SANS 61047-2005 DC or AC supplied electronic step-down convertors for filament lamps - Performance requirements《白炽灯上的直流或交流供电式电子降压转换器 性能要求》.pdf

《SANS 61047-2005 DC or AC supplied electronic step-down convertors for filament lamps - Performance requirements《白炽灯上的直流或交流供电式电子降压转换器 性能要求》.pdf》由会员分享，可在线阅读，更多相关《SANS 61047-2005 DC or AC supplied electronic step-down convertors for filament lamps - Performance requirements《白炽灯上的直流或交流供电式电子降压转换器 性能要求》.pdf（21页珍藏版）》请在麦多课文档分享上搜索。

1、 Collection of SANS standards in electronic format (PDF) 1. Copyright This standard is available to staff members of companies that have subscribed to the complete collection of SANS standards in accordance with a formal copyright agreement. This document may reside on a CENTRAL FILE SERVER or INTRA

2、NET SYSTEM only. Unless specific permission has been granted, this document MAY NOT be sent or given to staff members from other companies or organizations. Doing so would constitute a VIOLATION of SABS copyright rules. 2. Indemnity The South African Bureau of Standards accepts no liability for any

3、damage whatsoever than may result from the use of this material or the information contain therein, irrespective of the cause and quantum thereof. ICS 29.140.20 ISBN 0-626-16339-0 SANS 61047:2005 Edition 2 IEC 61047:2004 Edition 2SOUTH AFRICAN NATIONAL STANDARD DC or AC supplied electronic step-down

4、 convertors for filament lamps Performance requirements This national standard is the identical implementation of IEC 61047:2004 and is adopted with the permission of the International Electrotechnical Commission. Published by Standards South Africa 1 dr lategan road groenkloof private bag x191 pret

5、oria 0001 tel: 012 428 7911 fax: 012 344 1568 international code + 27 12 www.stansa.co.za Standards South Africa This standard may only be used and printed by approved subscription and freemailing clients of the SABS.SANS 61047:2005 Edition 2 IEC 61047:2004 Edition 2 Table of changes Change No. Date

6、 Scope Abstract Specifies performance requirements for electronic step-down convertors for use on d.c. supplies up to 250 V and a.c. supplies up to 1 000 V at 50 Hz or 60 Hz with operating frequencies deviating from the supply frequency, associated with tungsten halogen lamps as specified in SANS 60

7、357 and other filament lamps. Keywords electric convertors, electric lamps, filament lamps, step-down convertors. National foreword This South African standard was approved by National Committee StanSA SC 64A, Lighting and optics Lamps and auxiliaries, in accordance with procedures of Standards Sout

8、h Africa, in compliance with annex 3 of the WTO/TBT agreement. This SANS edition cancels and replaces SABS edition 1.2 (SABS IEC 61047:2001). This standard may only be used and printed by approved subscription and freemailing clients of the SABS. NORME INTERNATIONALE CEI IECINTERNATIONAL STANDARD 61

9、047 Deuxime dition Second edition 2004-06Convertisseurs abaisseurs lectroniques aliments en courant continu ou alternatif pour lampes incandescence Exigences de performances DC or AC supplied electronic step-down convertors for filament lamps Performance requirements Pour prix, voir catalogue en vig

10、ueur For price, see current catalogue IEC 2004 Droits de reproduction rservs Copyright - all rights reserved Aucune partie de cette publication ne peut tre reproduite ni utilise sous quelque forme que ce soit et par aucun procd, lectronique ou mcanique, y compris la photocopie et les microfilms, san

11、s laccord crit de lditeur. No part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from the publisher. International Electrotechnical Commission, 3, rue de Varemb, PO Box 131,

12、 CH-1211 Geneva 20, Switzerland Telephone: +41 22 919 02 11 Telefax: +41 22 919 03 00 E-mail: inmailiec.ch Web: www.iec.ch CODE PRIX PRICE CODE Q Commission Electrotechnique Internationale International Electrotechnical Commission This standard may only be used and printed by approved subscription a

13、nd freemailing clients of the SABS.61047 IEC:2004 3 CONTENTS FOREWORD.5 INTRODUCTION.9 1 Scope.11 2 Normative references.11 3 Terms and definitions .11 4 General notes on tests .13 5 Classification15 5.1 Classification according to the load .15 5.2 Classification according to output voltage15 6 Mark

