IEC 61169-1-2013 Radio frequency connectors - Part 1 Generic specification - General requirements and measuring methods《射频连接器.第19部分 分规范.SSMB型射频同轴连接器》.pdf

《IEC 61169-1-2013 Radio frequency connectors - Part 1 Generic specification - General requirements and measuring methods《射频连接器.第19部分 分规范.SSMB型射频同轴连接器》.pdf》由会员分享，可在线阅读，更多相关《IEC 61169-1-2013 Radio frequency connectors - Part 1 Generic specification - General requirements and measuring methods《射频连接器.第19部分 分规范.SSMB型射频同轴连接器》.pdf（64页珍藏版）》请在麦多课文档分享上搜索。

1、 IEC 61169-1 Edition 2.0 2013-07 INTERNATIONAL STANDARD Radio frequency connectors Part 1: Generic specification General requirements and measuring methods IEC 61169-1:2013(E) colour inside THIS PUBLICATION IS COPYRIGHT PROTECTED Copyright 2013 IEC, Geneva, Switzerland All rights reserved. Unless ot

2、herwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either IEC or IECs member National Committee in the country of the requester. If you have any q

3、uestions about IEC copyright or have an enquiry about obtaining additional rights to this publication, please contact the address below or your local IEC member National Committee for further information. IEC Central Office Tel.: +41 22 919 02 11 3, rue de Varemb Fax: +41 22 919 03 00 CH-1211 Geneva

4、 20 infoiec.ch Switzerland www.iec.ch About the IEC The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes International Standards for all electrical, electronic and related technologies. About IEC publications The technical content of IEC

5、publications is kept under constant review by the IEC. Please make sure that you have the latest edition, a corrigenda or an amendment might have been published. Useful links: IEC publications search - www.iec.ch/searchpub The advanced search enables you to find IEC publications by a variety of crit

6、eria (reference number, text, technical committee,). It also gives information on projects, replaced and withdrawn publications. IEC Just Published - webstore.iec.ch/justpublished Stay up to date on all new IEC publications. Just Published details all new publications released. Available on-line and

7、 also once a month by email. Electropedia - www.electropedia.org The worlds leading online dictionary of electronic and electrical terms containing more than 30 000 terms and definitions in English and French, with equivalent terms in additional languages. Also known as the International Electrotech

8、nical Vocabulary (IEV) on-line. Customer Service Centre - webstore.iec.ch/csc If you wish to give us your feedback on this publication or need further assistance, please contact the Customer Service Centre: csciec.ch. IEC 61169-1 Edition 2.0 2013-07 INTERNATIONAL STANDARD Radio frequency connectors

9、Part 1: Generic specification General requirements and measuring methods INTERNATIONAL ELECTROTECHNICAL COMMISSION XA ICS 33.120.30 PRICE CODE ISBN 978-2-8322-0925-7 Registered trademark of the International Electrotechnical Commission Warning! Make sure that you obtained this publication from an au

10、thorized distributor. colour inside 2 61169-1 IEC:2013(E) CONTENTS FOREWORD . 5 1 Scope . 7 2 Normative references . 7 3 Terms and definitions . 8 General, parts of connectors . 8 3.1Basic connector terms . 9 3.2Constructional terms . 10 3.3Sealing 11 3.4Miscellaneous terms 11 3.5General electrotech

11、nical terms 12 3.6 4 Units, symbols and dimensions . 12 Units and symbols . 12 4.1Dimensions . 13 4.2Details to be provided in relevant specifications 13 4.2.1Dimensional units to be used in specifications . 13 4.2.2 5 Standards ratings and characteristics . 13 6 Classifications into climatic catego

12、ries 13 7 IEC type designation 14 8 Testing . 14 9 Test methods 14 Mechanical inspection . 14 9.1Visual inspection . 14 9.1.1Dimensions 15 9.1.2Electrical tests and measuring procedures 15 9.2Return loss 15 9.2.1Power rating 19 9.2.2Contact resistance, outer conductor and centre conductor continuity

13、 9.2.3 (mated cabled connectors) 20 Centre and outer conductor contact continuity under severe 9.2.4 mechanical conditioning 22 Insulation resistance 22 9.2.5Voltage proof . 23 9.2.6Screening effectiveness . 24 9.2.7Discharge test (corona test) . 24 9.2.8Intermodulation level (PIM) 25 9.2.9Surge wit

14、hstand . 26 9.2.10Mechanical tests and measuring procedures . 26 9.3General . 26 9.3.1Soldering . 26 9.3.2Vibration 26 9.3.3Insertion force (resilient contacts) 27 9.3.4Centre contact captivation . 28 9.3.5Engagement and separation forces and torques 28 9.3.6Effectiveness of clamping device against

15、cable rotation (nutation of 9.3.7 cable end) . 29 Effectiveness of clamping device against cable pulling 29 9.3.861169-1 IEC:2013(E) 3 Effectiveness of clamping device against cable bending 30 9.3.9Effectiveness of clamping device against cable torsion 31 9.3.10Strength of coupling mechanism 32 9.3.

