UL 60730-2-22 (ND)-2017 National Differences For UL 60730-2-22 Automatic Electrical Controls C Part 2-22 Particular Requirements for Thermal Motor Protectors (First Edition).pdf

《UL 60730-2-22 (ND)-2017 National Differences For UL 60730-2-22 Automatic Electrical Controls C Part 2-22 Particular Requirements for Thermal Motor Protectors (First Edition).pdf》由会员分享，可在线阅读，更多相关《UL 60730-2-22 (ND)-2017 National Differences For UL 60730-2-22 Automatic Electrical Controls C Part 2-22 Particular Requirements for Thermal Motor Protectors (First Edition).pdf（8页珍藏版）》请在麦多课文档分享上搜索。

1、UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION ORDISTRIBUTION WITHOUT PERMISSION FROM ULNational Differences ForUL 60730-2-22Automatic Electrical Controls Part 2-22: Particular Requirements for Thermal Motor ProtectorsUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION O

2、RDISTRIBUTION WITHOUT PERMISSION FROM ULNational Differences ForUL 60730-2-22Automatic Electrical Controls Part 2-22: Particular Requirements for Thermal Motor ProtectorsFirst EditionEdition Date: APRIL 7, 2017This first edition of ANSI/UL 60730-2-22 adopts the first edition of IEC 60730-2-22 with n

3、ationaldifferences.This document provides a single listing of the National Differences included in the UL adoption ofthe corresponding IEC standard.All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, ortransmitted in any form by any means, electronic, me

4、chanical photocopying, recording, or otherwisewithout prior permission of UL.UL provides this standards document as is without warranty of any kind, either expressed or implied,including but not limited to, the implied warranties of merchantability or fitness for any purpose.In no event will UL be l

5、iable for any special, incidental, consequential, indirect or similar damages,including loss of profits, lost savings, loss of data, or any other damages arising out of the use of or theinability to use this standards document, even if UL or an authorized UL representative has been advisedof the pos

6、sibility of such damage. In no event shall ULs liability for any damage ever exceed the pricepaid for this standards document, regardless of the form of the claim.Users of the electronic versions of ULs Standards for Safety agree to defend, indemnify, and hold ULharmless from and against any loss, e

7、xpense, liability, damage, claim, or judgment (including reasonableattorneys fees) resulting from any error or deviation introduced while purchaser is storing an electronicStandard on the purchasers computer system.Copyright 2017 Underwriters Laboratories Inc.APRIL 7, 2017NATIONAL DIFFERENCES FOR UL

8、 60730-2-222UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION ORDISTRIBUTION WITHOUT PERMISSION FROM ULPrefaceThis document provides a single listing of the technical National Differences included in the UL adoptionof the corresponding IEC standard.In its IEC-based standards, UL uses t

9、he notations indicated below to identify national difference type, andthese types are additionally noted in this document. The standard may not use all types of thesedeviations.D1 - These are deviations which are based on basic safety principles and requirements, elimination ofwhich would compromise

10、 safety for U.S. consumers and users of products.D2 - These are deviations based on safety practices. These are deviations for IEC requirements that maybe acceptable, but adopting the IEC requirements would require considerable retesting or redesign on themanufacturers part.DC - These are deviations

11、 based on the component standards and will not be deleted until a particularcomponent standard is harmonized with the IEC component standard.DE - These are deviations based on editorial comments or corrections.DR - These are deviations based on the national regulatory requirements.Each national diff

12、erence contains a description of what the national difference entails. Typically one of thefollowing words is used to explain how the text of the national difference is to be applied to the base IECtext:Addition / Add - An addition entails adding a complete new numbered clause, subclause, table, fig

13、ure,or annex. Addition is not meant to include adding select words to the base IEC text.Deletion / Delete - A deletion entails complete deletion of an entire numbered clause, subclause, table,figure, or annex without any replacement text.Modification / Modify - A modification is an altering of the e

14、xisting base IEC text such as the addition,replacement or deletion of certain words or the replacement of an entire clause, subclause, table, figure,or annex of the base IEC text.APRIL 7, 2017 NATIONAL DIFFERENCES FOR UL 60730-2-22 3UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION ORD

15、ISTRIBUTION WITHOUT PERMISSION FROM ULNational Differences1.1DV DE Modification of 1.1 to by adding the following note after the third paragraph:NOTE Thermal motor protectors that are off-winding (not integrated with the motor winding) to the motor arecovered under the scope of this part 2 and may b

16、e considered incorporated controls with respective to therequirements of this standard. Thermal protectors with integral heating elements (resistors, thermistors and thelike) are considered voltage maintained thermal cutouts and are covered under UL 60730-2-9.1.1.1DV D2 Addition:1.1.1DV.1 This part

17、2 is to be used in conjunction with the latest edition of UL 60730-1 andits amendments.1.1.101DV D2 Addition:1.1.101DV.1 This standard applies to thermal motor protectors designed for household,commercial, or industrial use.2.6.101DV D2 Modification by adding the following notes:NOTE 1 Type 3 action

18、 applies to in-winding, integrated thermal motor protectors.NOTE 2 Type 2 action applies to off-winding, incorporated thermal motor protectors.4.3.2DV D2 Modification of 4.3.2:4.3.2DV.1 The requirements in 4.3.2 are applicable.6.11DV D2 Modification of 6.11 by replacing it with the following:6.11DV.

