TIA-41 511-E-2004 Part 511 Wireless Radiotelecommunications Intersystem Operations C ANS SS7 Transport Signaling Protocols《Part 511 无绳无线电通信内部系统操作 ANS SS7传输信令协议》.pdf

《TIA-41 511-E-2004 Part 511 Wireless Radiotelecommunications Intersystem Operations C ANS SS7 Transport Signaling Protocols《Part 511 无绳无线电通信内部系统操作 ANS SS7传输信令协议》.pdf》由会员分享，可在线阅读，更多相关《TIA-41 511-E-2004 Part 511 Wireless Radiotelecommunications Intersystem Operations C ANS SS7 Transport Signaling Protocols《Part 511 无绳无线电通信内部系统操作 ANS SS7传输信令协议》.pdf（18页珍藏版）》请在麦多课文档分享上搜索。

1、 TIA-41.511-E (Revision of TIA/EIA-41-D) April 2004Part 511: Wireless Radiotelecommunications Intersystem Operations ANS/SS7 Transport Signaling Protocols ANSI/TIA-41.511-E-2004 APPROVED: APRIL 20, 2004 REAFFIRMED: MAY 28, 2013 NOTICE TIA Engineering Standards and Publications are designed to serve

2、the public interest through eliminating misunderstandings between manufacturers and purchasers, facilitating interchangeability and improvement of products, and assisting the purchaser in selecting and obtaining with minimum delay the proper product for their particular need. The existence of such S

3、tandards and Publications shall not in any respect preclude any member or non-member of TIA from manufacturing or selling products not conforming to such Standards and Publications. Neither shall the existence of such Standards and Publications preclude their voluntary use by Non-TIA members, either

4、 domestically or internationally. Standards and Publications are adopted by TIA in accordance with the American National Standards Institute (ANSI) patent policy. By such action, TIA does not assume any liability to any patent owner, nor does it assume any obligation whatever to parties adopting the

5、 Standard or Publication. This Standard does not purport to address all safety problems associated with its use or all applicable regulatory requirements. It is the responsibility of the user of this Standard to establish appropriate safety and health practices and to determine the applicability of

6、regulatory limitations before its use. (From Project No. ANSI/TIA-PN-41.511-RV5-RF1, formulated under the cognizance of the TIA TR-45 Mobile (b) there is no assurance that the Document will be approved by any Committee of TIA or any other body in its present or any other form; (c) the Document may b

7、e amended, modified or changed in the standards development or any editing process. The use or practice of contents of this Document may involve the use of intellectual property rights (“IPR”), including pending or issued patents, or copyrights, owned by one or more parties. TIA makes no search or i

8、nvestigation for IPR. When IPR consisting of patents and published pending patent applications are claimed and called to TIAs attention, a statement from the holder thereof is requested, all in accordance with the Manual. TIA takes no position with reference to, and disclaims any obligation to inves

9、tigate or inquire into, the scope or validity of any claims of IPR. TIA will neither be a party to discussions of any licensing terms or conditions, which are instead left to the parties involved, nor will TIA opine or judge whether proposed licensing terms or conditions are reasonable or non-discri

10、minatory. TIA does not warrant or represent that procedures or practices suggested or provided in the Manual have been complied with as respects the Document or its contents. If the Document contains one or more Normative References to a document published by another organization (“other SSO”) engag

11、ed in the formulation, development or publication of standards (whether designated as a standard, specification, recommendation or otherwise), whether such reference consists of mandatory, alternate or optional elements (as defined in the TIA Engineering Manual, 4thedition) then (i) TIA disclaims an

12、y duty or obligation to search or investigate the records of any other SSO for IPR or letters of assurance relating to any such Normative Reference; (ii) TIAs policy of encouragement of voluntary disclosure (see Engineering Manual Section 6.5.1) of Essential Patent(s) and published pending patent ap

