UL 486F-2014 UL Standard for Safety Bare and Covered Ferrules (First Edition Reprint with Revisions Through and Including January 12 2018)《安全的裸露和覆盖套圈的UL标准 (第一版)》.pdf

《UL 486F-2014 UL Standard for Safety Bare and Covered Ferrules (First Edition Reprint with Revisions Through and Including January 12 2018)《安全的裸露和覆盖套圈的UL标准 (第一版)》.pdf》由会员分享，可在线阅读，更多相关《UL 486F-2014 UL Standard for Safety Bare and Covered Ferrules (First Edition Reprint with Revisions Through and Including January 12 2018)《安全的裸露和覆盖套圈的UL标准 (第一版)》.pdf（26页珍藏版）》请在麦多课文档分享上搜索。

1、UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL UL 486F Bare and Covered FerrulesUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM ULUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REP

2、RODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL UL Standard for Safety for Bare and Covered Ferrules, UL 486F First Edition, Dated March 21, 2014 Summary of Topics This revision of the Standard for Bare and Covered Ferrules, UL 486F, includes modied requirements for plastic sleeve. Text that ha

3、s been changed in any manner or impacted by ULs electronic publishing system is marked with a vertical line in the margin. The revised requirements are substantially in accordance with Proposal(s) on this subject dated May 1, 2015. All rights reserved. No part of this publication may be reproduced,

4、stored in a retrieval system, or transmitted in any form by any means, electronic, mechanical photocopying, recording, or otherwise without prior permission of UL. UL provides this Standard as is without warranty of any kind, either expressed or implied, including but not limited to, the implied war

5、ranties of merchantability or tness for any purpose. In no event will UL be liable for any special, incidental, consequential, indirect or similar damages, including loss of prots, lost savings, loss of data, or any other damages arising out of the use of or the inability to use this Standard, even

6、if UL or an authorized UL representative has been advised of the possibility of such damage. In no event shall ULs liability for any damage ever exceed the price paid for this Standard, regardless of the form of the claim. Users of the electronic versions of ULs Standards for Safety agree to defend,

7、 indemnify, and hold UL harmless from and against any loss, expense, liability, damage, claim, or judgment (including reasonable attorneys fees) resulting from any error or deviation introduced while purchaser is storing an electronic Standard on the purchasers computer system. AUGUST 7, 2015 UL 486

8、F tr1UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL AUGUST 7, 2015 UL 486F tr2 No Text on This PageUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL Canadian Standards Association CSA

9、-C22.2 No. 291-14 First Edition Underwriters Laboratories Inc. UL 486F First Edition Bare and Covered Ferrules March 21, 2014 (Title Page Reprinted: August 7, 2015) ANSI/UL 486F-2015UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL Commitment

10、for Amendments This standard is issued jointly by the Canadian Standards Association (operating as “CSA Group”) and Underwriters Laboratories Inc. (UL). Comments or proposals for revisions on any part of the standard may be submitted to CSA Group or UL at any time. Revisions to this standard will be

11、 made only after processing according to the standards development procedures of CSA Group and UL. CSA Group and UL will issue revisions to this standard by means of a new edition or revised or additional pages bearing their date of issue. ISBN 978-1-77139-309-6 2015 CSA Group All rights reserved. N

12、o part of this publication may be reproduced in any form whatsoever without the prior permission of the publisher. This Standard is subject to periodic review, and suggestions for its improvement will be referred to the appropriate committee. To submit a proposal for change, please send the followin

13、g information to inquirescsagroup.org and include Proposal for change in the subject line: Standard designation (number); relevant clause, table, and/or gure number; wording of the proposed change; and rationale for the change. To purchase CSA Group Standards and related publications, visit CSA Grou

14、ps Online Store at shop.csa.ca or call toll-free 1-800-463-6727 or 416-747-4044. Copyright 2015 Underwriters Laboratories Inc. ULs Standards for Safety are copyrighted by UL. Neither a printed nor electronic copy of a Standard should be altered in any way. All of ULs Standards and all copyrights, ow

15、nerships, and rights regarding those Standards shall remain the sole and exclusive property of UL. This ANSI/UL Standard for Safety consists of the First Edition including revisions through August 7, 2015. The most recent designation of ANSI/UL 486F as an American National Standard (ANSI) occurred o

16、n August 7, 2015. ANSI approval for a standard does not include the Cover Page, Transmittal Pages, Title Page (front and back), or the Preface. Comments or proposals for revisions on any part of the Standard may be submitted to UL at any time. Proposals should be submitted via a Proposal Request in

17、ULs On-Line Collaborative Standards Development System (CSDS) at http:/. To purchase UL Standards, visit Comm 2000 at http:/m- or call toll-free 1-888-853-3503.UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL CONTENTS Preface .4 1 Scope .6 2

18、Reference Publications 6 2.1 Normative references .6 3 Units of Measurement .7 4 Denitions 7 5 Symbols and Abbreviations 7 6 Construction 7 6.1 General .7 6.2 Materials 8 6.3 Flammability .8 6.4 Thermal properties 8 7 Test Requirements 8 7.1 General .8 7.2 Tensile test 8 7.3 Mold stress relief 8A 7.

