UL 8754-2013 UL Standard for Safety Holders Bases and Connectors for Solid-State (LED) Light Engines and Arrays (First Edition Reprint with revisions through and including August 3.pdf

《UL 8754-2013 UL Standard for Safety Holders Bases and Connectors for Solid-State (LED) Light Engines and Arrays (First Edition Reprint with revisions through and including August 3.pdf》由会员分享，可在线阅读，更多相关《UL 8754-2013 UL Standard for Safety Holders Bases and Connectors for Solid-State (LED) Light Engines and Arrays (First Edition Reprint with revisions through and including August 3.pdf（44页珍藏版）》请在麦多课文档分享上搜索。

1、UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL UL 8754 Holders, Bases, and Connectors for Solid-State (LED) Light Engines and ArraysUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM ULUL

2、 COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL UL Standard for Safety for Holders, Bases, and Connectors for Solid-State (LED) Light Engines and Arrays, UL 8754 First Edition, Dated July 31, 2013 Summary of Topics The following changes in req

3、uirements to the Joint UL/ULC Standard for Holders, Bases, and Connectors for Solid-State (LED) Light Engines and Arrays, UL 8754/ULC-S8754, are being issued for the United States and Canada: 1. Revise Relative Thermal Index (RTI) requirements for polymeric materials used in Limited Application Devi

4、ces (LAD) 2. Add exception to loading test for solid-state assembly holders 3. Clarify requirements for lead pull tests for factory assembled solid-state assembly holders 4. Clarify product marking allowances for lampholders Text that has been changed in any manner or impacted by ULs electronic publ

5、ishing system is marked with a vertical line in the margin. Changes in requirements are marked with a vertical line in the margin and are followed by an effective date note indicating the date of publication or the date on which the changed requirement becomes effective. The new and revised requirem

6、ents are substantially in accordance with Proposal(s) on this subject dated September 19, 2014. All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form by any means, electronic, mechanical photocopying, recording, or otherwise with

7、out prior permission of UL. UL provides this Standard as is without warranty of any kind, either expressed or implied, including but not limited to, the implied warranties of merchantability or tness for any purpose. In no event will UL be liable for any special, incidental, consequential, indirect

8、or similar damages, including loss of prots, lost savings, loss of data, or any other damages arising out of the use of or the inability to use this Standard, even if UL or an authorized UL representative has been advised of the possibility of such damage. In no event shall ULs liability for any dam

9、age ever exceed the price paid for this Standard, regardless of the form of the claim. Users of the electronic versions of ULs Standards for Safety agree to defend, indemnify, and hold UL harmless from and against any loss, expense, liability, damage, claim, or judgment (including reasonable attorne

10、ys fees) resulting from any error or deviation introduced while purchaser is storing an electronic Standard on the purchasers computer system. The requirements in this Standard are now in effect, except for those paragraphs, sections, tables, gures, and/or other elements of the Standard having futur

11、e effective dates as indicated in the preface. The prior text for requirements that have been revised and that have a future effective date are located after the Standard, and are preceded by a SUPERSEDED REQUIREMENTS notice. DECEMBER 18, 2014 UL 8754 tr1UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FU

12、RTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL DECEMBER 18, 2014 UL 8754 tr2 No Text on This PageUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL ULC Standards CAN/ULC-S8754 First Edition Underwriters Laboratories Inc. ANSI/UL

13、8754 First Edition Holders, Bases, and Connectors for Solid-State (LED) Light Engines and Arrays July 31, 2013 (Title Page Reprinted: December 18, 2014) ANSI/UL 8754-2014 Approved byUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL Commitment

14、for Amendments This Standard is issued jointly by Underwriters Laboratories Inc. (UL) and ULC Standards. Amendments to this Standard will be made only after processing according to the Standards writing procedures by UL and ULC Standards. UL and ULC Standards are separate and independent entities an

15、d each is solely responsible for its operations and business activities. The UL trade names and trademarks depicted in this document are the sole property of Underwriters Laboratories Inc. The ULC Standards trade names and trademarks depicted in this document are the sole property of ULC Standards.

