SANS 60874-1-2007 Connectors for optical fibres and cables Part 1 Generic specification《光纤及电缆连接器 第1部分 总体规范》.pdf

《SANS 60874-1-2007 Connectors for optical fibres and cables Part 1 Generic specification《光纤及电缆连接器 第1部分 总体规范》.pdf》由会员分享，可在线阅读，更多相关《SANS 60874-1-2007 Connectors for optical fibres and cables Part 1 Generic specification《光纤及电缆连接器 第1部分 总体规范》.pdf（33页珍藏版）》请在麦多课文档分享上搜索。

1、 Collection of SANS standards in electronic format (PDF) 1. Copyright This standard is available to staff members of companies that have subscribed to the complete collection of SANS standards in accordance with a formal copyright agreement. This document may reside on a CENTRAL FILE SERVER or INTRA

2、NET SYSTEM only. Unless specific permission has been granted, this document MAY NOT be sent or given to staff members from other companies or organizations. Doing so would constitute a VIOLATION of SABS copyright rules. 2. Indemnity The South African Bureau of Standards accepts no liability for any

3、damage whatsoever than may result from the use of this material or the information contain therein, irrespective of the cause and quantum thereof. ISBN 978-0-626-20202-6 SANS 60874-1:2007Edition 3IEC 60874-1:2006Edition 5SOUTH AFRICAN NATIONAL STANDARD Connectors for optical fibres and cables Part 1

4、: Generic specification This national standard is the identical implementation of IEC 60874-1:2006 and is adopted with the permission of the International Electrotechnical Commission. Published by Standards South Africa 1 dr lategan road groenkloof private bag x191 pretoria 0001 tel: 012 428 7911 fa

5、x: 012 344 1568 international code + 27 12 www.stansa.co.za Standards South Africa SANS 60874-1:2007 Edition 3 IEC 60874-1:2006 Edition 5 Table of changes Change No. Date Scope National foreword This South African standard was approved by National Committee StanSA SC 74A, Communication technology Fi

6、bre optics, in accordance with procedures of Standards South Africa, in compliance with annex 3 of the WTO/TBT agreement. This SANS document was published in August 2007. This SANS document supersedes SABS IEC 60874-1:1999 (edition 2). NORME INTERNATIONALECEIIECINTERNATIONAL STANDARD 60874-1QC 91000

7、0Cinquime ditionFifth edition2006-10Connecteurs pour fibres et cbles optiques Partie 1: Spcification gnrique Connectors for optical fibres and cables Part 1: Generic specification Pour prix, voir catalogue en vigueur For price, see current catalogue IEC 2006 Droits de reproduction rservs Copyright -

8、 all rights reserved Aucune partie de cette publication ne peut tre reproduite ni utilise sous quelque forme que ce soit et par aucun procd, lectronique ou mcanique, y compris la photocopie et les microfilms, sans laccord crit de lditeur. No part of this publication may be reproduced or utilized in

9、any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from the publisher. International Electrotechnical Commission, 3, rue de Varemb, PO Box 131, CH-1211 Geneva 20, SwitzerlandTelephone: +41 22 919 02 11 Telefax: +41 22 919 03 00 E-m

10、ail: inmailiec.ch Web: www.iec.ch CODE PRIX PRICE CODE U Commission Electrotechnique InternationaleInternational Electrotechnical Commission SANS 60874-1:2007This s tandard may only be used and printed by approved subscription and freemailing clients of the SABS .60874-1 IEC:2006 3 CONTENTS FOREWORD

11、.5 1 Scope.11 2 Normative references11 3 Terms and definitions .13 4 Requirements .19 4.1 Classification.19 4.2 Documentation 27 4.3 Standardization system33 4.4 Design and construction 43 4.5 Quality.43 4.6 Performance43 4.7 Identification and marking43 4.8 Packaging .45 4.9 Storage conditions.45 4

12、.10 Safety45 5 Quality assessment procedures 47 5.1 Primary stage of manufacture 47 5.2 Structurally similar components .47 5.3 Qualification approval procedures 49 5.4 Quality conformance inspection .51 5.5 Certified records of released lots .55 5.6 Delayed deliveries .55 5.7 Delivery release befor

13、e completion of group B tests .55 5.8 Alternative test methods 57 5.9 Unchecked parameters57 Bibliography59 Figure 1 Standardization structure 41 Table 1 Example of a typical connector set classification 21 Table 2 Three-level specification structure29 Table 3 - Standards interlink matrix .41 SANS 6

