incorporation of built-in components 81 11.6 Internal electrical circuits and connections 81 11.7 Terminals for external conductors 81 11.8 Mecha

39、nical operation 82 11.9 Dielectric properties 82 11.10 Wiring, operational performance and function 82 Annex A (normative) Minimum and maximum cross-section of copper conductors suitable for connection to terminals for external conductors (see 8.8) . 90 Annex B (normative) Method of calculating the

40、cross-sectional area of protective conductors with regard to thermal stresses due to currents of short duration 91 Annex C (informative) User information template . 92 Annex D (informative) Design verification 96 Annex E (informative) Rated diversity factor 97 Annex F (normative) Measurement of clea

41、rances and creepage distances 106 Annex G (normative) Correlation between the nominal voltage of the supply system and the rated impulse withstand voltage of the equipment 111 Annex H (informative) Operating current and power loss of copper conductors 113 Annex I (Void) . 115 Annex J (normative) Ele

42、ctromagnetic compatibility (EMC) 116 Annex K (normative) Protection by electrical separation. 123 Annex L (informative) Clearances and creepage distances for North American region . 126 Annex M (informative) North American temperature rise limits . 127 Annex N (normative) Operating current and power

43、 loss of bare copper bars 128 Annex O (informative) Guidance on temperature rise verification . 130 Annex P (normative) Verification of the short-circuit withstand strength of busbar structures by comparison with a tested reference design by calculation 135 Bibliography 139 Figure E.1 Typical ASSEMB

44、LY 98 Figure E.2 Example 1: Table E.1 Functional unit loading for an ASSEMBLY with a rated diversity factor of 0,8 . 100 Figure E.3 Example 2: Table E.1 Functional unit loading for an ASSEMBLY with a rated diversity factor of 0,8 . 101 Figure E.4 Example 3: Table E.1 Functional unit loading for an A

45、SSEMBLY with a rated diversity factor of 0,8 . 102 Figure E.5 Example 4: Table E.1 Functional unit loading for an ASSEMBLY with a rated diversity factor of 0,8 . 103 Figure E.6 Example of average heating effect calculation 104 Figure E.7 Example graph for the relation between the equivalent RDF and

46、the parameters at intermittent duty at t 1= 0,5 s, I 1= 7*I 2at different cycle times 105 6 61439-1 IEC:2011 Figure E.8 Example graph for the relation between the equivalent RDF and the parameters at intermittent duty at I 1= I 2(no starting overcurrent) 105 Figure F.1 Measurement of ribs . 110 Figu

47、re J.1 Examples of ports . 116 Figure O.1 Temperature rise verification methods 134 Figure P.1 Tested busbar structure (TS) 135 Figure P.2 Non tested busbar structure (NTS) 136 Figure P.3 Angular busbar configuration with supports at the corners 138 Table 1 Minimum clearances in air a(8.3.2) . 82 Ta

48、ble 2 Minimum creepage distances (8.3.3) . 83 Table 3 Cross-sectional area of a copper protective conductor (8.4.3.2.2) . 83 Table 4 Conductor selection and installation requirements (8.6.4) 84 Table 5 Minimum terminal capacity for copper protective conductors (PE, PEN) (8.8) 84 Table 6 Temperature-

49、rise limits (9.2) . 85 Table 7 Values for the factor n a(9.3.3) . 86 Table 8 Power-frequency withstand voltage for main circuits (10.9.2) 86 Table 9 Power-frequency withstand voltage for auxiliary and control circuits (10.9.2) . 86 Table 10 Impulse withstand test voltages (10.9.3) 87 Table 11 Copper test conductors for rated currents up to 400 A inclusive (10.10.2.3.2) . 87 Table 12 Copper te