16、ISSN 0317-526X Copyright 2014 ULC Standards All rights reserved. No part of this publication may be reproduced in any form, in an electronic retrieval system or otherwise, whatsoever without the prior permission of the publisher. In Canada, written comments are to be sent to ULC Standards, 400 171 N

17、epean Street, Ottawa, Ontario KP2 0B4. Proposals should be submitted on a Standards Revision Request Form available from ULC Standards. Copyright 2014 Underwriters Laboratories Inc. ULs Standards for Safety are copyrighted by UL. Neither a printed nor electronic copy of a Standard should be altered

18、in any way. All of ULs Standards and all copyrights, ownerships, and rights regarding those Standards shall remain the sole and exclusive property of UL. This ANSI/UL Standard for Safety consists of the First Edition including revisions through December 18, 2014. The most recent designation of ANSI/

19、UL 8754 as an American National Standard (ANSI) occurred on December 18, 2014. ANSI approval for a standard does not include the Cover Page, Transmittal Pages, Title Page (front and back), an informative Annex, or the Preface. Comments or proposals for revisions on any part of the Standard may be su

20、bmitted to UL at any time. Proposals should be submitted via a Proposal Request in ULs On-Line Collaborative Standards Development System (CSDS) at http:/. To purchase UL Standards, visit Comm 2000 at http:/m- or call toll-free 1-888-853-3503.UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPROD

21、UCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL CONTENTS Preface .5 1 Scope .6 2 Denitions 6 3 General 8 3.1 Reference Publications .8 3.2 Components .9 3.3 Units of Measurement .9 4 Construction 9 4.1 Enclosures 9 4.2 Insulating materials 10 4.3 Sealing compound .11 4.4 Mounting .11 4.5 Accessibi

22、lity of live parts .11 4.6 Corrosion protection .12 4.7 Current-carrying parts 12 4.8 Supply connections 13 4.9 Creepage distances and clearances .15 4.10 Current-interrupting devices .17 4.11 Lamplocks .17 4.12 Lampholder conguration .17 4.13 Grounding .18 4.14 Mass .18 4.15 Environmental considera

23、tions 19 4.16 Dened-t system 19 5 Tests .19 5.1 General 19 5.2 Millivolt drop test 20 5.3 Mechanical cycling test .20 5.4 Abnormal overload test .20 5.5 Temperature rise test 21 5.6 Loading 21 5.7 Grounding contact test .22 5.8 Deection test 22 5.9 Humidity conditioning (followed by dielectric volta

24、ge withstand) .22 5.10 Switching mechanism test .23 5.11 Security of leads test .24 5.12 Dimensional conformity test .24 6 Ratings .24 7 Markings 24 7.1 General 24 7.2 Permanence 26 7.3 Details .26 8 Test Apparatus 26 8.1 Lamp base shorting xture .26 8.2 Lamp base overload xture .27 JULY 31, 2013 CA

25、N/ULC-S8754 ANSI/UL 8754 3UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL ANNEX A (NORMATIVE) Reference Standards ANNEX B (CAN) (normative) Markings French Translation JULY 31, 2013 CAN/ULC-S8754 ANSI/UL 8754 4UL COPYRIGHTED MATERIAL NOT AUT

26、HORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL Preface This is the common UL and ULC Standard for Holders, Bases, and Connectors for Solid-State (LED) Light Engines and Arrays. It is the First edition of both CAN/ULC-S8754 and ANSI/UL 8754. This Joint Standard was prepar

27、ed by Underwriters Laboratories Inc., ULC Standards, and the Technical Committee on Field-Replaceable LED Light Engines. The standard was formally approved by the UL/ULC Technical Committee on Field-Replaceable LED Light Engines. The efforts and support of the Technical Committee are gratefully ackn

28、owledged. Only metric SI units of measurement are used in this Standard. If a value for measurement is followed by a value in other units in parentheses, the second value may be approximate. The rst stated value is the requirement. In Canada, there are two official languages, English and French. All

29、 safety warnings must be in French and English. Attention is drawn to the possibility that some Canadian authorities may require additional markings and/or installation instructions to be in both official languages. Annex A and Annex B, both identifed as normative, form a mandatory part of this Stan

30、dard. Note: Although the intended primary application of this Standard is stated in its scope, it is important to note that it remains the responsibility of the users of the standard to judge its suitability for their particular purpose. Level of Harmonization This Standard is published as an identi

31、cal standard between UL and ULC Standards. An identical standard is a standard that is the same in technical content except for conicts in Codes and Governmental Regulations. Presentation shall be word for word except for editorial changes. Interpretations The interpretation by the SDO of an identic

32、al or equivalent standard shall be based on the literal text to determine compliance with the standard in accordance with the procedural rules of the SDO. If more than one interpretation of the literal text has been identied, a revision shall be proposed as soon as possible to each of the SDOs to mo

33、re accurately reect the intent. UL Effective Date A UL effective date is established by Underwriters Laboratories Inc. and is not part of the ANSI approved standard. JULY 31, 2013 CAN/ULC-S8754 ANSI/UL 8754 5UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERM

34、ISSION FROM UL 1 Scope 1.1 This standard species the requirements applicable to holders, bases and connectors intended for solid-state (LED) light engines and arrays for installation in lighting equipment, provided that they employ a conguration not typically found on incandescent or uorescent light

35、 sources. 1.2 This standard does not cover lampholders with screw, bayonet or pin-type bases intended to be compatible with incandescent or uorescent lamps. Such lampholders are covered under CSA C22.2 No. 43 / UL 496. 1.3 This standard does not cover wire connectors. Such connectors are covered und

36、er CAN/CSA-C22.2 No. 65 / UL 486A-486B or CSA C22.2 No. 2459 / UL 2459. 2 Denitions 2.1 For the purpose of this standard, the following denitions apply: 2.2 BASE That part of a lampholder that is used for mounting of the device. 2.3 CURRENT-INTERRUPTING DEVICE A component (such as a switch or breake

37、r) intended to stop the ow of current in a lampholder circuit. 2.4 ENCLOSURE That part or parts of a lampholder that: a) Renders inaccessible all or any parts of the equipment that may otherwise present a risk of electric shock, or b) Retards propagation of ame caused by electrical disturbances occu

38、rring within. 2.5 INSULATION, BASIC The insulation necessary to provide basic protection against the risk of electric shock. This insulation may be in the form of vulcanized ber, an inorganic or polymeric material, or an air gap. 2.6 INSULATION, DOUBLE An insulation system comprised of both basic in

39、sulation and supplementary insulation. 2.7 INSULATION, REINFORCED A single insulation system with such mechanical and electrical qualities that it, in itself, provides the same degree of protection against the risk of electric shock as does double insulation. Note: The term “single insulation system

40、” does not necessitate that the insulation must be in one homogeneous piece. The insulation system may comprise two or more layers that cannot be tested as supplementary or basic insulation. 2.8 INSULATION, SUPPLEMENTARY An independent insulation provided in addition to the basic insulation to provi

41、de protection against the risk of electric shock in case of breakdown of the basic insulation. 2.9 LAMP BASE The part of a lamp that engages the lampholder and makes contact with the electrical circuits of the lampholder. 2.10 LAMP CONNECTOR A type of lampholder that provides electrical connection t

42、o a lamp but does not provide mechanical support; sometimes known as a lamp-supported lampholder. JULY 31, 2013 CAN/ULC-S8754 ANSI/UL 8754 6UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL 2.11 LAMPHOLDER A wiring device intended for making c

43、onnection to the electrical circuits of a lamp and, in some cases, providing support. 2.12 LAMPLOCK A feature intended to keep a lamp from being removed except by a person having a key or special tool. 2.13 LED ARRAY (LED MODULE) An assembly of one or more LED packages or dies on a printed circuit b

44、oard or substrate, possibly with optical elements and additional thermal, mechanical, and electrical interfaces that are intended to connect to the load side of an LED driver. 2.14 LED LIGHT ENGINE (LIGHT ENGINE) An integrated assembly comprised of an LED array (LED module), LED driver, and other op

45、tical, thermal, mechanical and electrical components. The device is intended to connect directly to the branch circuit through a custom or industry-standard lamp base. This lamp base shall be of a type not typically found on incandescent or uorescent light sources. a a With permission from ANSI/IES

46、RP-16, Nomenclature and Denitions for Illuminating Engineering, by the Illuminating Engineering Society of North America. 2.15 LIMITED APPLICATION DEVICE (LAD) Lampholders that: a) Are only suitable for connection to low voltage, low energy circuits supplied from a Class 2 or LVLE source; or b) Are

47、solely used to provide mechanical support to the light engine and its components, and provide no direct support of live parts. Note: The following clauses contain requirements, exceptions or notes applicable to limited application devices: 4.2.3, 4.2.6, 4.5.2, 4.8.5.2, 4.9.10, 4.12.3, 5.1.1, 5.3.1,

48、5.3.3, 6.2, and 7.3.3. 2.16 LIVE PART A metal or other conductive part that, during intended use, has an electrical potential difference with respect to earth ground or any other conductive part. By denition, the grounded (or neutral) mains supply conductor is considered to be a live part. 2.17 LOCA

49、TION, DAMP An interior or exterior location that is normally or periodically subject to condensation of moisture, including partially protected locations. The interior of a luminaire or sign intended for wet locations is considered a damp location. Note: Examples of damp locations include partially protected locations under canopies, marquees, roofed open porches, and interior locations subject to moderate degrees of moisture, su