IEC 60227-1-2007 Polyvinyl chloride insulated cables of rated voltages up to and including 450 750 V - Part 1 General requirements《额定电压450 750V及以下的聚氯乙烯绝缘电缆 第1部分 一般要求 》.pdf

《IEC 60227-1-2007 Polyvinyl chloride insulated cables of rated voltages up to and including 450 750 V - Part 1 General requirements《额定电压450 750V及以下的聚氯乙烯绝缘电缆 第1部分 一般要求 》.pdf》由会员分享，可在线阅读，更多相关《IEC 60227-1-2007 Polyvinyl chloride insulated cables of rated voltages up to and including 450 750 V - Part 1 General requirements《额定电压450 750V及以下的聚氯乙烯绝缘电缆 第1部分 一般要求 》.pdf（46页珍藏版）》请在麦多课文档分享上搜索。

1、 IEC 60227-1Edition 3.0 2007-10INTERNATIONAL STANDARD NORME INTERNATIONALEPolyvinyl chloride insulated cables of rated voltages up to and including 450/750 V Part 1: General requirements Conducteurs et cbles isols au polychlorure de vinyle, de tension nominale au plus gale 450/750 V Partie 1: Exigen

2、ces gnrales IEC60227-1:2007 THIS PUBLICATION IS COPYRIGHT PROTECTED Copyright 2007 IEC, Geneva, Switzerland All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and mic

3、rofilm, without permission in writing from either IEC or IECs member National Committee in the country of the requester. If you have any questions about IEC copyright or have an enquiry about obtaining additional rights to this publication, please contact the address below or your local IEC member N

4、ational Committee for further information. Droits de reproduction rservs. Sauf indication contraire, aucune partie de cette publication ne peut tre reproduite ni utilise sous quelque forme que ce soit et par aucun procd, lectronique ou mcanique, y compris la photocopie et les microfilms, sans laccor

5、d crit de la CEI ou du Comit national de la CEI du pays du demandeur. Si vous avez des questions sur le copyright de la CEI ou si vous dsirez obtenir des droits supplmentaires sur cette publication, utilisez les coordonnes ci-aprs ou contactez le Comit national de la CEI de votre pays de rsidence. I

6、EC Central Office 3, rue de Varemb CH-1211 Geneva 20 Switzerland Email: inmailiec.ch Web: www.iec.ch About the IEC The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes International Standards for all electrical, electronic and related tec

7、hnologies. About IEC publications The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the latest edition, a corrigenda or an amendment might have been published. Catalogue of IEC publications: www.iec.ch/searchpub The IEC on-line Catalog

8、ue enables you to search by a variety of criteria (reference number, text, technical committee,). It also gives information on projects, withdrawn and replaced publications. IEC Just Published: www.iec.ch/online_news/justpub Stay up to date on all new IEC publications. Just Published details twice a

9、 month all new publications released. Available on-line and also by email. Electropedia: www.electropedia.org The worlds leading online dictionary of electronic and electrical terms containing more than 20 000 terms and definitions in English and French, with equivalent terms in additional languages

10、. Also known as the International Electrotechnical Vocabulary online. Customer Service Centre: www.iec.ch/webstore/custserv If you wish to give us your feedback on this publication or need further assistance, please visit the Customer Service Centre FAQ or contact us: Email: csciec.ch Tel.: +41 22 9

11、19 02 11 Fax: +41 22 919 03 00 A propos de la CEI La Commission Electrotechnique Internationale (CEI) est la premire organisation mondiale qui labore et publie des normes internationales pour tout ce qui a trait llectricit, llectronique et aux technologies apparentes. A propos des publications CEI L

12、e contenu technique des publications de la CEI est constamment revu. Veuillez vous assurer que vous possdez ldition la plus rcente, un corrigendum ou amendement peut avoir t publi. Catalogue des publications de la CEI: www.iec.ch/searchpub/cur_fut-f.htm Le Catalogue en-ligne de la CEI vous permet de

13、ffectuer des recherches en utilisant diffrents critres (numro de rfrence, texte, comit dtudes,). Il donne aussi des informations sur les projets et les publications retires ou remplaces. Just Published CEI: www.iec.ch/online_news/justpub Restez inform sur les nouvelles publications de la CEI. Just P

14、ublished dtaille deux fois par mois les nouvelles publications parues. Disponible en-ligne et aussi par email. Electropedia: www.electropedia.org Le premier dictionnaire en ligne au monde de termes lectroniques et lectriques. Il contient plus de 20 000 termes et dfinitions en anglais et en franais,