19、1 This clause of the Part 1 is applicable for controls declared as incorporatedcontrols with endurance values in Table 1DV.Table 1DV D2 Replace Table 1 of the Part 2 with the following table:APRIL 7, 2017NATIONAL DIFFERENCES FOR UL 60730-2-224UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPROD

20、UCTION ORDISTRIBUTION WITHOUT PERMISSION FROM ULTable 1DVInformation Clause orsubclauseMethod1 Manufacturers name or trade mark 7.2.6 C2 UNIQUE TYPE REFERENCEa2.11.1, 2.13.1, 7.2.6 C3 Rated voltage or rated voltage range in volts (V) 2.1.2 D6 Purpose of control 4.3.5, 6.3 X27DV Number of automatic c

21、ycles (A) for each AUTOMATIC ACTION) 6.11DV.1, 17.8 X30 PTI of materials used for insulation 6.13 X31 Method of mounting control 11.6 X31a Method of providing earthing of control 7.4.3, 9 D37DV Minimum and/or maximum rates of change of ACTIVATING QUANTITY, orminimum and/or maximum cycling rates for

22、a SENSING CONTROL4)15, 17 X39DV Type of Action 6.4 D41DV MANUFACTURING DEVIATION and condition of test appropriate todeviation15, 17.14 X42DV DRIFT 15, 16.2.4DV.1 X43 Reset characteristics for cut-out actionb6.4, 11.4 X49 Control POLLUTION degree 6.5.3 X51 Heat and fire resistance category 21 X77 Te

23、mperature for the ball pressure test 21.2.1, 21.2.2,21.2.3 and 21.2.4D101 Limited short-circuit capability in terms of prospective current, voltageand rated current and characteristic of fuse, if declaredc6.101, 17.101 X102 Features of AUTOMATIC ACTIONSd6.4 D103 Maximum pressure for controls located

24、 within the sealed compressorenclosuree18.1.3.101.1 DDV Note 4 of the part 1 applies.aThe UNIQUE TYPE REFERENCE shall be such that, when it is quoted in full, the manufacturer of thecontrol can supply a replacement which will be fully interchangeable with the original electrically,mechanically, dime

25、nsionally and functionally.It may comprise a series type reference with other marking, such as voltage rating or an ambienttemperature marking, which together provide a UNIQUE TYPE REFERENCE.bManufacturers may declare a lower ambient temperature than that specified in 11.4.102.cApplicable in Canada

26、and the USA.dDVThermal motor protectors are classified as Type 3.B.H or 3.B controls.eThe test pressure depends on the intended refrigerant and the location of the protector inside thecompressor (high side or low side). Values can be taken from 22.7 of IEC 60335-2-34:2012.15DV D2 Modification of Cla

27、use 15:15DV.1 The requirements in Clause 15 are applicable to thermal motor protectors that aredeclared to be incorporated with deviation and drift values in Table 1DV.17DV D2 Modification of Clause 17:17DV.1 This clause of Part 1 is applicable to thermal motor protectors only when declaredin Table

28、1DV. All sub-clauses of the Part 1 are applicable except as follows:17.1.3.1DV D2 Addition of the following dashed sentence:- a test of AUTOMATIC ACTION at accelerated rate specified in 17.8.4DV.1 only applies.APRIL 7, 2017 NATIONAL DIFFERENCES FOR UL 60730-2-22 5UL COPYRIGHTED MATERIAL NOT AUTHORIZ

29、ED FOR FURTHER REPRODUCTION ORDISTRIBUTION WITHOUT PERMISSION FROM UL17.1.3.3DV D2 Modification:17.1.3.3DV.1 Not applicable.17.1.4DV D2 Modification:17.1.4DV.1 Not applicable.17.2.2DV D2 Modification:17.2.2DV.1 Not applicable.17.2.5DV D2 Modification:17.2.5DV.1 Not applicable.17.4DV D2 Modification:

