IEC 61169-18-2011 Radio-frequency connectors - Part 18 Sectional specification - Radio frequency coaxial connectors of type SSMA《射频连接器.第18部分 分规范.扩频多址(SSMA)型射频同轴连接器》.pdf

《IEC 61169-18-2011 Radio-frequency connectors - Part 18 Sectional specification - Radio frequency coaxial connectors of type SSMA《射频连接器.第18部分 分规范.扩频多址(SSMA)型射频同轴连接器》.pdf》由会员分享，可在线阅读，更多相关《IEC 61169-18-2011 Radio-frequency connectors - Part 18 Sectional specification - Radio frequency coaxial connectors of type SSMA《射频连接器.第18部分 分规范.扩频多址(SSMA)型射频同轴连接器》.pdf（54页珍藏版）》请在麦多课文档分享上搜索。

1、 IEC 61169-18 Edition 1.0 2011-01 INTERNATIONAL STANDARD NORME INTERNATIONALE Radio-frequency connectors Part 18: Sectional specification Radio frequency coaxial connectors of type SSMA Connecteurs pour frquences radiolectriques Partie 18: Spcification intermdiaire Connecteurs coaxiaux pour frquence

2、s radiolectriques de type SSMA IEC61169-18:2011 colourinsideTHIS PUBLICATION IS COPYRIGHT PROTECTED Copyright 2011 IEC, Geneva, Switzerland All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical

3、, including photocopying and microfilm, without permission in writing from either IEC or IECs member National Committee in the country of the requester. If you have any questions about IEC copyright or have an enquiry about obtaining additional rights to this publication, please contact the address

4、below or your local IEC member National Committee for further information. Droits de reproduction rservs. Sauf indication contraire, aucune partie de cette publication ne peut tre reproduite ni utilise sous quelque forme que ce soit et par aucun procd, lectronique ou mcanique, y compris la photocopi

5、e et les microfilms, sans laccord crit de la CEI ou du Comit national de la CEI du pays du demandeur. Si vous avez des questions sur le copyright de la CEI ou si vous dsirez obtenir des droits supplmentaires sur cette publication, utilisez les coordonnes ci-aprs ou contactez le Comit national de la

6、CEI de votre pays de rsidence. IEC Central Office 3, rue de Varemb CH-1211 Geneva 20 Switzerland Email: inmailiec.ch Web: www.iec.ch About the IEC The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes International Standards for all electr

7、ical, electronic and related technologies. About IEC publications The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the latest edition, a corrigenda or an amendment might have been published. Catalogue of IEC publications: www.iec.ch/s

8、earchpub The IEC on-line Catalogue enables you to search by a variety of criteria (reference number, text, technical committee,). It also gives information on projects, withdrawn and replaced publications. IEC Just Published: www.iec.ch/online_news/justpub Stay up to date on all new IEC publications

9、. Just Published details twice a month all new publications released. Available on-line and also by email. Electropedia: www.electropedia.org The worlds leading online dictionary of electronic and electrical terms containing more than 20 000 terms and definitions in English and French, with equivale

10、nt terms in additional languages. Also known as the International Electrotechnical Vocabulary online. Customer Service Centre: www.iec.ch/webstore/custserv If you wish to give us your feedback on this publication or need further assistance, please visit the Customer Service Centre FAQ or contact us:

11、 Email: csciec.ch Tel.: +41 22 919 02 11 Fax: +41 22 919 03 00 A propos de la CEI La Commission Electrotechnique Internationale (CEI) est la premire organisation mondiale qui labore et publie des normes internationales pour tout ce qui a trait llectricit, llectronique et aux technologies apparentes.

12、 A propos des publications CEI Le contenu technique des publications de la CEI est constamment revu. Veuillez vous assurer que vous possdez ldition la plus rcente, un corrigendum ou amendement peut avoir t publi. Catalogue des publications de la CEI: www.iec.ch/searchpub/cur_fut-f.htm Le Catalogue e

13、n-ligne de la CEI vous permet deffectuer des recherches en utilisant diffrents critres (numro de rfrence, texte, comit dtudes,). Il donne aussi des informations sur les projets et les publications retires ou remplaces. Just Published CEI: www.iec.ch/online_news/justpub Restez inform sur les nouvelle

14、s publications de la CEI. Just Published dtaille deux fois par mois les nouvelles publications parues. Disponible en-ligne et aussi par email. Electropedia: www.electropedia.org Le premier dictionnaire en ligne au monde de termes lectroniques et lectriques. Il contient plus de 20 000 termes et dfini