15、ainsi que les termes quivalents dans les langues additionnelles. Egalement appel Vocabulaire Electrotechnique International en ligne. Service Clients: www.iec.ch/webstore/custserv/custserv_entry-f.htm Si vous dsirez nous donner des commentaires sur cette publication ou si vous avez des questions, vi

16、sitez le FAQ du Service clients ou contactez-nous: Email: csciec.ch Tl.: +41 22 919 02 11 Fax: +41 22 919 03 00 IEC 60227-1Edition 3.0 2007-10INTERNATIONAL STANDARD NORME INTERNATIONALEPolyvinyl chloride insulated cables of rated voltages up to and including 450/750 V Part 1: General requirements Co

17、nducteurs et cbles isols au polychlorure de vinyle, de tension nominale au plus gale 450/750 V Partie 1: Exigences gnrales INTERNATIONAL ELECTROTECHNICAL COMMISSION COMMISSION ELECTROTECHNIQUE INTERNATIONALE SICS 29.060.20 PRICE CODECODE PRIXISBN 2-8318-9339-9 2 60227-1 IEC:2007 CONTENTS FOREWORD.4

18、1 General 6 1.1 Scope6 1.2 Normative references 6 2 Definitions 7 2.1 Definitions relating to insulating and sheathing materials7 2.1.1 Polyvinyl chloride compound (PVC)7 2.1.2 Type of compound .7 2.2 Definitions relating to the tests.7 2.2.1 Type tests (symbol T) 7 2.2.2 Sample tests (symbol S) 7 2

19、.3 Rated voltage 7 3 Marking 8 3.1 Indication of origin and cable identification .8 3.1.1 Continuity of marks 8 3.2 Durability.8 3.3 Legibility8 4 Core identification.9 4.1 Core identification by colours .9 4.1.1 General requirements 9 4.1.2 Colour scheme 9 4.1.3 Colour combination green-and-yellow.

20、9 4.2 Core identification by numbers.9 4.2.1 General requirements 9 4.2.2 Preferred arrangement of marking10 4.2.3 Durability .10 5 General requirements for the construction of cables10 5.1 Conductors10 5.1.1 Material .10 5.1.2 Construction 10 5.1.3 Check on construction .11 5.1.4 Electrical resista

21、nce.11 5.2 Insulation.11 5.2.1 Material .11 5.2.2 Application to the conductor .11 5.2.3 Thickness 11 5.2.4 Mechanical properties before and after ageing .11 5.3 Filler13 5.3.1 Material .13 5.3.2 Application.14 5.4 Extruded inner covering .14 5.4.1 Material .14 5.4.2 Application.14 5.4.3 Thickness 1

22、4 5.5 Sheath.14 5.5.1 Material .14 60227-1 IEC:2007 3 5.5.2 Application.14 5.5.3 Thickness 15 5.5.4 Mechanical properties before and after ageing .15 5.6 Tests on completed cables 17 5.6.1 Electrical properties .17 5.6.2 Overall dimensions 18 5.6.3 Mechanical strength of flexible cables 19 5.6.4 Fla

23、me retardance.19 6 Guide to use of the cables 19 Annex A (normative) Code designation 20 Table 1 Requirements for the non-electrical tests for polyvinyl chloride (PVC) insulation 12 Table 2 Requirements for the non-electrical test for polyvinyl chloride (PVC) sheaths16 Table 3 Requirements for elect

24、rical tests for PVC insulated cables .18 4 60227-1 IEC:2007 INTERNATIONAL ELECTROTECHNICAL COMMISSION POLYVINYL CHLORIDE INSULATED CABLES OF RATED VOLTAGES UP TO AND INCLUDING 450/750 V Part 1: General requirements FOREWORD 1) The International Electrotechnical Commission (IEC) is a worldwide organi

25、zation for standardization comprising all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and in addition to other activities, I

26、EC publishes International Standards, Technical Specifications, Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt wi

27、th may participate in this preparatory work. International, governmental and non-governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for Standardization (ISO) in accordance with conditions determined by a

28、greement between the two organizations. 2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international consensus of opinion on the relevant subjects since each technical committee has representation from all interested IEC National Committees. 3) I

29、EC Publications have the form of recommendations for international use and are accepted by IEC National Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC Publications is accurate, IEC cannot be held responsible for the way in which they are u

30、sed or for any misinterpretation by any end user. 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications transparently to the maximum extent possible in their national and regional publications. Any divergence between any IEC Publication and the

31、corresponding national or regional publication shall be clearly indicated in the latter. 5) IEC provides no marking procedure to indicate its approval and cannot be rendered responsible for any equipment declared to be in conformity with an IEC Publication. 6) All users should ensure that they have

