IEC 60060-3-2006 High voltage test techniques - Part 3 Definitions and requirements for on-site testing《高压试验技术.第3部分 现场试验的定义和要求》.pdf

《IEC 60060-3-2006 High voltage test techniques - Part 3 Definitions and requirements for on-site testing《高压试验技术.第3部分 现场试验的定义和要求》.pdf》由会员分享，可在线阅读，更多相关《IEC 60060-3-2006 High voltage test techniques - Part 3 Definitions and requirements for on-site testing《高压试验技术.第3部分 现场试验的定义和要求》.pdf（40页珍藏版）》请在麦多课文档分享上搜索。

1、 INTERNATIONAL STANDARD IEC 60060-3First edition 2006-02High-voltage test techniques Part 3: Definitions and requirements for on-site testing Reference number IEC 60060-3:2006(E) Publication numbering As from 1 January 1997 all IEC publications are issued with a designation in the 60000 series. For

2、example, IEC 34-1 is now referred to as IEC 60034-1. Consolidated editions The IEC is now publishing consolidated versions of its publications. For example, edition numbers 1.0, 1.1 and 1.2 refer, respectively, to the base publication, the base publication incorporating amendment 1 and the base publ

3、ication incorporating amendments 1 and 2. Further information on IEC publications The technical content of IEC publications is kept under constant review by the IEC, thus ensuring that the content reflects current technology. Information relating to this publication, including its validity, is avail

4、able in the IEC Catalogue of publications (see below) in addition to new editions, amendments and corrigenda. Information on the subjects under consideration and work in progress undertaken by the technical committee which has prepared this publication, as well as the list of publications issued, is

5、 also available from the following: IEC Web Site (www.iec.ch) Catalogue of IEC publications The on-line catalogue on the IEC web site (www.iec.ch/searchpub) enables you to search by a variety of criteria including text searches, technical committees and date of publication. On-line information is al

6、so available on recently issued publications, withdrawn and replaced publications, as well as corrigenda. IEC Just Published This summary of recently issued publications (www.iec.ch/online_news/ justpub) is also available by email. Please contact the Customer Service Centre (see below) for further i

7、nformation. Customer Service Centre If you have any questions regarding this publication or need further assistance, please contact the Customer Service Centre: Email: custserviec.ch Tel: +41 22 919 02 11 Fax: +41 22 919 03 00 INTERNATIONAL STANDARD IEC 60060-3First edition 2006-02High-voltage test

8、techniques Part 3: Definitions and requirements for on-site testing IEC 2006 Copyright - all rights reserved No part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from the p

9、ublisher. International Electrotechnical Commission, 3, rue de Varemb, PO Box 131, CH-1211 Geneva 20, Switzerland Telephone: +41 22 919 02 11 Telefax: +41 22 919 03 00 E-mail: inmailiec.ch Web: www.iec.ch V For price, see current catalogue PRICE CODE Commission Electrotechnique Internationale Intern

10、ational Electrotechnical Commission 2 60060-3 IEC:2006(E) CONTENTS FOREWORD.4 INTRODUCTION.6 1 Scope.7 2 Normative references .7 3 Terms and definitions .7 4 Common tests and checks on a measuring system.12 4.1 Acceptance test.12 4.2 Performance test.12 4.3 Performance check12 4.4 Record of performa

11、nce13 5 Tests with direct voltage.13 5.1 General .13 5.2 Definitions for direct voltage tests13 5.3 Test voltage 14 5.4 Measurement of the test voltage14 5.5 Tests and checks on measuring systems.15 5.6 Withstand voltage test procedure 15 6 Tests with alternating voltage .15 6.1 General .15 6.2 Defi

12、nitions for alternating voltage tests15 6.3 Test voltage 16 6.4 Measurement of the test voltage17 6.5 Tests and checks on measuring systems.18 6.6 Withstand voltage test procedure 18 7 Tests with lightning impulse voltage .18 7.1 General .18 7.2 Definitions for lightning impulse voltage tests 18 7.3

13、 Test voltage 21 7.4 Measurement of the test voltage and determination of the impulse voltage shape22 7.5 Tests and checks on measuring systems.22 7.6 Withstand voltage test procedures.23 8 Tests with switching impulse voltage 23 8.1 General .23 8.2 Definitions for switching impulse voltage tests.23