16、11Safety wire hole pull-out bending moment (and shearing force) . 32 9.3.12Bump . 33 9.3.13Shock 34 9.3.14Mechanical endurance . 35 9.3.15Climatic conditionings and tests 35 9.4Conditionings 35 9.4.1Climatic sequence . 36 9.4.2Damp heat, steady state 37 9.4.3Change of temperature 37 9.4.4High temper

17、ature endurance . 38 9.4.5Low temperature endurance 39 9.4.6Sealing non-hermetic sealed connectors 40 9.4.7Hermetically sealed connectors . 40 9.4.8Water immersion test . 41 9.4.9Salt mist 43 9.4.10Resistance to solvents and contaminating fluids 43 9.4.11Sulphur dioxide test . 45 9.4.12 10 Quality a

18、ssessment 46 General . 46 10.1Quality assessment steps 46 10.2Primary stage of manufacture 46 10.2.1Structurally similar components . 46 10.2.2General principle for obtaining quality conformance . 46 10.2.3Test schedule and inspection requirements . 46 10.3Acceptance tests . 46 10.3.1Periodic tests.

19、 48 10.3.2Procedures for quality conformance 49 10.4Quality conformance inspection . 49 10.4.1Quality conformance and its maintenance 49 10.4.2Test and measurement procedures . 49 10.5General . 49 10.5.1Schedule of basic test groupings for acceptance and periodic tests . 50 10.5.2Specifications 50 1

20、0.6Specification structures . 50 10.6.1Sectional specification (SS) . 50 10.6.2Detail specification (DS) 50 10.6.3Blank detail specification . 51 10.6.4Blank detail specification pro-forma for XXXX connectors 52 10.6.5 11 Marking 57 Marking of component . 57 11.1Marking and contents of package 57 11

21、.2 Annex A (informative) Simulated sea-water solution for use with salt mist test (marine environment, see 9.4.10.3) . 58 Bibliography 59 4 61169-1 IEC:2013(E) Figure 1 graphical symbols 16 Figure 2 General principle 16 Figure 3 Measuring set-up for two-connector procedure . 17 Figure 4 Example of a

22、 time domain reflectometer measurement recording . 18 Figure 5 Equipment set-up for the measurement of reflection in time domain . 19 Figure 6 Possible test arrangements 23 Figure 7 Measuring circuit for the discharge test 25 Figure 8 Test arrangement for nutation 29 Figure 9 Test arrangement for pu

23、lling 30 Figure 10 Bending 31 Figure 11 Cable torsion 31 Figure 12 Temperature curve profile 41 Figure 13 Container/jumper arrangement . 42 Table 1 Preferred climatic categories (see IEC 60068-1) 13 Table 2 Dielectric materials ratings 20 Table 3 Severities for vibration. 27 Table 4 Recommended seve

24、rities for bump 33 Table 5 Recommended severities for shocks . 34 Table 6 Recommended severities for low temperature tests . 39 Table 7 Fuels, lubricants, hydraulic fluids and anti-freeze agents . 44 Table 8 Cleaning agents and moisture repellents . 44 Table 9 Acceptance tests . 47 Table 10 Periodic

25、 tests 48 61169-1 IEC:2013(E) 5 INTERNATIONAL ELECTROTECHNICAL COMMISSION _ RADIO FREQUENCY CONNECTORS Part 1: Generic specification General requirements and measuring methods FOREWORD 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising a

26、ll national electrotechnical committees (IEC National Committees). The object of IEC is to promote international co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and in addition to other activities, IEC publishes International Standards, T

27、echnical Specifications, Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with may participate in this preparatory

28、work. International, governmental and non- governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for Standardization (ISO) in accordance with conditions determined by agreement between the two organizations

29、. 2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international consensus of opinion on the relevant subjects since each technical committee has representation from all interested IEC National Committees. 3) IEC Publications have the form of recom

30、mendations for international use and are accepted by IEC National Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any misinterpretation by an

31、y end user. 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications transparently to the maximum extent possible in their national and regional publications. Any divergence between any IEC Publication and the corresponding national or regional pub

32、lication shall be clearly indicated in the latter. 5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any services carried out by indep

33、endent certification bodies. 6) All users should ensure that they have the latest edition of this publication. 7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and members of its technical committees and IEC National Committees for any

34、personal injury, property damage or other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC Publications. 8) Attention is drawn to the Normative

35、 references cited in this publication. Use of the referenced publications is indispensable for the correct application of this publication. 9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent rights. IEC shall not be held responsibl

36、e for identifying any or all such patent rights. International Standard IEC 61169-1 has been prepared by subcommittee 46F: R.F. and microwave passive components, of IEC technical committee 46: Cables, wires, waveguides, R.F. connectors, R.F. and microwave passive components and accessories. This sec

37、ond edition cancels and replaces the first edition, published in 1992, its Amendments 1 (1996) and 2 (1997). This edition constitutes a technical revision. With respect to the previous edition, tests methods have been updated as well as terminology. The text of this standard is based on the followin

38、g documents: CDV Report on voting 46F/216/CDV 46F/226/RVC Full information on the voting for the approval of this standard can be found in the report on voting indicated in the above table. 6 61169-1 IEC:2013(E) This publication has been drafted in accordance with the ISO/IEC Directives, Part 2. A l

39、ist of all the parts in the IEC 61169 series, published under the general title Radio frequency connectors, can be found on the IEC website. The committee has decided that the contents of this publication will remain unchanged until the stability date indicated on the IEC web site under “http:/webst

40、ore.iec.ch“ in the data related to the specific publication. At this date, the publication will be reconfirmed, withdrawn, replaced by a revised edition, or amended. A bilingual version of this publication may be issued at a later date. IMPORTANT The colour inside logo on the cover page of this publ

41、ication indicates that it contains colours which are considered to be useful for the correct understanding of its contents. Users should therefore print this document using a colour printer. 61169-1 IEC:2013(E) 7 RADIO FREQUENCY CONNECTORS Part 1: Generic specification General requirements and measu

42、ring methods 1 Scope This part of IEC 61169, which is a generic specification, relates to radio frequency connectors for r.f. transmission lines for use in telecommunications, electronics and similar equipment. It provides the basis for the sectional standards, which apply to individual connector ty

43、pes. It is intended to establish uniform concepts and procedures concerning: terminology; standard ratings and characteristics; testing and measuring procedures concerning electrical, mechanical and climatic properties; classification of connectors with regard to climatic testing procedures involvin

44、g temperature and humidity. The test methods and procedures of this standard are intended for acceptance and type approval testing. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated re

45、ferences, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. IEC 60027 (all parts), Letter symbols to be used in electrical technology IEC 60050 (all parts), International Electrotechnical Vocabulary (available fr

46、om: http:/www.electropedia.org) IEC 60068-1, Environmental testing Part 1: General and guidance IEC 60068-2-1:1990, Environmental testing Part 2-1: Tests Test A: Cold 1IEC 60068-2-2:1974, Environmental testing Part 2-2: Tests Test B: Dry heat 2IEC 60068-2-6, Environmental testing Part 2-6: Tests Tes

47、t Fc: Vibration (sinusoidal) IEC 60068-2-11, Environmental testing Part 2-11: Tests Test Ka: Salt mist IEC 60068-2-13, Environmental testing Part 2-13: Tests Test M: Low air pressure IEC 60068-2-14:2009, Environmental testing Part 2-14: Tests Test N: Change of temperature IEC 60068-2-17, Environment

48、al testing Part 2-17: Tests Test Q: Sealing _ 1This publication has been withdrawn. 2This publication has been withdrawn. 8 61169-1 IEC:2013(E) IEC 60068-2-20, Environmental testing Part 2-20: Tests Test T: Test methods for solderability and resistance to soldering heat of devices with leads IEC 600

49、68-2-27, Environmental testing Part 2-27: Tests Test Ea and guidance: Shock IEC 60068-2-29, Environmental testing Part 2: Tests Test Eb and guidance: Bump IEC 60068-2-30, Environmental testing Part 2-30: Tests Test Db: Damp heat, cyclic (12 h + 12 h cycle) IEC 60068-2-42, Environmental testing Part 2-42: Tests Test Kc: Sulphur dioxide test for contacts and connections IEC 60068-2-52:19