14、ing15 6.1 Mandatory marking15 6.2 Optional marking.15 7 Output voltage and current .17 7.1 Open-circuit voltage17 7.2 Voltage during operation.17 7.3 Voltage surges during switching and operation17 7.4 Voltage waveform17 7.5 Inrush current17 8 Total circuit power19 9 Circuit power factor19 10 Supply

15、 current19 11 Impedance at audio-frequencies.19 12 Operational tests for abnormal conditions.19 13 Endurance21 Annex A (normative) Tests.23 Annex B (informative) A guide to quoting product life and failure rate 31 Bibliography32 Figure A.1 Measurement of currents 27 Figure A.2 Measurement of impedan

16、ce at audio-frequencies .29 This standard may only be used and printed by approved subscription and freemailing clients of the SABS.61047 IEC:2004 5 INTERNATIONAL ELECTROTECHNICAL COMMISSION _ DC OR AC SUPPLIED ELECTRONIC STEP-DOWN CONVERTORS FOR FILAMENT LAMPS PERFORMANCE REQUIREMENTS FOREWORD 1) T

17、he International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international co-operation on all questions concerning standardization in the electrical a

18、nd electronic fields. To this end and in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their preparation is entrusted to technical c

19、ommittees; any IEC National Committee interested in the subject dealt with may participate in this preparatory work. International, governmental and non- governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely with the International Organizatio

20、n for Standardization (ISO) in accordance with conditions determined by agreement between the two organizations. 2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international consensus of opinion on the relevant subjects since each technical commi

21、ttee has representation from all interested IEC National Committees. 3) IEC Publications have the form of recommendations for international use and are accepted by IEC National Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC Publications is

22、 accurate, IEC cannot be held responsible for the way in which they are used or for any misinterpretation by any end user. 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications transparently to the maximum extent possible in their national and r

23、egional publications. Any divergence between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter. 5) IEC provides no marking procedure to indicate its approval and cannot be rendered responsible for any equipment declared to be in confo

24、rmity with an IEC Publication. 6) All users should ensure that they have the latest edition of this publication. 7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and members of its technical committees and IEC National Committees for an

25、y personal injury, property damage or other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC Publications. 8) Attention is drawn to the Normati

26、ve references cited in this publication. Use of the referenced publications is indispensable for the correct application of this publication. 9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent rights. IEC shall not be held responsi

27、ble for identifying any or all such patent rights. International Standard IEC 61047 has been prepared by subcommittee 34C: Auxiliaries for lamps, of IEC technical committee 34: Lamps and related equipment. This second edition of IEC 61047 cancels and replaces the first edition published in 1991, its

28、 Amendment 1 (1996) and Amendment 2 (2001). This second edition constitutes a technical revision. The first edition needed to be revised completely after the decision to delete all EMC-related requirements, given that EMC varies from region to region. This standard may only be used and printed by ap

29、proved subscription and freemailing clients of the SABS.61047 IEC:2004 7 The text of this standard is based on the following documents: FDIS Report on voting 34C/635/FDIS 34C/643/RVD Full information on the voting for the approval of this standard can be found in the report on voting indicated in th

30、e above table. This standard is to be read in conjunction with IEC 61347-1 and IEC 61347-2-2. This publication has been drafted in accordance with the ISO/IEC Directives, Part 2. In this standard, the following print types are used: requirements proper: in roman type; test specifications: in italic

31、type; notes: in smaller roman type. The committee has decided that the contents of this publication will remain unchanged until the maintenance result date indicated on the IEC web site under “http:/webstore.iec.ch“ in the data related to the specific publication. At this date, the publication will

32、be reconfirmed; withdrawn; replaced by a revised edition, or amended. This standard may only be used and printed by approved subscription and freemailing clients of the SABS.61047 IEC:2004 9 INTRODUCTION This International Standard covers performance requirements for electronic step-down convertors

33、for d.c. supplies up to 250 V and a.c. supplies up to 1 000 V at 50 Hz or 60 Hz, operating with controlled voltage filament lamps at frequencies deviating from the supply frequency. Attention is drawn to the fact that operating frequencies below 20 kHz may cause audio noise. NOTE CISPR requirements