14、 8.3 Test voltage 26 8.4 Measurement of the test voltage and determination of the impulse shape26 8.5 Tests and checks on measuring systems.27 8.6 Withstand voltage test procedures.27 9 Tests with very low frequency voltages.28 9.1 General .28 9.2 Definitions for very low frequency voltage tests .28

15、 9.3 Test voltage 29 9.4 Measurement of the test voltage29 9.5 Tests and checks on measuring systems.30 9.6 Test procedure30 60060-3 IEC:2006(E) 3 10 Tests with damped alternating voltages 30 10.1 General .30 10.2 Definitions for damped alternating voltage tests 30 10.3 Test voltage 31 10.4 Measurem

16、ent of the test voltage32 10.5 Tests and checks on measuring systems.32 10.6 Test procedure33 Figure 1 Aperiodic lightning impulse 19 Figure 2 Oscillating lightning impulse.20 Figure 3 Aperiodic switching impulse .24 Figure 4 Oscillating switching impulse25 Figure 5 Damped alternating voltage (f r=

17、1 kHz, D f= 0,2) 31 4 60060-3 IEC:2006(E) INTERNATIONAL ELECTROECHNICAL COMMISSION _ HIGH-VOLTAGE TEST TECHNIQUES Part 3: Definitions and requirements for on-site testing FOREWORD 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising all na

18、tional electrotechnical committees (IEC National Committees). The object of IEC is to promote international co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and in addition to other activities, IEC publishes International Standards, Techni

19、cal Specifications, Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with may participate in this preparatory work.

20、 International, governmental and non- governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for Standardization (ISO) in accordance with conditions determined by agreement between the two organizations. 2)

21、The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international consensus of opinion on the relevant subjects since each technical committee has representation from all interested IEC National Committees. 3) IEC Publications have the form of recommenda

22、tions for international use and are accepted by IEC National Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any misinterpretation by any end

23、 user. 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications transparently to the maximum extent possible in their national and regional publications. Any divergence between any IEC Publication and the corresponding national or regional publicat

24、ion shall be clearly indicated in the latter. 5) IEC provides no marking procedure to indicate its approval and cannot be rendered responsible for any equipment declared to be in conformity with an IEC Publication. 6) All users should ensure that they have the latest edition of this publication. 7)

25、No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and members of its technical committees and IEC National Committees for any personal injury, property damage or other damage of any nature whatsoever, whether direct or indirect, or for cost

26、s (including legal fees) and expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC Publications. 8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is indispensable for the correct applica

27、tion of this publication. 9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent rights. IEC shall not be held responsible for identifying any or all such patent rights. International Standard IEC 60060-3 has been prepared by IEC techn

28、ical committee 42: High- voltage testing techniques. The text of this standard is based on the following documents: FDIS Report on voting 42/203/FDIS 42/204/RVD Full information on the voting for the approval of this standard can be found in the report on voting indicated in the above table. This pu

29、blication has been drafted in accordance with the ISO/IEC Directives, Part 2. Terms used throughout this standard which have been defined in Clause 3 are written in bold type. 60060-3 IEC:2006(E) 5 IEC 60060 consists of the following parts, under the general title High-voltage test techniques: Part

30、1: General definitions and test requirements Part 2: Measuring systems Part 3: Definitions and requirements for on-site testing The committee has decided that the contents of this publication will remain unchanged until the maintenance result date indicated on the IEC web site under “http:/webstore.

31、iec.ch“ in the data related to the specific publication. At this date, the publication will be reconfirmed; withdrawn; replaced by a revised edition, or amended. A bilingual version of this publication may be issued at a later date. 6 60060-3 IEC:2006(E) INTRODUCTION The requirements specified in IE

32、C 60060-1 and IEC 60060-2 cannot always be achieved during on-site tests, due to a variety of external factors not present in factory and laboratory tests such as external electric and magnetic fields, weather conditions, etc. On-site high-voltage tests are required: as withstand tests as part of a

33、commissioning procedure on equipment to demonstrate that transport from manufacturer to site, and the erection on-site complies with manufacturers specification; as withstand tests after on-site repair, to demonstrate that the equipment has been successfully repaired, and is in a suitable condition

34、to return to service; for diagnostic purposes, e.g. PD measurement, to demonstrate if the insulation is still free from dangerous defects, and as an indication of life expectation. 60060-3 IEC:2006(E) 7 HIGH-VOLTAGE TEST TECHNIQUES Part 3: Definitions and requirements for on-site testing 1 Scope Thi

35、s part of IEC 60060 is applicable to the following on-site test voltages and in service stresses, which are in relation to IEC 60060-1: direct voltage; alternating voltage; lightning impulse voltage of aperiodic or oscillating shape; switching impulse voltage of aperiodic or oscillating shape. For s

36、pecial tests the following voltages are used: very low frequency voltage; damped alternating voltage. This standard is applicable to equipment with a highest voltage U mgreater than 1 kV. The selection of on-site test voltages, test procedures and test voltage levels for apparatus, equipment or inst

37、allations is under the responsibility of the relevant technical committee. For special applications, on-site test voltages different from those described in this standard may be specified by the relevant technical committee. NOTE 1 The different voltage waveforms listed above do not necessarily prov

38、ide equal stress on the test object. NOTE 2 The selection of the test voltage levels should take the larger tolerances and measuring uncertainties into account. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, onl

39、y the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. IEC 60060-1:1989, High-voltage test techniques Part 1: General definitions and test requirements IEC 60060-2:1994, High-voltage test techniques Part 2: Measuring sys

40、tems IEC 60071-1:1993, Insulation co-ordination Part 1: Definitions, principles and rules 3 Terms and definitions For the purposes of this document, the following terms and definitions apply. For all other definitions relating to testing procedures, see IEC 60060-1, and for those relating to measuri

41、ng systems, see IEC 60060-2. Definitions of parameters are given in the relevant clauses of this standard. 3.1 on-site test test at the place of use of the apparatus, equipment or installation that is to be tested, and with the test object as far as possible in its service condition 8 60060-3 IEC:20

42、06(E) 3.2 impulse voltage intentionally applied aperiodic or oscillating transient voltage, which usually rises rapidly to a peak value and then its enveloping curve falls more slowly to zero (IEC 60060-1:1989, Term 3, modified) 3.3 lightning and switching impulse voltages a distinction is made betw

43、een lightning and switching impulse voltages on the basis of duration of the front. Impulses with front duration up to 20 s are defined as lightning impulse voltages and those with longer fronts are defined as switching impulse voltages Generally, switching impulse voltages are also characterized by

44、 total durations considerably longer than those of lightning impulse voltages. (IEC 60060-1:1989, Term 3.1) 3.4 characteristics of the test voltage those characteristics specified in this standard for designating the different types of voltage excursion that define the test voltage (IEC 60060-1:1989

45、, Term 4.2) 3.5 prospective characteristics of a test voltage the characteristics which would have been obtained if no disruptive discharge had occurred. When a prospective characteristic is used, this shall always be stated (IEC 60060-1:1989, Term 4.2.1) 3.6 actual characteristics of a test voltage

46、 characteristics that occur during the test at the terminals of the test object (IEC 60060-1:1989, Term 4.2.2) 3.7 value of the test voltage as defined in the relevant clauses of the present standard (IEC 60060-1:1989, Term 4.2.3) 3.8 classification of insulation in test objects insulation systems o

47、f apparatus and high-voltage structures must basically be classified into self-restoring and non-self-restoring insulation and may consist of external and/or internal insulation (IEC 60060-1:1989, Term 5) 3.8.1 external insulation distances in atmospheric air, and the surfaces in contact with atmosp

48、heric air of solid insulation of the equipment which are subject to dielectric stresses and to the effects of atmospheric and other external conditions such as pollution, humidity, vermin, etc. (IEC 60071-1:1993, Term 3.2) 60060-3 IEC:2006(E) 9 3.8.2 internal insulation internal solid, liquid or gas

49、eous insulation, which are protected from the effects of atmospheric and other external conditions (IEC 60071-1:1993, Term 3.3) 3.8.3 self-restoring insulation insulation that completely recovers its insulating properties after a certain time interval following a disruptive discharge caused by the application of a test voltage (IEC 60071-1:1993, Term 3.4, modified) 3.8.4 non-self-restoring insulation insulation that l