SAE AS 81044 5A-2011 WIRE ELECTRIC CROSSLINKED POLYALKENE INSULATED SILVER-COATED COPPER NORMAL WEIGHT 600-VOLT 150 《600 V 150℃正常重量的交联聚烯烃绝缘镀银铜电线》.pdf

《SAE AS 81044 5A-2011 WIRE ELECTRIC CROSSLINKED POLYALKENE INSULATED SILVER-COATED COPPER NORMAL WEIGHT 600-VOLT 150 《600 V 150℃正常重量的交联聚烯烃绝缘镀银铜电线》.pdf》由会员分享，可在线阅读，更多相关《SAE AS 81044 5A-2011 WIRE ELECTRIC CROSSLINKED POLYALKENE INSULATED SILVER-COATED COPPER NORMAL WEIGHT 600-VOLT 150 《600 V 150℃正常重量的交联聚烯烃绝缘镀银铜电线》.pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、 AEROSPACE STANDARD WIRE, ELECTRIC, CROSSLINKED POLYALKENE INSULATED, SILVER-COATED COPPER, NORMAL WEIGHT, 600-VOLT, 150C AS81044/5Copyright 2016 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any m

2、eans, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org

3、 ISSUED2000-04 REVISED2007-11 REAFFIRMED2016-05 THIRD ANGLE PROJECTION CUSTODIAN: AE-8D REV.A FEDERAL SUPPLY CLASS 6145 AS81044/5 SHEET 1 OF 3 REV. A PROCUREMENT SPECIFICATION: AS81044 SAE Technical StandardsBoardRulesprovidethat:“ThisreportispublishedbySAE toadvancethestateoftechnicalandengineering

4、 sciences. The use of thisreport isentirelyvoluntary, andits applicability andsuitability for any particularuse, includingany patent infringement arising therefrom,is the soleresponsibility of theuser.”SAE reviewseachtechnical reportatleasteveryfiveyearsatwhichtimeitmayberevised,reaffirmed,stabilize

5、d,orcancelled. SAEinvites yourwritten comments andsuggestions.SAE values your input. To provide feedback on this Technical Report, please visit http:/www.sae.org/technical/standards/AS81044/5A RATIONALE AS81044/5A HAS BEEN REAFFIRMED TO COMPLY WITH THE SAE FIVE-YEAR REVIEW POLICY. NOTICE THE COMPLET

6、E REQUIREMENTS FOR PROCURING THE WIRE DESCRIBED HEREIN SHALL CONSIST OF THIS DOCUMENT AND THE ISSUE IN EFFECT OF SPECIFICATION AS81044. INACTIVE FOR NEW DESIGN IN AIRCRAFT APPLICATIONS AFTER DATE OF ISSUE. USE AS81044/6. FIGURE 1 AS81044/5 CONSTRUCTION AEROSPACE STANDARD AS81044/5 SHEET 2 OF 3 REV.

7、A WIRE, ELECTRIC, CROSSLINKED POLYALKENE INSULATED, SILVER-COATED COPPER, NORMAL WEIGHT, 600-VOLT, 150C TABLE 1 CONSTRUCTION DETAILS PART NO. 1/ WIRE SIZE STRANDING (NUMBER OF STRANDS X AWG GAGE OF STRANDS) DIAMETER OF STRANDED CONDUCTOR (INCHES) FINISHED WIRE JACKET THICKNESS (INCHES) (MIN) (MAX) R

8、ESISTANCE AT 20 C (68 F) (OHMS/1000 FT). (MAX) DIAMETER (INCHES) WEIGHT (LBS/1000 FT) (NOM) 2/ (MAX) M81044/5-24-* 24 19 X 36 .023 .025 24.3 .057 .002 2.8 3.0 .005 .001 M81044/5-22-* 22 19 X 34 .029 .032 15.1 .069 .003 4.1 4.3 .005 .001 M81044/5-20-* 20 19 X 32 .037 .040 9.19 .078 .003 5.8 6.1 .005

