TIA-1040 1 07-2006 Regenerative Satellite Mesh-A (RMS-A) Air Interface - Physical Layer Specification - Part 7 Synchronization《再生卫星Mesh-A (RMS-A)空中接口 物理层规范第7部分 同步》.pdf

《TIA-1040 1 07-2006 Regenerative Satellite Mesh-A (RMS-A) Air Interface - Physical Layer Specification - Part 7 Synchronization《再生卫星Mesh-A (RMS-A)空中接口 物理层规范第7部分 同步》.pdf》由会员分享，可在线阅读，更多相关《TIA-1040 1 07-2006 Regenerative Satellite Mesh-A (RMS-A) Air Interface - Physical Layer Specification - Part 7 Synchronization《再生卫星Mesh-A (RMS-A)空中接口 物理层规范第7部分 同步》.pdf（25页珍藏版）》请在麦多课文档分享上搜索。

1、 TIA STANDARD Regenerative Satellite Mesh-A (RSM-A) Air Interface - Physical Layer Specification - Part 7: Synchronization TIA-1040.1.07 May 2006TELECOMMUNICATIONS INDUSTRY ASSOCIATION The Telecommunications Industry Association represents the communications sector of NOTICE OF COPYRIGHT This docume

2、nt is copyrighted by the TIA. Reproduction of these documents either in hard copy or soft copy (including posting on the web) is prohibited without copyright permission. This document contains significant portions of material copied from ETSI document number TS 102188-5v112. The copyright on the ETS

3、I document is owned by the European Telecommunication Standards Institute, which has granted a license for reproduction for use by TIA and its Engineering Committees and Subcommittees. Any copies of the above-mentioned ETSI document(s) required for other purposes should be purchased directly from ET

4、SI or other organizations with a sales agreement covering ETSI publications. For copyright permission to reproduce portions of this document, please contact the TIA Standards Department or go to the TIA website (www.tiaonline.org) for details on how to request permission. Details are located at: htt

5、p:/www.tiaonline.org/about/faqDetail.cfm?id=18 OR Telecommunications Industry Association Standards (b) there is no assurance that the Document will be approved by any Committee of TIA or any other body in its present or any other form; (c) the Document may be amended, modified or changed in the sta

6、ndards development or any editing process. The use or practice of contents of this Document may involve the use of intellectual property rights (“IPR”), including pending or issued patents, or copyrights, owned by one or more parties. TIA makes no search or investigation for IPR. When IPR consisting

7、 of patents and published pending patent applications are claimed and called to TIAs attention, a statement from the holder thereof is requested, all in accordance with the Manual. TIA takes no position with reference to, and disclaims any obligation to investigate or inquire into, the scope or vali

8、dity of any claims of IPR. TIA will neither be a party to discussions of any licensing terms or conditions, which are instead left to the parties involved, nor will TIA opine or judge whether proposed licensing terms or conditions are reasonable or non-discriminatory. TIA does not warrant or represe

9、nt that procedures or practices suggested or provided in the Manual have been complied with as respects the Document or its contents. TIA does not enforce or monitor compliance with the contents of the Document. TIA does not certify, inspect, test or otherwise investigate products, designs or servic

10、es or any claims of compliance with the contents of the Document. ALL WARRANTIES, EXPRESS OR IMPLIED, ARE DISCLAIMED, INCLUDING WITHOUT LIMITATION, ANY AND ALL WARRANTIES CONCERNING THE ACCURACY OF THE CONTENTS, ITS FITNESS OR APPROPRIATENESS FOR A PARTICULAR PURPOSE OR USE, ITS MERCHANTABILITY AND

11、ITS NON-INFRINGEMENT OF ANY THIRD PARTYS INTELLECTUAL PROPERTY RIGHTS. TIA EXPRESSLY DISCLAIMS ANY AND ALL RESPONSIBILITIES FOR THE ACCURACY OF THE CONTENTS AND MAKES NO REPRESENTATIONS OR WARRANTIES REGARDING THE CONTENTS COMPLIANCE WITH ANY APPLICABLE STATUTE, RULE OR REGULATION, OR THE SAFETY OR