15、tions en anglais et en franais, ainsi que les termes quivalents dans les langues additionnelles. Egalement appel Vocabulaire Electrotechnique International en ligne. Service Clients: www.iec.ch/webstore/custserv/custserv_entry-f.htm Si vous dsirez nous donner des commentaires sur cette publication o

16、u si vous avez des questions, visitez le FAQ du Service clients ou contactez-nous: Email: csciec.ch Tl.: +41 22 919 02 11 Fax: +41 22 919 03 00 IEC 61169-18 Edition 1.0 2011-01 INTERNATIONAL STANDARD NORME INTERNATIONALE Radio-frequency connectors Part 18: Sectional specification Radio frequency coa

17、xial connectors of type SSMA Connecteurs pour frquences radiolectriques Partie 18: Spcification intermdiaire Connecteurs coaxiaux pour frquences radiolectriques de type SSMA INTERNATIONAL ELECTROTECHNICAL COMMISSION COMMISSION ELECTROTECHNIQUE INTERNATIONALE T ICS 33.120.30 PRICE CODE CODE PRIX ISBN

18、 978-2-88912-319-3 Registered trademark of the International Electrotechnical Commission Marque dpose de la Commission Electrotechnique Internationale colourinside 2 61169-18 IEC:2011 CONTENTS FOREWORD . 4 1 Scope . 6 2 Normative references . 6 3 Mating face and gauge information . 6 3.1 Dimensions

19、- High performance connectors Grade 1 6 3.1.1 Connector with pin-centre contact 7 3.1.2 Connector with socket-centre contact 8 3.2 Gauges . 9 3.2.1 Gauge pins for socket-centre contact . 9 3.2.2 Test procedure 9 3.3 Dimensions - standard test connectors Grade 0 . 10 3.3.1 Connector with pin-centre c

20、ontact 10 3.3.2 Connector with socket-centre contact 11 4 Quality assessment procedure 12 4.1 General . 12 4.2 Standard ratings and characteristics (see Clause 6 of IEC 61169-1) 12 4.3 Test schedule and inspection requirements Acceptance tests . 15 4.3.1 Acceptance tests . 15 4.3.2 Periodic tests 15

21、 4.4 Procedures 18 4.4.1 Quality conformance inspection . 18 4.4.2 Qualification approval and its maintenance 18 5 Instructions for preparation of detail specifications . 18 5.1 General . 18 5.2 Identification of the component 18 5.3 Performance 19 5.4 Marking, ordering information and related matte

22、rs . 19 5.5 Selection of tests, test conditions and severities 19 5.6 Blank detail specification pro-forma for type SSMA connector . 20 Figure 1 Connector with pin-centre contact (for dimensions and notes, see Table 1) 7 Figure 2 Connector with socket-centre contact (for dimensions and notes, see Ta

23、ble 2) 8 Figure 3 Gauge pins for socket-centre contact (for dimensions and notes, see Table 3) 9 Figure 4 Connector with pin-centre contact (for dimensions and notes, see Table 4) 10 Figure 5 Connector with socket-centre contact (for dimensions and notes, see Table 5) 11 61169-18 IEC:2011 3 Table 1

24、Dimensions of connector with pin-centre contact . 7 Table 2 Dimensions of connector with socket-centre contact 8 Table 3 Dimensions of gauge pins for socket-centre contact 9 Table 4 Dimensions of connector with pin-centre contact . 10 Table 5 Dimensions of connector with socket-centre contact 12 Tab

25、le 6 Rating and characteristics . 13 Table 7 Acceptance tests . 15 Table 8 Periodic tests 16 4 61169-18 IEC:2011 INTERNATIONAL ELECTROTECHNICAL COMMISSION _ RADIO-FREQUENCY CONNECTORS Part 18: Sectional specification Radio frequency coaxial connectors of type SSMA FOREWORD 1) The International Elect

26、rotechnical Commission (IEC) is a worldwide organization for standardization comprising all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international co-operation on all questions concerning standardization in the electrical and electronic fields.

27、To this end and in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their preparation is entrusted to technical committees; any IEC Nat

28、ional Committee interested in the subject dealt with may participate in this preparatory work. International, governmental and non-governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for Standardization (

29、ISO) in accordance with conditions determined by agreement between the two organizations. 2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international consensus of opinion on the relevant subjects since each technical committee has representation

30、 from all interested IEC National Committees. 3) IEC Publications have the form of recommendations for international use and are accepted by IEC National Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC Publications is accurate, IEC cannot b

31、e held responsible for the way in which they are used or for any misinterpretation by any end user. 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications transparently to the maximum extent possible in their national and regional publications. A

32、ny divergence between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter. 5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity assessment services and, in some areas, access

33、to IEC marks of conformity. IEC is not responsible for any services carried out by independent certification bodies. 6) All users should ensure that they have the latest edition of this publication. 7) No liability shall attach to IEC or its directors, employees, servants or agents including individ

34、ual experts and members of its technical committees and IEC National Committees for any personal injury, property damage or other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and expenses arising out of the publication, use of, or reliance upon, th

35、is IEC Publication or any other IEC Publications. 8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is indispensable for the correct application of this publication. 9) Attention is drawn to the possibility that some of the elements of th

36、is IEC Publication may be the subject of patent rights. IEC shall not be held responsible for identifying any or all such patent rights. International Standard IEC 61169-18 has been prepared by subcommittee 46F: R.F. and microwave passive components, of IEC technical committee 46: Cables, wires, wav

37、eguides, R.F. connectors, R.F. and microwave passive components and accessories. This first edition cancels and replaces IEC/PAS 61169-18, published in 2009, of which it constitutes a minor revision. The only change between the PAS and this standard is the removal of inch dimensions for each of the

38、figures. The text of this standard is based on the following documents: CDV Report on voting 46F/136/CDV 46F/162/RVC Full information on the voting for the approval of this standard can be found in the report on voting indicated in the above table. 61169-18 IEC:2011 5 The French version of this stan

39、dard has not been voted upon. This publication has been drafted in accordance with the ISO/IEC Directives, Part 2. A list of all parts of the IEC 61169 series, published under the general title Radio-frequency connectors, can be found on the IEC website. The committee has decided that the contents o

40、f this publication will remain unchanged until the stability date indicated on the IEC web site under “http:/webstore.iec.ch“ in the data related to the specific publication. At this date, the publication will be reconfirmed, withdrawn, replaced by a revised edition, or amended. IMPORTANT The colour

41、 inside logo on the cover page of this publication indicates that it contains colours which are considered to be useful for the correct understanding of its contents. Users should therefore print this document using a colour printer. 6 61169-18 IEC:2011 RADIO-FREQUENCY CONNECTORS Part 18: Sectional

42、specification Radio frequency coaxial connectors of type SSMA 1 Scope SSMA series connectors with characteristic impedance 50 are used for millimeter wave applications, connecting with RF cables or micro strips. The operating frequency limit is up to 35 GHz. The coupling thread is 10-36 UNS thread.

43、This sectional specification provides information and rules for preparation of detail specification of SSMA series R.F connectors together with the pro-forma blank detail specification. It also prescribes mating face dimensions for grade 1 high performance connectors, dimensional detail of grade 0 s

44、tandard test connectors, gauging information and tests selected from IEC 61169-1 applicable to all detail specifications relating to SSMA series RF connectors. This specification indicates recommended performance characteristics to be considered when writing a detail specification and it covers test

45、 schedules and inspection requirements for assessment levels M and H. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced d

46、ocument (including any amendments) applies. IEC 61169-1:19981992, Radio-frequency connectors Part 1: Generic specification General requirements and measuring methods1Amendment 1 (1996) Amendment 2 (1997) 3 Mating face and gauge information 3.1 Dimensions High performance connectors Grade 1 All undim

47、ensioned pictorial configurations are for reference purpose only. _ 1There exists a consolidated edition 1.2 (1998) that comprises IEC 61169-1:1992, its Amendment 1:1996 and its Amendment 2:1997. 61169-18 IEC:2011 7 3.1.1 Connector with pin-centre contact Not e 110-36UNS-2B10-36UNS-2B( C h a mf e r

48、)Gas k et ( Not e 4)( Not e 2)Not e 3El ectri cal and Mechani cal r ef er enceElectrical and mechanical reference Gasket (Note 4) Note 1 g i c f e l n d Note 2) bha10-36UNS-2Bjm( hamfer Note 3IEC 053/11 Figure 1 Connector with pin-centre contact (for dimensions and notes, see Table 1) Table 1 Dimens

49、ions of connector with pin-centre contact Ref. mm Min. Max. a 4,98 - b 3,15 3,22 c 0,38 1,14 d - 3,43 e 2,54 - f 0,00 0,18 g 0,00 0,25 h 2,79 nominal i 0,08 max. 45 or R0,08 max. j 0,495 0,528 l 1,00 - m - 0,25 n - 1,65 8 61169-18 IEC:2011 NOTE 1 Dimensions are such that the reference planes coincide and the connectors meet the required enviro