9、.001 M81044/5-18-* 18 19 X 30 .046 .050 5.79 .088 .003 8.3 8.7 .005 .001 M81044/5-16-* 16 19 X 29 .052 .057 4.52 .097 .004 10.3 10.9 .005 .001 M81044/5-14-* 14 19 X 27 .065 .072 2.88 .115 .004 15.5 16.2 .005 .001 M81044/5-12-* 12 37 X 28 .084 .089 1.90 .131 .004 23.0 24.2 .005 .001 M81044/5-10-* 10

10、37 X 26 .106 .112 1.19 .161 .005 35.3 36.5 .005 .001 M81044/5-8-* 8 133 X 29 .158 .169 .658 .219 .006 64.8 68.3 .005 .001 M81044/5-6-* 6 133 X 27 .198 .213 .418 .269 .007 99.2 108. .005 .001 M81044/5-4-* 4 133 X 25 .250 .268 .264 .325 .008 158. 166. .005 .001 M81044/5-2-* 2 665 X 30 .320 .340 .170 .

11、404 .012 244. 265. .010 .002 M81044/5-0-* 0 1045 X 30 .405 .425 .108 .494 .016 370. 399. .010 .002 1/ PART NO.: THE ASTERISKS IN THE PART NUMBER COLUMN, TABLES 1 AND 2, SHALL BE REPLACED BY COLOR CODE DESIGNATORS IN ACCORDANCE WITH MIL-STD-681. EXAMPLES: SIZE 20, WHITE M81044/5-20-9; WHITE WITH ORAN

12、GE STRIPE M81044/5-20-93 2/ NOMINAL VALUES ARE FOR INFORMATION ONLY. NOMINAL VALUES ARE NOT REQUIREMENTS. TABLE 2 PERFORMANCE DETAILS PART NO. ABRASION RESISTANCE (PROCEDURE I) BEND TESTING MANDREL DIAMETER (INCHES) (3%) TEST LOAD (LBS) (3%) RESISTANCE (INCHES OF TAPE) (MIN) (INITIAL AND AFTER IMMER

13、SION) WEIGHT SUPPORT BRACKET WEIGHT (LBS) TENSION LOAD (LBS) LIFE CYCLE TEST AND ACCELERATED AGING TEST 1/COLD BEND TEST WRAP TEST LIFE CYCLE TEST AND ACCELERATED AGING TEST 1/ COLD BEND TESTM81044/5-24-* 12 A 1.0 1.0 .50 1.0 .250 1.0 3.0 M81044/5-22-* 22 A 1.0 1.0 .75 1.0 .250 3.0 3.0 M81044/5-20-*

14、 22 A 1.0 1.0 .75 1.0 .250 4.0 4.0 M81044/5-18-* 22 A 1.0 1.0 1.00 1.5 .375 4.0 4.0 M81044/5-16-* 30 A 1.0 2.0 1.00 1.5 .375 5.0 5.0 M81044/5-14-* 13 B 3.0 2.0 1.50 2.0 .500 5.0 5.0 M81044/5-12-* 17 B 3.0 2.0 2.0 2.0 .500 5.0 5.0 M81044/5-10-* 20 B 3.0 3.0 3.0 3.0 .750 5.0 5.0 M81044/5-8-* 25 B 3.0

15、3.0 3.0 4.0 .750 6.0 6.0 M81044/5-6-* 25 C 3.0 4.0 4.0 5.0 1.00 6.0 10.0 M81044/5-4-* 33 C 4.25 4.0 5.0 6.0 1.25 6.0 10.0 M81044/5-2-* 34 C 4.25 5.0 6.0 8.0 3.00 6.0 15.0 M81044/5-0-* 48 C 4.25 5.0 8.0 10.0 4.00 7.0 15.0 1/ ALSO FOR BEND TESTS AFTER IMMERSION. AEROSPACE STANDARD AS81044/5 SHEET 3 OF