34、regarding radio interference have to be observed in some countries. In order to obtain satisfactory performance of filament lamps and electronic convertors, it is necessary that certain features of their designs be properly coordinated. This standard may only be used and printed by approved subscrip

35、tion and freemailing clients of the SABS.This page is intentionally left blankThis standard may only be used and printed by approved subscription and freemailing clients of the SABS.61047 IEC:2004 11 DC OR AC SUPPLIED ELECTRONIC STEP-DOWN CONVERTORS FOR FILAMENT LAMPS PERFORMANCE REQUIREMENTS 1 Scop

36、e This International Standard specifies performance requirements for electronic step-down convertors for use on d.c. supplies up to 250 V and a.c. supplies up to 1 000 V at 50 Hz or 60 Hz with operating frequencies deviating from the supply frequency, associated with tungsten halogen lamps as specif

37、ied in IEC 60357 and other filament lamps. NOTE 1 The tests in this standard are type tests. Requirements for testing individual convertors during production are not included. NOTE 2 Requirements for convertors which incorporate means for varying the lamp power are under consideration. NOTE 3 It may

38、 be expected that convertors complying with this standard will ensure satisfactory operation between 92 % and 106 % of rated supply voltage of filament lamps with rated lives greater than 200 h and rated voltage less than 50 V. NOTE 4 There exist regional standards regarding the regulation of mains

39、current harmonics for end-products such as luminaires and independent control gear. In a luminaire, the control gear is dominant in this respect. Control gear, together with other components, should comply with these standards. 2 Normative references The following referenced documents are indispensa

40、ble for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. IEC 60357, Tungsten halogen lamps (non-vehicle) Performance specifications IEC 61347-1, Lamp contr

41、olgear Part 1: General and safety requirements IEC 61347-2-2, Lamp controlgear Part 2-2: Particular requirements for d.c. or a.c. supplied electronic step-down convertors for filament lamps 3 Terms and definitions For the purposes of this document the following terms and definitions apply. 3.1 total

42、 circuit power the total power dissipated by convertor and lamp(s) in combination, at rated supply voltage of the convertor and at the highest rated output load This standard may only be used and printed by approved subscription and freemailing clients of the SABS.61047 IEC:2004 13 3.2 circuit power

43、 factor the ratio of measured circuit power to the product of the supply voltage (r.m.s.) and the supply current (r.m.s.) 3.3 high power factor convertor a convertor having a circuit power factor of at least 0,85 NOTE 1 For North America a high power factor is defined as a power factor of at least 0

44、,9. NOTE 2 The value of the power factor takes into account the effect of the distortion of the current waveform. 3.4 high audio-frequency impedance convertor a convertor the impedance of which in the frequency range 250 Hz to 2 000 Hz exceeds the values specified in Clause 11 3.5 short-circuit proo

45、f convertor a convertor which remains capable of functioning after an incidental overload or short circuit is removed and after restoration of a protecting device, if any 4 General notes on tests 4.1 The tests according to this standard are type tests. NOTE The requirements and tolerances permitted

46、by this standard are based on testing of a type test sample submitted by the manufacturer for that purpose. In principle this type test sample should consist of units having characteristics typical of the manufacturers production and be as close to the production centre point values as possible. It

47、may be expected with the tolerances given in the standard that products manufactured in accordance with the type test sample will comply with the standard for the majority of the production. Due to the production spread however, it is inevitable that there will sometimes be products outside the spec

48、ified tolerances. For guidance of sampling plans and procedures for inspection by attributes, see IEC 60410. 4.2 For tests which are carried out with a lamp or lamps, this lamp(s) shall fulfill the following requirements. The wattage of the lamp(s) when measured at its rated lamp voltage (d.c. or a.

49、c. 50 Hz/60 Hz) shall not differ from the rated wattage by more than 6 0 +%. 4.3 The tests shall be carried out in the order of the clauses, unless otherwise specified. 4.4 One specimen shall be submitted to all the tests. 4.5 In general all the tests are made on each type of convertor or, where a range of similar convertors is involved for each rated wattage in the range or on a representative selection from the range as a