32、the latest edition of this publication. 7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and members of its technical committees and IEC National Committees for any personal injury, property damage or other damage of any nature whatsoev

33、er, whether direct or indirect, or for costs (including legal fees) and expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC Publications. 8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publicatio

34、ns is indispensable for the correct application of this publication. 9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent rights. IEC shall not be held responsible for identifying any or all such patent rights. International Standard

35、 IEC 60227-1 has been prepared by IEC technical committee 20: Electric cables. This third edition of IEC 60227-1 cancels and replaces the second edition, published in 1993, amendment 1 (1995) and amendment 2 (1997) The document 20/903/FDIS, circulated to the National Committees as amendment 3, led t

36、o the publication of this new edition. 60227-1 IEC:2007 5 The text of this standard is based on the second edition, its amendments 1 and 2, and the following documents: FDIS Report on voting 20/903/FDIS 20/910/RVD Full information on the voting for the approval of this standard can be found in the r

37、eport on voting indicated in the above table. This publication has been drafted in accordance with the ISO/IEC Directives, Part 2. The committee has decided that the contents of this publication will remain unchanged until the maintenance result date indicated on the IEC web site under “http:/websto

38、re.iec.ch“ in the data related to the specific publication. At this date, the publication will be reconfirmed, withdrawn, replaced by a revised edition, or amended. 6 60227-1 IEC:2007 POLYVINYL CHLORIDE INSULATED CABLES OF RATED VOLTAGES UP TO AND INCLUDING 450/750 V Part 1: General requirements 1 G

39、eneral 1.1 Scope This part of International Standard IEC 60227 applies to rigid and flexible cables with insulation, and sheath if any, based on polyvinyl chloride, of rated voltages Uo/U up to and including 450/750 V used in power installations of nominal voltage not exceeding 450/750 V a.c. NOTE F

40、or some types of flexible cables the term cord is used. The particular types of cables are specified in IEC 60227-3, IEC 60227-4, etc. The code designations of these types of cables are given in Annex A. The test methods specified in Parts 1, 3, 4, etc. are given in IEC 60227-2, IEC 60332-1-2 and in

41、 the relevant parts of IEC 60811. 1.2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments)

42、 applies. IEC 60173, Colours of the cores of flexible cables and cords IEC 60227-2, Polyvinyl chloride insulated cables of rated voltage up to and including 450/750 V Part 2: Test methods IEC 60227-3, Polyvinyl chloride insulated cables of rated voltage up to and including 450/750 V Part 3: Non-shea

43、thed cables for fixed wiring IEC 60227-4, Polyvinyl chloride insulated cables of rated voltage up to and including 450/750 V Part 4: Sheathed cables for fixed wiring IEC 60227-5, Polyvinyl chloride insulated cables of rated voltages up to and including 450/750 V Part 5: Flexible cables (cords) IEC 6

44、0228, Conductors of insulated cables IEC 60332-1-2, Tests on electric and optical fibre cables under fire conditions Part 1-2: Test for vertical flame propagation for a single insulated wire or cable Procedure for 1 kW pre-mixed flame IEC 60811-1-1, Common test methods for insulating and sheathing m

45、aterials of electric cables and optical cables Part 1: Methods for general application Measuring of thickness and overall dimensions Tests for determining the mechanical properties 60227-1 IEC:2007 7 IEC 60811-1-2, Common test methods for insulating and sheathing materials of electric cables Part 1:

46、 Methods for general application Section Two: Thermal ageing methods IEC 60811-1-4, Common test methods for insulating and sheathing materials of electric cables Part 1: Methods for general application Section Four: Tests at low temperature IEC 60811-3-1, Common test methods for insulating and sheat

47、hing materials of electric cables Part 3: Methods specific to PVC compounds Section One: Pressure test at high temperature Tests for resistance to cracking IEC 60811-3-2, Common test methods for insulating and sheathing materials of electric cables Part 3: Methods specific to PVC compounds Section T

48、wo: Loss of mass test Thermal stability tests IEC 62440, Electric cables Guide to use for cables with a rated voltage not exceeding 450/750V12 Definitions For the purpose of this standard the following definitions shall apply. 2.1 Definitions relating to insulating and sheathing materials 2.1.1 Poly

49、vinyl chloride compound (PVC) Combination of materials suitably selected, proportioned and treated, of which the characteristic constituent is the plastomer polyvinyl chloride or one of its copolymers. The same term also designates compounds containing both polyvinyl chloride and certain of its polymers. 2.1.2 Type of compound The category in which a compound is placed according