12、HEALTH EFFECTS OF THE CONTENTS OR ANY PRODUCT OR SERVICE REFERRED TO IN THE DOCUMENT OR PRODUCED OR RENDERED TO COMPLY WITH THE CONTENTS. TIA SHALL NOT BE LIABLE FOR ANY AND ALL DAMAGES, DIRECT OR INDIRECT, ARISING FROM OR RELATING TO ANY USE OF THE CONTENTS CONTAINED HEREIN, INCLUDING WITHOUT LIMIT

13、ATION ANY AND ALL INDIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES (INCLUDING DAMAGES FOR LOSS OF BUSINESS, LOSS OF PROFITS, LITIGATION, OR THE LIKE), WHETHER BASED UPON BREACH OF CONTRACT, BREACH OF WARRANTY, TORT (INCLUDING NEGLIGENCE), PRODUCT LIABILITY OR OTHERWISE, EVEN IF ADVISED OF THE

14、POSSIBILITY OF SUCH DAMAGES. THE FOREGOING NEGATION OF DAMAGES IS A FUNDAMENTAL ELEMENT OF THE USE OF THE CONTENTS HEREOF, AND THESE CONTENTS WOULD NOT BE PUBLISHED BY TIA WITHOUT SUCH LIMITATIONS. TIA SHALL NOT BE LIABLE FOR ANY AND ALL DAMAGES, DIRECT OR INDIRECT, ARISING FROM OR RELATING TO ANY U

15、SE OF THE CONTENTS CONTAINED HEREIN, INCLUDING WITHOUT LIMITATION ANY AND ALL INDIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES (INCLUDING DAMAGES FOR LOSS OF BUSINESS, LOSS OF PROFITS, LITIGATION, OR THE LIKE), WHETHER BASED UPON BREACH OF CONTRACT, BREACH OF WARRANTY, TORT (INCLUDING NEGLIGEN

16、CE), PRODUCT LIABILITY OR OTHERWISE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. THE FOREGOING NEGATION OF DAMAGES IS A FUNDAMENTAL ELEMENT OF THE USE OF THE CONTENTS HEREOF, AND THESE CONTENTS WOULD NOT BE PUBLISHED BY TIA WITHOUT SUCH LIMITATIONS. TIA 1040.1.07 1Contents Intellectual Prope

17、rty Rights4 Foreword 4 1 Scope5 2 References 5 3 Definitions and abbreviations.5 3.1 Definitions. 5 3.2 Abbreviations 5 4 General description of synchronization system6 4.1 System timing structure 8 4.2 General requirement 8 4.2.1 Timing and frequency reference point 8 4.2.2 ST requirement 8 4.2.3 N

18、etwork requirement. 8 4.2.4 Measurement conditions . 8 5 Timing synchronization9 5.1 Introduction . 9 5.2 Frequency accuracy and stability 9 5.2.1 ST Frequency accuracy and stability 9 5.3 Timing error 9 5.3.1 Initial ST timing error . 9 5.3.2 ST Timing error. 9 5.4 Time of Day information 9 5.4.1 T

19、oD definition . 9 5.4.2 ToD format 10 5.4.3 UTC time. 11 5.5 Beacon transmission (Satellite to ST direction). 11 5.5.1 Superframe 11 5.5.2 Frame alignment 11 5.5.3 Beacon burst structure. 12 5.5.3.1 Beam settling bit pattern 13 5.5.3.2 Unique Word bit pattern 14 5.5.3.3 PN sequence bit pattern. 14 5

20、.6 Early/Late timing measurement field . 15 5.7 Initial timing acquisition. 15 5.8 Timing synchronization maintenance. 15 6 Frequency synchronization 16 6.1 Calculate the Initial Doppler value. 16 Annex A (normative): Timing calculations17 A.1 General description 17 A.1.1 Calculation of Path Length