13、plications shall apply; and (iii) Information as to claims of IPR in the records or publications of the other SSO shall not constitute identification to TIA of a claim of Essential Patent(s) or published pending patent applications. TIA does not enforce or monitor compliance with the contents of the

14、 Document. TIA does not certify, inspect, test or otherwise investigate products, designs or services or any claims of compliance with the contents of the Document. ALL WARRANTIES, EXPRESS OR IMPLIED, ARE DISCLAIMED, INCLUDING WITHOUT LIMITATION, ANY AND ALL WARRANTIES CONCERNING THE ACCURACY OF THE

15、 CONTENTS, ITS FITNESS OR APPROPRIATENESS FOR A PARTICULAR PURPOSE OR USE, ITS MERCHANTABILITY AND ITS NONINFRINGEMENT OF ANY THIRD PARTYS INTELLECTUAL PROPERTY RIGHTS. TIA EXPRESSLY DISCLAIMS ANY AND ALL RESPONSIBILITIES FOR THE ACCURACY OF THE CONTENTS AND MAKES NO REPRESENTATIONS OR WARRANTIES RE

16、GARDING THE CONTENTS COMPLIANCE WITH ANY APPLICABLE STATUTE, RULE OR REGULATION, OR THE SAFETY OR HEALTH EFFECTS OF THE CONTENTS OR ANY PRODUCT OR SERVICE REFERRED TO IN THE DOCUMENT OR PRODUCED OR RENDERED TO COMPLY WITH THE CONTENTS. TIA SHALL NOT BE LIABLE FOR ANY AND ALL DAMAGES, DIRECT OR INDIR

17、ECT, ARISING FROM OR RELATING TO ANY USE OF THE CONTENTS CONTAINED HEREIN, INCLUDING WITHOUT LIMITATION ANY AND ALL INDIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES (INCLUDING DAMAGES FOR LOSS OF BUSINESS, LOSS OF PROFITS, LITIGATION, OR THE LIKE), WHETHER BASED UPON BREACH OF CONTRACT, BREACH

18、 OF WARRANTY, TORT (INCLUDING NEGLIGENCE), PRODUCT LIABILITY OR OTHERWISE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. THE FOREGOING NEGATION OF DAMAGES IS A FUNDAMENTAL ELEMENT OF THE USE OF THE CONTENTS HEREOF, AND THESE CONTENTS WOULD NOT BE PUBLISHED BY TIA WITHOUT SUCH LIMITATIONS. TIA-

19、41-511-E123456789101112131415161718192021222324252627282930313233343536373839404142434445464748495051525354555657585960511-1 Message Transfer PartPART 5111 MESSAGE TRANSFER PARTThe MTP is defined in ANSI T1.111, with the following supplemental information.The MAP messages that are transported on an

20、intersystem basis may be assigned a message priorityvalue of either 0 or 1. The INVOKE, RETURN RESULT, RETURN ERROR, and REJECTcomponents associated with the same operation (e.g., FacilitiesDirective) shall have the samemessage priority value. The operations with message priority value 1 are listed

21、below. All othershave message priority value 0. The message priority value may be determined by the TIA-41 MAP based on the message type andmay be passed down to the MTP through the SCCP. In the case when a REJECT component is to bereturned, the message priority of the REJECT component should be the

22、 same as that of the rejectedmessage.Table 1 TIA-41 Operations having MTP Message Priority Value 1TIA-41 OperationFacilitiesDirective2FacilitiesDirectiveFacilitiesReleaseHandoffBack2HandoffBackHandoffToThirdHandoffToThird2InterSystemAnswer (see note a) Notes:a. The MTP Message Priority value for the

23、 InterSystemAnswer has changed in rev. EMobileOnChannelRedirectionDirectiveRedirectionRequestTransferToNumberRequestTIA-41-511-ESignaling Connection Control Part123456789101112131415161718192021222324252627282930313233343536373839404142434445464748495051525354555657585960511-22 SIGNALING CONNECTION

