IEC 60763-1-2010 Laminated pressbord for electrical purposes - Part 1 Definitions classification and general requirements《电气用途的层压板.第1部分 定义 分类和一般要求》.pdf

《IEC 60763-1-2010 Laminated pressbord for electrical purposes - Part 1 Definitions classification and general requirements《电气用途的层压板.第1部分 定义 分类和一般要求》.pdf》由会员分享，可在线阅读，更多相关《IEC 60763-1-2010 Laminated pressbord for electrical purposes - Part 1 Definitions classification and general requirements《电气用途的层压板.第1部分 定义 分类和一般要求》.pdf（16页珍藏版）》请在麦多课文档分享上搜索。

1、 IEC 60763-1 Edition 2.0 2010-08 INTERNATIONAL STANDARD NORME INTERNATIONALE Laminated pressboard for electrical purposes Part 1: Definitions, classification and general requirements Cartons comprims et contrecolls usages lectriques Partie 1: Dfinitions, classification et exigences gnrales IEC 60763

2、-1:2010 THIS PUBLICATION IS COPYRIGHT PROTECTED Copyright 2010 IEC, Geneva, Switzerland All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without perm

3、ission in writing from either IEC or IECs member National Committee in the country of the requester. If you have any questions about IEC copyright or have an enquiry about obtaining additional rights to this publication, please contact the address below or your local IEC member National Committee fo

4、r further information. Droits de reproduction rservs. Sauf indication contraire, aucune partie de cette publication ne peut tre reproduite ni utilise sous quelque forme que ce soit et par aucun procd, lectronique ou mcanique, y compris la photocopie et les microfilms, sans laccord crit de la CEI ou

5、du Comit national de la CEI du pays du demandeur. Si vous avez des questions sur le copyright de la CEI ou si vous dsirez obtenir des droits supplmentaires sur cette publication, utilisez les coordonnes ci-aprs ou contactez le Comit national de la CEI de votre pays de rsidence. IEC Central Office 3,

6、 rue de Varemb CH-1211 Geneva 20 Switzerland Email: inmailiec.ch Web: www.iec.ch About the IEC The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes International Standards for all electrical, electronic and related technologies. About IEC

7、 publications The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the latest edition, a corrigenda or an amendment might have been published. Catalogue of IEC publications: www.iec.ch/searchpub The IEC on-line Catalogue enables you to se

8、arch by a variety of criteria (reference number, text, technical committee,). It also gives information on projects, withdrawn and replaced publications. IEC Just Published: www.iec.ch/online_news/justpub Stay up to date on all new IEC publications. Just Published details twice a month all new publi

9、cations released. Available on-line and also by email. Electropedia: www.electropedia.org The worlds leading online dictionary of electronic and electrical terms containing more than 20 000 terms and definitions in English and French, with equivalent terms in additional languages. Also known as the

10、International Electrotechnical Vocabulary online. Customer Service Centre: www.iec.ch/webstore/custserv If you wish to give us your feedback on this publication or need further assistance, please visit the Customer Service Centre FAQ or contact us: Email: csciec.ch Tel.: +41 22 919 02 11 Fax: +41 22

11、 919 03 00 A propos de la CEI La Commission Electrotechnique Internationale (CEI) est la premire organisation mondiale qui labore et publie des normes internationales pour tout ce qui a trait llectricit, llectronique et aux technologies apparentes. A propos des publications CEI Le contenu technique

12、des publications de la CEI est constamment revu. Veuillez vous assurer que vous possdez ldition la plus rcente, un corrigendum ou amendement peut avoir t publi. Catalogue des publications de la CEI: www.iec.ch/searchpub/cur_fut-f.htm Le Catalogue en-ligne de la CEI vous permet deffectuer des recherc

13、hes en utilisant diffrents critres (numro de rfrence, texte, comit dtudes,). Il donne aussi des informations sur les projets et les publications retires ou remplaces. Just Published CEI: www.iec.ch/online_news/justpub Restez inform sur les nouvelles publications de la CEI. Just Published dtaille deu

14、x fois par mois les nouvelles publications parues. Disponible en-ligne et aussi par email. Electropedia: www.electropedia.org Le premier dictionnaire en ligne au monde de termes lectroniques et lectriques. Il contient plus de 20 000 termes et dfinitions en anglais et en franais, ainsi que les termes

15、 quivalents dans les langues additionnelles. Egalement appel Vocabulaire Electrotechnique International en ligne. Service Clients: www.iec.ch/webstore/custserv/custserv_entry-f.htm Si vous dsirez nous donner des commentaires sur cette publication ou si vous avez des questions, visitez le FAQ du Serv

16、ice clients ou contactez-nous: Email: csciec.ch Tl.: +41 22 919 02 11 Fax: +41 22 919 03 00 IEC 60763-1 Edition 2.0 2010-08 INTERNATIONAL STANDARD NORME INTERNATIONALE Laminated pressboard for electrical purposes Part 1: Definitions, classification and general requirements Cartons comprims et contre

17、colls usages lectriques Partie 1: Dfinitions, classification et exigences gnrales INTERNATIONAL ELECTROTECHNICAL COMMISSION COMMISSION ELECTROTECHNIQUE INTERNATIONALE F ICS 29.035.10 PRICE CODE CODE PRIX ISBN 978-2-88912-145-8 Registered trademark of the International Electrotechnical Commission Mar

18、que dpose de la Commission Electrotechnique Internationale 2 60763-1 IEC:2010 INTERNATIONAL ELECTROTECHNICAL COMMISSION _ LAMINATED PRESSBOARD FOR ELECTRICAL PURPOSES Part 1: Definitions, classification and general requirements FOREWORD 1) The International Electrotechnical Commission (IEC) is a wor

19、ldwide organization for standardization comprising all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and in addition to other

20、activities, IEC publishes International Standards, Technical Specifications, Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested in the sub

21、ject dealt with may participate in this preparatory work. International, governmental and non- governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for Standardization (ISO) in accordance with conditions d

22、etermined by agreement between the two organizations. 2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international consensus of opinion on the relevant subjects since each technical committee has representation from all interested IEC National Co

23、mmittees. 3) IEC Publications have the form of recommendations for international use and are accepted by IEC National Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC Publications is accurate, IEC cannot be held responsible for the way in wh

24、ich they are used or for any misinterpretation by any end user. 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications transparently to the maximum extent possible in their national and regional publications. Any divergence between any IEC Public

25、ation and the corresponding national or regional publication shall be clearly indicated in the latter. 5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity assessment services and, in some areas, access to IEC marks of conformity. IEC is n

26、ot responsible for any services carried out by independent certification bodies. 6) All users should ensure that they have the latest edition of this publication. 7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and members of its techn

27、ical committees and IEC National Committees for any personal injury, property damage or other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC

28、Publications. 8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is indispensable for the correct application of this publication. 9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subjec

29、t of patent rights. IEC shall not be held responsible for identifying any or all such patent rights. International Standard IEC 60763-1 has been prepared by IEC technical committee 15: Solid electrical insulating materials. This second edition cancels and replaces the first edition published in 1983

30、. This edition constitutes a technical revision. The main changes with respect to the previous edition are as follows: the specification was brought in line with the second edition of IEC 60641-1(2007). The text of this standard is based on the following documents: CDV Report on voting 15/536/CDV 15

31、/566/RVC Full information on the voting for the approval of this standard can be found in the report on voting indicated in the above table. 60763-1 IEC:2010 3 This publication has been drafted in accordance with the ISO/IEC Directives, Part 2. Future standards in this series will carry the new gene

32、ral title as cited above. Titles of existing standards in this series will be updated at the time of the next edition. A list of all the parts in the IEC 60763 series can be found on the IEC website. The committee has decided that the contents of this publication will remain unchanged until the stab

33、ility date indicated on the IEC web site under “http:/webstore.iec.ch“ in the data related to the specific publication. At this date, the publication will be reconfirmed, withdrawn, replaced by a revised edition, or amended. 4 60763-1 IEC:2010 LAMINATED PRESSBOARD FOR ELECTRICAL PURPOSES Part 1: Def

34、initions, classification and general requirements 1 Scope This part of IEC 60763 contains the definitions required for the understanding of all three parts of IEC 60763, the classification of material into types, and the general requirements applicable to all material covered by the standard. Materi

35、als which conform to this specification meet established levels of performance. However, the selection of a material by a user for a specific application should be based on the actual requirements necessary for adequate performance in that application and not based on this specification alone. 2 Nor

36、mative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. IEC 60641-1:2007, Pressboard an

37、d presspaper for electrical purposes Part 1: Definitions and general requirements 3 Terms and definitions For the purposes of this document the following definitions apply: 3.1 pressboard board normally made on an intermittent board machine from pulp made entirely from vegetable origin of high chemi

38、cal purity. It is characterized by its relatively high density, even thickness, surface smoothness, high mechanical strength, flexibility, ageing resistance and electrical insulating properties. The surface may be smooth or textured 3.2 laminated pressboard board built up from sheets of pressboard b

39、onded with an adhesive 4 Classification Based on compositions and properties, this standard covers the types of laminated pressboard shown in Table 1. The designation of types is the same as that given in IEC 60641-1; in addition, “L” is shown for “laminated” (for example LB0.1). To the description

40、of the types some examples of known applications are added without implying any restriction on other possible applications.60763-1 IEC:2010 5 Table 1 Classification Type Subdivisions Example of application LB0 Pressboard of particularly high chemical purity LB0.1 100 % sulphate wood pulp LB0.2 100 %

41、 cotton LB0.3 Mixture of sulphate wood pulp and cotton Electrical equipment where particularly high chemical purity is required LB2 Pressboard characterized by high chemical purity LB2.1 100 % sulphate wood pulp LB2.2 100 % cotton LB2.3 Mixture of sulphate wood pulp and cotton LB2.4 Mixture of cotto

42、n and jute hemp Transformers LB3 Pre-compressed pressboard, a very hard and rigid board characterized by high chemical purity and mechanical strength. Its surface bears a cloth mark LB3.1 100 % sulphate wood pulp LB3.2 100 % cotton LB3.3 Mixture of sulphate wood pulp and cotton LB3.4 Mixture of cott

43、on and jute hemp Transformers LB4 Pressboard characterized by high chemical purity and high oil absorption and capable of being shaped LB4.1 100 % sulphate wood pulp LB4.2 100 % cotton LB4.3 Mixture of sulphate wood pulp and cotton LB4.4 Mixture of cotton and jute hemp Transformers and oil-immersed

44、equipment LB5 Mouldable press board of high chemical purity and high oil absorption and capable of being shaped LB5.1 100 % sulphate wood pulp LB5.2 100 % cotton LB5.3 Mixture of sulphate wood pulp and cotton LP5.4 Mixture of cotton and jute hemp Transformers and oil-immersed equipment LB6 Pressboar

45、d of low porosity for dry type application LB6.1 100 % sulphate wood pulp LB6.2 100 % cotton LB6.3 Mixture of sulphate wood pulp and cotton LB6.4 Mixture of cotton and jute hemp Motors and general electrical equipment 5 General requirements 5.1 Composition The individual sheets from which the lamina

46、ted board is built up shall conform to all the requirements specified in IEC 60641-1 for the corresponding type of pressboard, except that they need not comply with the requirements for thickness. The laminated board shall be made by laying such sheets unidirectionally and bonding them with a suitab

47、le adhesive. 5.2 Machinability The board shall be capable of being machined with tools appropriate to the material as recommended by the manufacturer. 6 Dimensions The preferred nominal thickness (in millimetres) of the laminated pressboard shall be one of the following: 10 12 15 20 25 30 40 50 Othe

48、r thicknesses are possible. The tolerances on thickness are to be found in Part 3 of this series. 6 60763-1 IEC:2010 7 Conditions of supply The laminated pressboard shall be placed in a packing which ensures adequate protection during transport, handling and storage. A consignment of laminated press

49、board shall be legibly and indelibly marked with the following information: a) manufacturers name or trade mark, if any; b) type of laminated pressboard as given in Table 1; c) nominal thickness; d) sheet size; e) weight (net/gross). _ 8 60763-1 CEI:2010 COMMISSION LECTROTECHNIQUE INTERNATIONALE _ CARTONS COMPRIMS ET CONTRECOLLS USAGES LECTRIQUES Partie 1: Dfiniti