21、. 17 A.1.2 GPS accuracy 17 A.2 Calculate the timing offset .17 Annex B (informative): Bibliography.18 History 19 TIA 1040.1.07 2Intellectual Property Rights IPRs essential or potentially essential to the present document may have been declared to ETSI. The information pertaining to these essential I

22、PRs, if any, is publicly available for ETSI members and non-members, and can be found in ETSI SR 000 314: “Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards“, which is available from the ETSI Secretariat. Latest updates are a

23、vailable on the ETSI Web server (http:/webapp.etsi.org/IPR/home.asp). Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web

24、 server) which are, or may be, or may become, essential to the present document. Satellite Earth Stations and Systems (SES); Regenerative Satellite Mesh - A (RSM-A) air interface; Physical layer specification; Part 7: Synchronization Foreword This Technical Specification (TS) has been produced by ET

25、SI Technical Committee Satellite Earth Stations and Systems (SES). The present document is part 7 of a multi-part deliverable covering the BSM Regenerative Satellite Mesh - A (RSM-A) air interface; Physical layer specification, as identified below: Part 1: “General description“; Part 2: “Frame struc

26、ture“; Part 3: “Channel coding“; Part 4: “Modulation“; Part 5: “Radio transmission and reception“; Part 6: “Radio link control“; Part 7: “Synchronization“. TIA 1040.1.07 31 Scope The present document presents the requirements for synchronizing timing and frequency between the ST and the satellite ne

27、twork within the TC-SES BSM Regenerative Satellite Mesh - A (RSM-A) air interface family. 2 References The following documents contain provisions which, through reference in this text, constitute provisions of the present document. References are either specific (identified by date of publication an

28、d/or edition number or version number) or non-specific. For a specific reference, subsequent revisions do not apply. For a non-specific reference, the latest version applies. Referenced documents which are not found to be publicly available in the expected location might be found at http:/docbox.ets

29、i.org/Reference. 1 ETSI TS 102 189-2: “Satellite Earth Stations and Systems (SES); Regenerative Satellite Mesh - A (RSM-A) air interface; MAC/SLC layer specification; Part 2: MAC layer“. 2 IETF RFC 1305: “Network Time Protocol (Version 3) Specification, Implementation and Analysis“. 3 Definitions an

30、d abbreviations 3.1 Definitions For the purposes of the present document, the following terms and definitions apply: Network Operations Control Centre (NOCC): centre that controls the access of the satellite terminal to an IP network and also provides element management functions and control of the

31、address resolution and resource management functionality satellite payload: part of the satellite that provides air interface functions NOTE: The satellite payload operates as a packet switch that provides direct unicast and multicast communication between STs at the link layer. Satellite Terminal (

32、ST): terminal installed in the user premises terrestrial host: entity on which application level programs are running NOTE: It may be connected directly to the Satellite Terminal or through one or more networks. 3.2 Abbreviations For the purposes of the present document, the following abbreviations

33、apply: AWGN Additive White Gaussian Noise BPSK Binary Phase Shift Keying ECEF Earth Centred Earth Fixed IP Internet Protocol kbps kilo bits per second (thousands of bits per second) LHCP Left Hand Circular Polarization TIA 1040.1.07 4LLA Latitude, Longitude and Altitude LSB Least Significant Bit MIP

34、 Management Information Packet MMI Man Machine Interface NOCC Network Operations Control Centre PHY PHYsical PN Pseudo NoisePTP Point-to-Point QPSK Quaternary Phase Shift Keying RHCP Right Hand Circular Polarization RSM Regenerative Satellite Mesh SLC Satellite Link Control ST Satellite Terminal TDM

35、A Time Division Multiple Access TIP Transmission Information Packet ToD Time of Day ULPC UpLink Power Control UTC Universal Coordinated Time UW Unique Word 4 General description of synchronization system BSM RSM-A is a multi-spot beam, multicarrier, synchronous system where the timing and frequency