24、CONTROL PARTFor TIA-41 applications, the SCCP is defined in ANSI T1.112, with the following exceptions andlimitations: SCCP Class 0 connectionless service is requested from the SCCP. (However, in accordancewith SCCP procedures, if a TIA-41 message is segmented by the SCCP, the sequence of XUDTmessag

25、es carrying the segments are sent using SCCP Class 1 sequenced connectionless service.The In-Sequence Delivery Option field of the segmentation parameter within each of the XUDTmessages is set to 0 to reflect the original request for Class 0 service.) Whether to set the return message on error or di

26、scard message on error option in the ProtocolClass parameter of the UDT or XUDT message is at the discretion of the implementation. Ifreturn message on error is requested by the SCCP user for a segmented message, then only thefirst XUDT message sent shall have return message on error requested. The

27、TIA-41 Mobile Application Part has assigned the following Subsystem Numbers (SSN).Use of the following SSN values is recommended1:5: Mobile Application Part (MAP)6: Home Location Register (HLR)7: Visitor Location Register (VLR)8: Mobile Switching Center (MSC)9: Equipment Identification Register (EIR

28、) (reserved)210: Authentication Center (AC)11: Short Message Service (SMS)12: Over-The-Air Service Provisioning Function (OTAF) In accordance with ANSI T1.112 an SSN shall be included in all messages even if messagerouting is based on Global Title Translation (GTT). The null SSN (i.e., value 0) shou

29、ld be usedwhen the subsystem is not known (e.g., before a global title translation takes place) per ANSIT1.112. Global title addresses are required in the SCCP Called Party Address and the SCCP CallingParty Address for international roaming purposes.1Further SSN assignments are not planned.2Detailed

30、 transactions relative to SSN value 9 are for further study.TIA-41-511-E123456789101112131415161718192021222324252627282930313233343536373839404142434445464748495051525354555657585960511-3 Signaling Connection Control Part Global Title Translation on Mobile Identification Number can be used for comm

31、unication withthe HLR on the ANSI SS7 network1. The following encoding may be used:Table 2 ANSI SS7 - MIN to HLR Global TitleField Sub-field ValueAddress Indicator SSN Indicator 1Point Code Indicator 0 or 1Global Title Indicator 2 (00102)Routing Indicator 0National or International Indicator1 (Natio

32、nal use)Subsystem Number Include applicable value if known or zero.Global Title Translation Type 3 (000000112) “Cellular Nationwide Roaming Service“Address Information MIN1An administrative set of SS7 nodes that are interconnected by a common national signaling point code addressing scheme.TIA-41-51

33、1-ESignaling Connection Control Part123456789101112131415161718192021222324252627282930313233343536373839404142434445464748495051525354555657585960511-4 Global Title Translation on Mobile Identification Number can be used for communication witha Message Center on the ANSI SS7 network. The following

34、encoding may be used:Table 3 ANSI SS7 - MIN to MC Global TitleField Sub-field ValueAddress Indicator SSN Indicator 1Point Code Indicator 0 or 1Global Title Indicator 2 (00102)Routing Indicator 0National or International Indicator1 (National use)Subsystem Number Include applicable value if known or z

35、ero.Global Title Translation Type 12 (000011002) “Wireless MIN-Based Short Message Service“Address Information MINTIA-41-511-E123456789101112131415161718192021222324252627282930313233343536373839404142434445464748495051525354555657585960511-5 Signaling Connection Control Part Global Title Translatio

36、n on IMSI (ITU-T E.212 International Mobile Subscriber Identity) canbe used for communication from a Serving System (MSC or VLR) to an HLR on the same or adifferent national SS7 network using the IMSI of a roaming mobile. It may also be used forcommunication to any network element that is identified

37、 by an E.212 formatted address on thesame or a different SS7 network. The following encoding may be used: Table 4 ANSI SS7 - E.212 Global TitleField Sub-field ValueAddress Indicator SSN Indicator 1Point Code Indicator 0 or 1Global Title Indicator 2 (00102)Routing Indicator 0National or International

38、 Indicator1 (National use)Subsystem Number Include applicable value if known or zero.Global Title Translation Type 16 (000100002) Cellular/PCS Interworking (see note a)Notes:a. Translation Type 9 may be used in some networks based on the initial IS-807 recom-mendation.Address Information IMSI or oth

39、er E.212 formatted addressTIA-41-511-ESignaling Connection Control Part123456789101112131415161718192021222324252627282930313233343536373839404142434445464748495051525354555657585960511-6 Global Title Translation on an E.164 number (e.g., Mobile Directory Number) can be used forcommunication to an H

40、LR on the same or a different national SS7 network based on the MobileDirectory Number. The following encoding may be used:Table 5 ANSI SS7 - MDN to HLR (E.164) Global TitleField Sub-field ValueAddress Indicator SSN Indicator 1Point Code Indicator 0 or 1Global Title Indicator 2 (00102)Routing Indica

41、tor 0National or International Indicator1 (National use)Subsystem Number Include applicable value if known or zero.Global Title Translation Type 14 (000011102) “Mobile Subscriber Addressing“Address Information E.164 Mobile Directory NumberTIA-41-511-E1234567891011121314151617181920212223242526272829

42、30313233343536373839404142434445464748495051525354555657585960511-7 Signaling Connection Control Part Global Title Translation on an E.164 number (e.g., Mobile Directory Number) can be used forcommunication to an MC on the same or a different national SS7 network based on the MobileDirectory Number.

43、 The following encoding may be used:Table 6 ANSI SS7 - MDN to MC (E.164) Global TitleField Sub-field ValueAddress Indicator SSN Indicator 1Point Code Indicator 0 or 1Global Title Indicator 2 (00102)Routing Indicator 0National or International Indicator1 (National use)Subsystem Number Include applica

44、ble value if known or zero.Global Title Translation Type 17 (000100012) “Mobile Subscriber Message Center Addressing“Address Information E.164 Mobile Directory NumberTIA-41-511-ESignaling Connection Control Part12345678910111213141516171819202122232425262728293031323334353637383940414243444546474849

45、5051525354555657585960511-8 Global Title Translation on IMSI can be used for communication from a Serving System (MSCor VLR) to a Message Center on the same or a different national SS7 network. The followingencoding may be used:Table 7 ANSI SS7 - IMSI to MC Global TitleField Sub-field ValueAddress I

46、ndicator SSN Indicator 1Point Code Indicator 0 or 1Global Title Indicator 2 (00102)Routing Indicator 0National or International Indicator1 (National use)Subsystem Number Include applicable value if known or zero.Global Title Translation Type 13 (000011012) “Wireless IMSI-based Short Message Service“

47、Address Information IMSITIA-41-511-E123456789101112131415161718192021222324252627282930313233343536373839404142434445464748495051525354555657585960511-9 Signaling Connection Control Part Global Title Translation on portable Directory Number can be used for communication with theNPDB. The following e

48、ncoding may be used:Table 8 ANSI SS7 - DN to NPDB Global TitleField Sub-field ValueAddress Indicator SSN Indicator 1Point Code Indicator 0 or 1Global Title Indicator 2 (00102)Routing Indicator 0National or International Indicator1 (National use)Subsystem Number Include applicable value if known or z

49、ero.Global Title Translation Type 11 (000010112) “Internetwork Number Portability Query/Response“Address Information E.164 Directory NumberTIA-41-511-ESignaling Connection Control Part123456789101112131415161718192021222324252627282930313233343536373839404142434445464748495051525354555657585960511-10 Global Title Translation can be used for communication with a Service Control Point (SCP).The following encoding may be used: When an originating network entity sends an SS7 message within a national SS7 signalingnetwork with a global title in the SCCP called party address fiel