14、0874-1:2007This s tandard may only be used and printed by approved subscription and freemailing clients of the SABS .60874-1 IEC:2006 5 INTERNATIONAL ELECTROTECHNICAL COMMISSION _ CONNECTORS FOR OPTICAL FIBRES AND CABLES Part 1: Generic specification FOREWORD 1) The International Electrotechnical Co

15、mmission (IEC) is a worldwide organization for standardization comprising all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international co-operation on all questions concerning standardization in the electrical and electronic fields. To this end an

16、d in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committe

17、e interested in the subject dealt with may participate in this preparatory work. International, governmental and non-governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for Standardization (ISO) in accord

18、ance with conditions determined by agreement between the two organizations. 2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international consensus of opinion on the relevant subjects since each technical committee has representation from all inte

19、rested IEC National Committees. 3) IEC Publications have the form of recommendations for international use and are accepted by IEC National Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC Publications is accurate, IEC cannot be held respons

20、ible for the way in which they are used or for any misinterpretation by any end user. 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications transparently to the maximum extent possible in their national and regional publications. Any divergence

21、between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter. 5) IEC provides no marking procedure to indicate its approval and cannot be rendered responsible for any equipment declared to be in conformity with an IEC Publication. 6) All

22、 users should ensure that they have the latest edition of this publication. 7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and members of its technical committees and IEC National Committees for any personal injury, property damage or

23、 other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC Publications. 8) Attention is drawn to the Normative references cited in this publicati

24、on. Use of the referenced publications is indispensable for the correct application of this publication. 9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent rights. IEC shall not be held responsible for identifying any or all such p

25、atent rights. International Standard IEC 60874-1 has been prepared by subcommittee 86B: Fibre optic interconnecting devices and passive components, of IEC technical committee 86: Fibre optics. This fifth edition cancels and replaces the fourth edition published in 1999, and constitutes a technical r

26、evision. The specific technical changes from the previous edition include the introduction of new expressions for intermateability and performance, of optical performance standards into the standardization system, and updating the normative references. SANS 60874-1:2007This s tandard may only be use

27、d and printed by approved subscription and freemailing clients of the SABS .60874-1 IEC:2006 7 The text of this standard is based on the following documents: FDIS Report on voting 86B/2370/FDIS 86B/2412/RVD Full information on the voting for the approval of this standard can be found in the report o

28、n voting indicated in the above table. This publication has been drafted in accordance with the ISO/IEC Directives, Part 2. The QC number that appears on the front cover of this publication is the specification number in the IEC Quality Assessment System for Electronic Components (IECQ). IEC 60874 c

29、onsists of the following parts, under the general title Connectors for optical fibres and cables: Part 1: Generic specification Part 1-1: Blank detail specification Environmental categories Part 10-1: Detail specification for fibre optic connector type BFOC/2,5 terminated to multimode fibre type A1

30、Part 10-2: Detail specification for fibre optic connector type BFOC/2,5 terminated to single-mode fibre type B1 Part 10-3: Detail specification for fibre optic adaptor type BFOC/2,5 for single and multimode fibre Part 14-1: Detail specification for fibre optic connector type SC/PC standard terminate

31、d to multimode fibre type A1a, A1b Part 14-2: Detail specification for fibre optic connector type SC/PC tuned terminated to single-mode fibre type B1 Part 14-3: Detail specification for fibre optic adaptor (simplex) type SC for single-mode fibre Part 14-4: Detail specification for fibre optic adapto

32、r (simplex) type SC for multi-mode fibre Part 14-5: Detail specification for fibre optic connector type SC-PC untuned terminated to single-mode fibre type B1 Part 14-6: Detail specification for fibre optic connector - Type SC-APC 9 untuned terminated to single-mode fibre Type B1 Part 14-7: Detail sp

33、ecification for fibre optic connector type SC-APC 9 tuned terminated to single-mode fibre Type B1 Part 14-9: Fibre optic connector type SC-APC tuned 8 terminated on single mode fibre type B1 Detail specification Part 14-10: Fibre optic pigtail or patch cord connector type SC-APC untuned 8 terminated

34、 on single mode fibre type B1 Detail specification Part 17: Sectional specification for fibre optic connector Type F-05 (friction lock) Part 19: Sectional specification for fibre optic connector - Type SC-D(uplex) SANS 60874-1:2007This s tandard may only be used and printed by approved subscription