16、 3 REV. A WIRE, ELECTRIC, CROSSLINKED POLYALKENE INSULATED, SILVER-COATED COPPER, NORMAL WEIGHT, 600-VOLT, 150C WIRE RATINGS AND ADDITIONAL REQUIREMENTS TEMPERATURE RATING: 150 C (302 F) MAX CONDUCTOR TEMPERATURE VOLTAGE RATING: 600 VOLTS (RMS) AT SEA LEVEL THIS INSULATION SYSTEM HAS BEEN USED IN AE

17、ROSPACE APPLICATIONS USING 115 VOLTS (PHASE TO NEUTRAL), 400 HERTZ AC AND 28 VOLTS DC. VERIFICATION OF THE SUITABILITY OF THIS PRODUCT FOR USE IN OTHER ELECTRICAL SYSTEM CONFIGURATIONS IS THE RESPONSIBILITY OF THE USER. ACCELERATED AGING: OVEN TEMPERATURE, 300 2 C (572 3.6 F) FOR 6 HOURS; FOR IDENTI

18、FICATION LEGIBILITY, 225 2 C (437 3.6 F) FOR 6 HOURS BLOCKING: 225 2 C (437 3.6 F) COLOR: IN ACCORDANCE WITH MIL-STD-104, CLASS 1; WHITE PREFERRED FLAMMABILITY: 30 SECONDS (MAX); 3.0 INCHES (MAX); NO FLAMING OF TISSUE PAPER HUMIDITY RESISTANCE: 5000 MEGOHMS FOR 1000 FT, MIN INSULATION RESISTANCE AFT

19、ER HUMIDITY EXPOSURE IDENTIFICATION, STRIPING, OR BANDING DURABILITY: 125 CYCLES (250 STROKES) (MIN), 500 GRAMS WEIGHT IMPULSE DIELECTRIC TEST: PRIMARY INSULATION (WHEN TEST IS USED IN LIEU OF SPARK TEST): 6.0 KILOVOLTS (PEAK), 100% TEST FINISHED WIRE: 8.0 KILOVOLTS (PEAK), 100% TEST INSULATION RESI

20、STANCE: 5000 MEGOHMS FOR 1000 FT (MIN) LIFE CYCLE: OVEN TEMPERATURE, 200 2 C (392 3.6 F) FOR 168 HOURS PHYSICAL PROPERTIES OF PRIMARY INSULATION (PULLED AT 2 INCHES PER MINUTE): TENSILE STRENGTH, 2500 PSI (MIN) FOR SIZES 24 THROUGH 12 2000 PSI (MIN) FOR SIZES 10 THROUGH 0 ELONGATION, 150% (MIN), ALL

21、 SIZES POLYIMIDE CURE TEST: NOT APPLICABLE PROPELLANT RESISTANCE: TEST REQUIRED SHRINKAGE: SIZES 24 THROUGH 12: 0.125 INCH MAX AT 300 2 C (572 3.6 F) SIZES 10 THROUGH 0: 0.250 INCH MAX AT 300 2 C (572 3.6 F) SMOKE: 200 2 C (392 3.6 F) SPARK TEST OF PRIMARY INSULATION: 3000 VOLTS (RMS), 60HZ, 100% TE

22、ST SURFACE RESISTANCE: 500 MEGOHMS-INCHES (MIN), INITIAL AND FINAL READINGS THERMAL SHOCK: OVEN TEMPERATURE 150 2 C (302 3.6 F) MAX CHANGE IN MEASUREMENT: 0.060 INCH WET DIELECTRIC TEST: 2500 VOLTS (RMS) WICKING: 2.25 INCHES (MAX) WRAP TEST: MANDREL WRAP TEST REQUIRED A CHANGE BAR (|) LOCATED IN THE

23、 LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY.