SAE J 2862-2015 User-s Manual for the Small Adult Female Hybrid III Test Dummy.pdf
《SAE J 2862-2015 User-s Manual for the Small Adult Female Hybrid III Test Dummy.pdf》由会员分享,可在线阅读,更多相关《SAE J 2862-2015 User-s Manual for the Small Adult Female Hybrid III Test Dummy.pdf(73页珍藏版)》请在麦多课文档分享上搜索。
1、 SURFACE VEHICLE INFORMATION REPORT J2862 FEB2015 Issued 2015-02 Users Manual for the Small Adult Female Hybrid III Test Dummy RATIONALE SAE J2862 replaced EA-25 in 2015. In addition to the format change and the correction of typographical and grammatical errors, the following changes were made to t
2、his Information Report: References to SAE J211 were changed to J211-1 throughout the report Joint adjustment changed from “1 2 G” to “1 G suspended adjustment” throughout the report Section 1 SCOPE added Section 2 REFERENCES added “SAE J211-1 Instrumentation for Impact Test Part 1 Electronic Instrum
3、entation” Section 2 REFERENCES added “SAE J2517 Hybrid III Family Chest Potentiometer Calibration” Section 2 REFERENCES added “SAE J2878 Low Speed Thorax Impact Test Procedure for the HIII 5th Dummy” Section 2 REFERENCES added “SAE J2915 H-III5F Spine Box Update to Eliminate Noise” Section 2 REFEREN
4、CES added “SAE J2921 H-III5F Chest Jacket Harmonization” Section 2 REFERENCES added “Banglmaier, R.F., Pecararo, K.M., Feustel, J.R., Scherer, R.D. and Rouhana, S.W., 2005, “Development and evaluation of a Proposed Neck Shield for a 5thPercentile Hybrid III Dummy,” Stapp Car Crash Journal, vol. 49.”
5、 Section 3 DEFINITIONS AND ABBREVIATIONS and throughout the document changed “Calibration Test” to “Certification Test” for all tests that are conducted for the purpose of assuring that the dummy responds within the specifications outlined in this document Section 4 PART NUMBERS updated source for 4
6、9 CFR, Part 572, Subpart O drawings Section 7 DISASSEMBLY AND REASSEMBLY PROCEDURES added “TABLE 1 TORQUE SPECIFICATIONS” and indexed all other table numbers accordingly. Section 7 DISASSEMBLY AND REASSEMBLY PROCEDURES changed “sternum bib” to “bib assembly” for consistency with 49 CFR, Part 572, Su
7、bpart O parts list Section 7.3 Head corrected the part number of the head skin Section 7.4 Neck changed the description of part number 180-2004 from “neck cable insert, upper” to “neck bushing, upper” and changed the description of part number 180-2005 from “neck cable insert, lower” to “neck bushin
8、g, lower” for consistency with 49 CFR, Part 572, Subpart O parts list _ SAE Technical Standards Board Rules provide that: “This report is published by SAE to advance the state of technical and engineering sciences. The use of this report is entirely voluntary, and its applicability and suitability f
9、or any particular use, including any patent infringement arising therefrom, is the sole responsibility of the user.” SAE reviews each technical report at least every five years at which time it may be revised, reaffirmed, stabilized, or cancelled. SAE invites your written comments and suggestions. C
10、opyright 2015 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMEN
11、T ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org SAE values your input. To provide feedback on this Technical Report, please visit http:/www.sae.org/technical/standards/J2862_20150
12、2 SAE INTERNATIONAL J2862 Issued FEB2015 Page 2 of 73 Section 7.4 Neck changed the description of part number 880105-255 from “molded rubber neck” to “neck molded assembly” for consistency with 49 CFR, Part 572, Subpart O parts list Section 7.5 Upper Torso changed the description of part number 8801
13、05-1000 from “spine weldment” to “thoracic spine weldment” for consistency with 49 CFR, Part 572, Subpart O parts list Section 7.5 Upper Torso changed the description of part number 880105-323 from “behind rib strips” to “front rib end, threaded” for consistency with 49 CFR, Part 572, Subpart O part
14、s list Section 7.5 Upper Torso changed the description of part number 880105-324 from “stiffener strip” to “front rib end stiffener” for consistency with 49 CFR, Part 572, Subpart O parts list Section 7.5 Upper Torso changed the description of part number 880105-340 from “nut” to “clavicle link pivo
15、t nut” for consistency with 49 CFR, Part 572, Subpart O parts list Section 7.5 Upper Torso changed the description of part number 880105-342 from “clavicle link washer” to “”clavicle link pivot washer (Delrin)” for consistency with the NHTSA PADI, dated June 10, 2002 Section 7.5 Upper Torso changed
16、the description of part number 880105-359 from “washer sternum” to “”clavicle link pivot washer (Urethane)”for consistency with the NHTSA PADI, dated June 10, 2002 Section 7.5 Upper Torso changed the description of part numbers 880105-380left, -381right from “shoulders” to “shoulder assembly” for co
17、nsistency with 49 CFR, Part 572, Subpart O parts list Section 7.5 Upper Torso corrected the part number of the rib set Section 7.5 Upper Torso changed the description of part number 880105-1085 from “adaptor assembly” to “adaptor assembly lumbar thoracic” for consistency with 49 CFR, Part 572, Subpa
18、rt O parts list Section 7.5 Upper Torso changed the description of part number 8801205-1080 from “chest transducer assembly” to “chest deflection transducer assembly” for consistency with 49 CFR, Part 572, Subpart O parts list Section 7.5.1 Upper Torso Disassembly changed “one G adjustment” to “1 G
19、suspended setting” Section 7.5.2 Upper Torso Reassembly added directions to re-tighten the SHCS to eliminate mechanical noise caused by slippage between the spine mounting assembly and the load cell simulator Section 7.6 Chest Deflection Transducer corrected the part numbers of the molded stop assem
20、bly, chest accelerometer mount, and chest potentiometer for consistency with 49 CFR, Part 572, Subpart O parts list Section 7.6 Chest Deflection Transducer changed the description of part number 880105-328 from “thoracic spine load cell structural replacement” to “thoracic spine load cell simulator”
21、 for consistency with 49 CFR, Part 572, Subpart O parts list Section 7.6 Chest Deflection Transducer changed the description of part number SA572-S51 from “potentiometer” to “chest potentiometer” for consistency with 49 CFR, Part 572, Subpart O parts list Section 7.6.1 Chest Deflection Transducer Di
22、sassembly Added “Once calibrated according to J2715, “Hybrid III Family Chest Potentiometer Calibration Procedure” the chest potentiometer assembly consisting of the transducer arm assembly (Item 5, Figure 13), chest potentiometer (Item 12, Figure 13), potentiometer bracket (Item 13, Figure 13) and
23、arm connector (Item 14, Figure 13) should not be mechanically adjusted or further disassembled.” Section 7.7 Clavicle changed description of part number 880105-344 from “shoulder pivot stop assembly” to “rubber stop assembly” for consistency with 49 CFR, Part 572, Subpart O parts list Section 7.7 Cl
24、avicle changed description of part number 880105-348 from “shoulder bushing” to “shoulder yoke pivot bushing” for consistency with 49 CFR, Part 572, Subpart O parts list SAE INTERNATIONAL J2862 Issued FEB2015 Page 3 of 73 Section 7.7 Clavicle changed description of part number 880105-349 from “yoke
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- SAEJ28622015USERSMANUALFORTHESMALLADULTFEMALEHYBRIDIIITESTDUMMYPDF

链接地址:http://www.mydoc123.com/p-1027655.html