19、4 Dielectric voltage-withstand 9 8 Sampling Requirements .9 8.1 General .9 8.2 Tensile test 9 8.3 Mold stress test 9 8.4 Dielectric voltage-withstand 9 9 Test Methods .9 9.1 General .9 9.2 Tensile test .10 9.3 Mold stress test .10 9.4 Dielectric voltage withstand test .10 10 Marking, Labeling, and P

20、ackaging 10 10.1 General .10 AUGUST 7, 2015 CSA-C22.2 NO. 291-14 UL 486F 3UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL Preface This is the harmonized CSA Group and UL standard for Bare and Covered Ferrules. It is the rst edition of CSA C2

21、2.2 No. 291 and the rst edition of UL 486F. This harmonized standard has been jointly revised on August 7, 2015. This harmonized standard was prepared by the CSA Group and Underwriters Laboratories Inc. (UL). The efforts and support of the Technical Harmonization Committee for Connectors, of the Cou

22、ncil on the Harmonization of Electrotechnical Standards of the Nations of the Americas (CANENA), are gratefully acknowledged. This Standard is considered suitable for use for conformity assessment within the stated scope of the Standard. This standard was reviewed by the CSA Subcommittee on Wiring D

23、evices for Household and General Use, under the jurisdiction of the CSA Technical Committee on Wiring Products and the CSA Strategic Steering Committee on Requirements for Electrical Safety, and has been formally approved by the CSA Technical Committee. This standard has been approved by the America

24、n National Standards Institute (ANSI) as an American National Standard. Application of Standard Where reference is made to a specic number of samples to be tested, the specied number is to be considered a minimum quantity. Note: Although the intended primary application of this standard is stated in

25、 its scope, it is important to note that it remains the responsibility of the users of the standard to judge its suitability for their particular purpose. Level of Harmonization This standard uses the IEC format but is not based on, nor is it considered equivalent to, an IEC standard. This standard

26、is published as an equivalent standard for CSA Group and UL. An equivalent standard is a standard that is substantially the same in technical content, except as follows: Technical national differences are allowed for codes and governmental regulations as well as those recognized as being in accordan

27、ce with NAFTA Article 905, for example, because of fundamental climatic, geographical, technological, or infrastructural factors, scientic justication, or the level of protection that the country considers appropriate. Presentation is word for word except for editorial changes. Reasons for differenc

28、es from IEC At present there is no IEC standard for bare and covered ferrules. Therefore, this standard does not employ any IEC standard for base requirements. AUGUST 7, 2015 CSA-C22.2 NO. 291-14 UL 486F 4UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISS

29、ION FROM UL Interpretations The interpretation by the standards development organization of an identical or equivalent standard is based on the literal text to determine compliance with the standard in accordance with the procedural rules of the standards development organization. If more than one i

30、nterpretation of the literal text has been identied, a revision is to be proposed as soon as possible to each of the standards development organizations to more accurately reect the intent. CSA Effective Date The effective date for CSA International will be announced through CSA Informs or a CSA cer

31、tication notice. UL Effective Date A UL effective date is one established by UL LLC and is not part of the ANSI approved standard. AUGUST 7, 2015 CSA-C22.2 NO. 291-14 UL 486F 5UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL 1 Scope 1.1 These

32、 requirements cover bare and covered ferrules intended for eld wiring and factory wiring for use in accordance with the National Electrical Code, ANSI/NFPA-70 and Canadian Electrical Code, CSA C22.1. 1.2 These ferrules are intended to facilitate the connection of stranded wire on to devices, such as

33、 terminal blocks. Their purpose is to treat stripped wire and prevent turned back strands during installation. They are intended to be used to attach to one stranded copper conductor or two stranded copper conductors of the same size. 1.3 These ferrules are suitable for use with 1/0 20 AWG stranded

34、copper conductors. 1.4 These ferrules are intended to be terminated in wire connection devices rated for solid conductors. 1.5 Ferrules are not intended for use in IDC (insulation displacement connection) terminal blocks. 1.6 This standard does not apply to wire connectors such as pin adapters cover