30、17.4DV.1 Not applicable.17.6DV D2 Modification:17.6DV.1 Not applicable.17.7DV D2 Modification:17.7DV.1 Not applicable.17.8.4DV D2 Add the following:17.8.4DV.1 The number of automatic cycles shall be a minimum of 2000 cycles or asdeclared in Table 1DV. The cycling rate (on-off time), locked rotor or

31、overload current andpower factor shall be declared. A synthetic or artificial load may be used to simulate thetest parameters for this test.17.9DV D2 Modification:17.9DV.1 Not applicable.17.10DV D2 Modification:17.10DV.1 Not applicable.17.11DV D2 Modification:17.11DV.1 Not applicable.17.12DV D2 Modi

32、fication:17.12DV.1 Not applicable.APRIL 7, 2017NATIONAL DIFFERENCES FOR UL 60730-2-226UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION ORDISTRIBUTION WITHOUT PERMISSION FROM UL17.13DV D2 Modification:17.13DV.1 Not applicable.17.14DV D2 Add the following:17.14DV.1 The requirement in th

33、e second dash of 17.14 applies to off-winding protectors.The fourth dash applies to protectors that have deviation, drift and endurance valuesdeclared in Table 1DV. The fifth dash of 17.14 is not applicable.17.16DV D2 Modification:17.16DV.1 Not applicable.17.101.2.1.2DV D2 Modification of 17.101.2.1

34、.2:17.101.2.1.2DV.1 The first sentence of 17.101.2.1.2 should read, The test circuit shallcontain a series fuse complying with IEC 60269 or the Standard for Low-Voltage Fuses Part 1: General Requirements, UL 248-1.17.101.2.1.3DV DE Modification of 17.101.2.1.3:17.101.2.1.3DV.1 The reference to Table

35、 6 should refer to Table 6 in UL 60730-1.17.101.2.1.4DV DE Modification of the sentence starting with Cotton used shall .:17.101.2.1.4DV.1 The last sentence should read, Cotton used shall be as specified inAnnex C of UL 60730-1.Table 20.102DV DE Deletion:20.102DV.1 Delete Table 20.102 as these requi

36、rements do not apply to thermal motorprotector components.22DV D2 Modification to Clause 22:22DV.1 Clause 22 is not applicable.23DV D2 Modification to Clause 23:This clause of Part 1 is not applicable.BB17.205DV DE Modification of the seventh paragraph of BB17.205:BB17.205DV.1 If the thermal protect

37、or trips and cycles during the test, the temperatures ofTable BB.203DV.1 shall apply. If the thermal protector does not trip during the test, themaximum temperatures recorded during continuous operation shall not exceed 150 C forClass A, 165 C for Class E, 175 C for Class B, 200 C for Class F, 225 C

38、 for Class H, 245C for Class N and 265 C for Class R, namely, the arithmetic average values of TableBB.203DV.1.BB201DV DE Modify Table BB.201 by adding the following:APRIL 7, 2017 NATIONAL DIFFERENCES FOR UL 60730-2-22 7UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION ORDISTRIBUTION W

39、ITHOUT PERMISSION FROM ULF190H215N23R 255BB.203DV D2 Modify Table BB.203 by replacing with Table BB.203DV.1:Table BB.203DV.1 Maximum allowable temperatures for locked rotor conditionsType ofthermalmotorprotectorCondition Temperature of insulation CClass A Class E Class B Class F Class H Class N Clas

40、s RSelf-resettingDuring first hour maximum value200 215 225 250 275 295 315After first hour maximum value175 190 200 225 250 270 290 arithmeticaverage150 165 175 200 225 245 265Non-self-resetting maximum value 200 215 225 250 275 295 315Table CC.1DV Modify Table CC.1 by replacing with Table CC.1DV.1

41、:Table CC.1DV.1Mounted in-winding, sealed or varnished POLLUTION DEGREE 1Mounted on-winding, taped, sealed or varnished POLLUTION DEGREE 1Mounted on-winding unprotected POLLUTION DEGREE 2Mounted on-winding unprotected in appliances subject to condensationaPOLLUTION DEGREE 3Mounted off-winding sensin

42、g winding temperatureb, cPOLLUTION DEGREE 2Mounted off-winding sensing winding temperaturebin appliances subject tocondensationaPOLLUTION DEGREE 3Mounted inside the housing of a (semi)-hermetic compressordPOLLUTION DEGREE 1aThis situation occurs in appliances conforming to IEC 60335 which are classi

43、fied in whole or in part as POLLUTIONDEGREE 3 appliances.bThe key factor here is whether the MOTOR PROTECTOR is subjected to the internal pollution generated by themotor.cMOTOR PROTECTOR mounted off-winding are covered under the scope of this standard.dAs per 29.1 of IEC 60335-2-34:2012.APRIL 7, 2017NATIONAL DIFFERENCES FOR UL 60730-2-228