35、and freemailing clients of the SABS .60874-1 IEC:2006 9 Part 19-1: Fibre optic patch cord connector type SC-PC (floating duplex) standard terminated on multimode fibre type A1a, A1b Detail specification Part 19-2: Fibre optic adaptor (duplex) type SC for single-mode fibre connectors Detail specifica

36、tion Part 19-3: Fibre optic adaptor (duplex) type SC for multimode fibre connectors Detail specification The committee has decided that the contents of this publication will remain unchanged until the maintenance result date indicated on the IEC web site under “http:/webstore.iec.ch“ in the data rel

37、ated to the specific publication. At this date, the publication will be reconfirmed; withdrawn; replaced by a revised edition, or amended. SANS 60874-1:2007This s tandard may only be used and printed by approved subscription and freemailing clients of the SABS .60874-1 IEC:2006 11 CONNECTORS FOR OPT

38、ICAL FIBRES AND CABLES Part 1: Generic specification 1 Scope This part of IEC 60874 applies to fibre optic connectors sets and individual components (i.e. adaptors, plugs, sockets) for all types, sizes and structures of fibres and cables. It includes: connector set requirements; quality assessment p

39、rocedures. This part of IEC 60874 is divided into five clauses: Clauses 1 (Scope), 2 (Normative references) and 3 (Terms and definitions) contain general information pertaining to this generic specification; Clause 4 (Requirements) contains all the requirements to be met by connectors covered by thi

40、s specification. This includes requirements for classification, the IEC specification system, documentation, materials, workmanship, quality, performance, identification, and packaging; Clause 5 (Quality assessment procedures) contains all of the procedures that must be followed for IEC quality asse

41、ssment of products covered by this standard. NOTE 1 Clauses 1 to 4 are applicable generally and refer to all connector standards while Clause 5 relates to IEC qualification alone. NOTE 2 This part of IEC 60874 applies also to the connectors covered by IEC 61753, IEC 61754, and IEC 61755 series. This

42、 standard does not cover test and measurement procedures, which are described in IEC 61300-1, IEC 61300-2 and IEC 61300-3. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undat

43、ed references, the latest edition of the referenced document (including any amendments) applies. IECQ 001002-2:1998, IEC Quality Assessment System for Electronic Components (IECQ) Rules of procedure Part 2: Documentation IECQ 001002-3:2005, IEC Quality Assessment System for Electronic Components (IE

44、CQ) Rules of procedure Part 3: Approval procedures IEC 60027 (all parts), Letter symbols to be used in electrical technology IEC 60050-731, International Electrotechnical Vocabulary (IEV) Chapter 731: Optical fibre communication IEC 60410, Sampling plans and procedures for inspection by attributes S

45、ANS 60874-1:2007This s tandard may only be used and printed by approved subscription and freemailing clients of the SABS .60874-1 IEC:2006 13 IEC 60617, Graphical symbols for diagrams IEC 60695-11-5, Fire hazard testing Part 11-5: Test flames Needle-flame test method Apparatus, confirmatory test arr

46、angement and guidance IEC 60825-1, Safety of laser products Part 1: Equipment classification, requirements and users guide IEC 61300 (all parts), Fibre optic interconnecting devices and passive components Basic test and measurement procedures IEC 61753-1: Fibre optic interconnecting devices and pass

47、ive components Part 1: General and guidance for performance standards1) IEC 61754 (all parts), Fibre optic connector interfaces IEC 61755 (all parts), Fibre optic connector optical interfaces IEC 61930, Fibre optic graphic symbology IEC 61931, Fibre optic terminology ISO 129, Technical drawings Indi

48、cation of dimensions and tolerances Part 1: General principles ISO 286-1, ISO system of limits and fits Part 1: Bases of tolerances, deviations and fits ISO 370:1975, Toleranced dimensions Conversion from inches into millimetres and vice versa ISO 1101, Geometrical product specifications Technical d

49、rawings Geometrical tolerancing Tolerances of form, orientation, location and run-out ISO 8601, Data elements and interchange formats Information interchange Representation of dates and times 3 Terms and definitions For the purposes of this part of IEC 60874, the definitions contained in IEC 60050(731) and IEC 61931, as well as the following definitions, apply. 3.1 adaptor a component in which