35、ed in CSA C22.2 No. 65 or UL 486A-486B. 2 Reference Publications 2.1 Normative references Where reference is made to any Standards, such reference shall be considered to refer to the latest editions and revisions thereto available at the time of printing, unless otherwise specied. 2.1.1 CSA Standard

36、s C22.1-12 Canadian Electrical Code, Part I (CEC) CAN/CSA-C22.2 No. 0.17-00 (R2009) Evaluation of Properties of Polymeric Materials MARCH 21, 2014 CSA-C22.2 NO. 291-14 UL 486F 6UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL 2.1.2 UL Standar

37、ds UL 94 Tests for Flammability of Plastic Materials for Parts in Devices and Appliances UL 746C Polymeric Materials Use in Electrical Equipment Evaluations 2.1.3 NFPA* Standard ANSI/NFPA 70-2011, National Electrical Code (NEC) *National Fire Protection Association 3 Units of Measurement 3.1 The val

38、ues given in SI (metric) units shall be normative, except for AWG conductor sizes. Any other values given are for information only. 4 Denitions For the purpose of this Standard, the following terms and denitions apply. 4.1 Covered Encased within material of composition or thickness that is not recog

39、nized as electrical insulation. 4.1A Covered ferrule A ferrule provided with a plastic sleeve. 4.2 Ferrule A conductive sleeve used to facilitate the termination of stranded wire in devices used to terminate solid conductors. 4.3 Plastic sleeve A non-conductive plastic material used for identication

40、 purposes. The term covering is also referred to in the Standard as a plastic sleeve . 5 Symbols and Abbreviations 5.1 Degree 5.2 AWG American Wire Gage/gauge 5.3 C Celsius 5.4 mm 2 Squared millimeters 5.5 V Volts 6 Construction 6.1 General 6.1.1 A ferrule shall be provided with one opening to accep

41、t one or two stranded type copper conductors applied with compression tooling. AUGUST 7, 2015 CSA-C22.2 NO. 291-14 UL 486F 7UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL 6.1.2 A ferrule shall comply with the dimensional requirements in Tab

42、les15a n dFigures15 . Intermediate lengths and longer lengths are permissible. 6.2 Materials 6.2.1 A ferrule shall be of copper or a copper alloy containing at least 80% copper and be coated with tin. 6.2.2 A plastic sleeve shall be colored as dened in Tables 4 and 5. 6.3 Flammability 6.3.1 The cove

43、ring material shall have a minimum ammability classication of HB as determined by tests described in UL 94 or CAN/CSA-C22.2 No. 0.17. As an alternative, the covering shall meet the glow wire test as specied in UL 746C or CSA C22.2 No 0.17 for a temperature of 650 C. This ammability classication may

44、be determined at the minimum thickness employed in the construction or a nominal thickness of 0.8 mm (0.031 in), whichever is greater. 6.4 Thermal properties 6.4.1 A polymeric material used for covering shall have a minimum relative thermal index (RTI) of 80 C (176F) (electrical only). The material

45、shall be evaluated using the specimen thickness employed in the covering or a nominal thickness of 0.8 mm (0.031 in), whichever is greater. The electrical RTI value may be determined regardless of the color used for the plastic sleeve. 7 Test Requirements 7.1 General 7.1.1 All ferrules shall comply

46、with the test requirements in 7.2. Covered ferrules shall additionally comply with the test requirements in 7.3 7.4. 7.2 Tensile test 7.2.1 During testing in accordance with 9.2, the conductor shall not visibly move (with normal or corrected to normal vision) within the ferrule or be pulled out of t

47、he ferrule. AUGUST 7, 2015 CSA-C22.2 NO. 291-14 UL 486F 8UL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL 7.3 Mold stress relief 7.3.1 As a result of conditioning as specied in 9.3, there shall not be any warpage, shrinkage, or other distorti

48、on that results in interference with the operation, function, or installation of the device. AUGUST 7, 2015 CSA-C22.2 NO. 291-14 UL 486F 8AUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL AUGUST 7, 2015 CSA-C22.2 NO. 291-14 UL 486F 8B No Text

49、 on This PageUL COPYRIGHTED MATERIAL NOT AUTHORIZED FOR FURTHER REPRODUCTION OR DISTRIBUTION WITHOUT PERMISSION FROM UL 7.4 Dielectric voltage-withstand 7.4.1 The plastic sleeve of a covered ferrule shall withstand the applied potential without breakdown when tested in accordance with 9.4. 8 Sampling Requirements 8.1 General 8.1.1 The number of samples required for each test shall be as described in 8.2 8.4. 8.