36、on the satellite serve as the reference to synchronize the TDMA transmissions for the STs, and other network elements. The satellite includes a packet switch designed to provide single-hop, point to point packet routing between downlink cells. The functions of the physical layer are different for th

37、e uplink and downlink. The major functions are illustrated in figure 4. The present document describes the synchronization functions - this group of functions is highlighted in figure 4. TIA 1040.1.07 5UPLINK DOWNLINK Part 3:Channel coding Part 2:Frame structure Part 4:Modulation Part 5:Radio transm

38、ission and reception Part 7:Synchronization Block interleaving Inner coding(convolutional)Downlink burst building Downlink modulation (QPSK) ST receiver ScramblingAssemble packets into code blocks Outer coding (Reed-Solomon)No interleavingInner coding(hamming)Uplink burst building Uplink modulation(

39、OQPSK) Part 6: Radio link controlScramblingAssemble packets into code blocks Outer coding (Reed-Solomon) Timing and frequency control ST transmitter Figure 4: Physical layer functions The timing synchronization requirements are described in clause 5, and the frequency synchronization requirements ar

40、e described in clause 6. Synchronization in the RSM-A system is composed of three major tasks: timing synchronization; frequency synchronization; frame synchronization; A master oscillator onboard the RSM-A spacecraft is the primary reference for all synchronization processes. The fundamental goal o

41、f synchronization is to have all STs operate such that all bursts arrive at the satellite synchronized in timing and frequency. TIA 1040.1.07 64.1 System timing structure The RSM-A satellite system is a TDMA system. Timing configuration in the system is composed of superframe, frame, timeslot, symbo

42、l and bit. One superframe equals to 768 ms, and is divided into eight uplink frames or 256 downlink frames. The downlink frame counter is called the Time of Day (ToD) counter. Each uplink frame has 32 timeslots. The uplink frame duration is 96 ms, one timeslot duration is 3 ms. Each symbol correspon

43、ds to 2 bits. The complete uplink and downlink frame structure is defined in BSM RSM-A Physical Layer Specification, TS 102 188-2. A superframe always starts from the first time slot in a frame that meets ToD mod 256 = 0. An Uplink frame always starts with time slot 0 when ToD mod 32 = 0. 4.2 Genera

44、l requirement 4.2.1 Timing and frequency reference point The satellite is selected to be the reference point for both timing and frequency. 4.2.2 ST requirement The ST timing and frequency requirements are: Both transmitter and receiver timing shall be derived from the same timebase. Both transmitte

45、r and receiver frequency shall be derived from the same frequency source. The ST shall use the same source for both RF frequency generation and the timebase generator. All return link signals (control and user data) transmitted from the STs shall achieve frame/timeslot alignment on the satellite tim

46、ing reference point, i.e. input of satellite antenna. In various operation modes, synchronization shall be maintained under the worst case timing and frequency drift rate due to ST-satellite relative motion and ST master oscillator stability. The ST oscillator short-term stability shall maintain all

47、 timing offset, frequency offset and symbol rate requirement specified in BSM RSM-A physical layer specification, TS 102 188-5. 4.2.3 Network requirement The Network timing and frequency requirements are: The network should make multiple rate and volume timeslot assignments on the same uplink freque

48、ncy or with the same carrier designator (see BSM RSM-A physical layer specification, TS 102 188-5) as far as possible. When assigning timeslots on different carrier designators the network shall provide at least 3 ms guard time for the ST to switch between the two different transmit frequencies. An

49、ST may ignore assignments which it cannot use. At ST initialization, the network shall be able to estimate the slotted aloha signal arrival to the accuracy better than 15 Hz 1-sigma in frequency, 2,6 s 1-sigma in timing, under the condition of AWGN channel. 4.2.4 Measurement conditions In the present document, all timing and frequency related parameters are defined under the condition of AWGN channel, when the Beacon is received at a C/No = 78 dB-Hz minimum. Unless specified otherwise, all timing and frequency related parameters are defined as 1-sigma v