SAE AS 625C-2001 HOSE ASSEMBLY 3000 psi PTFE FLARELESS 45 O 90 HEAVYWEIGHT《抗拉强度3000psi的重型45对90聚四氟乙烯(PTFE)非扩口软管组件》.pdf

《SAE AS 625C-2001 HOSE ASSEMBLY 3000 psi PTFE FLARELESS 45 O 90 HEAVYWEIGHT《抗拉强度3000psi的重型45对90聚四氟乙烯(PTFE)非扩口软管组件》.pdf》由会员分享，可在线阅读，更多相关《SAE AS 625C-2001 HOSE ASSEMBLY 3000 psi PTFE FLARELESS 45 O 90 HEAVYWEIGHT《抗拉强度3000psi的重型45对90聚四氟乙烯(PTFE)非扩口软管组件》.pdf（6页珍藏版）》请在麦多课文档分享上搜索。

1、AEROSPACE STANDARD HOSE ASSEMBLY, 3000 psi, PTFE, FLARELESS, 45 TO 90, HEAVYWEIGHTAS625Copyright 2013 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying,

2、recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org ISSUED 1984-07REVISED 2001-05 REAFFIRMED 20

3、13-01THIRD ANGLE PROJECTION CUSTODIAN: G-3/G-3D REV.CFEDERAL SUPPLY CLASS 4720 AS625SHEET 1 OF 6REV. CPROCUREMENT SPECIFICATION: AS604 /2/SAE Technical Standards Board Rules provide that: “This report ispublishedby SAE toadvance thestate of technicalandengineeringsciences.The useofthis reportisentir

4、elyvoluntary, andits applicability and suitability forany particular use,including any patent infringement arising therefrom, isthe soleresponsibilityofthe user.”SAE reviews eachtechnicalreport at least every five years at which time itmay berevised,reaffirmed, stabilized, orcancelled. SAE invites y

5、ourwrittencomments andsuggestions. SAE values your input. To provide feedbackon this Technical Report, please visit http:/www.sae.org/technical/standards/AS625CRATIONALE AS625C HAS BEEN REAFFIRMED TO COMPLY WITH THE SAE FIVE-YEAR REVIEW POLICY. AEROSPACE STANDARD AS625SHEET 2 OF 6REV.CHOSE ASSEMBLY,

6、 3000 psi, PTFE, FLARELESS, 45 TO 90, HEAVYWEIGHTAEROSPACE STANDARD AS625SHEET 3 OF 6REV.CHOSE ASSEMBLY, 3000 psi, PTFE, FLARELESS, 45 TO 90, HEAVYWEIGHTAEROSPACE STANDARD AS625SHEET 4 OF 6REV.CHOSE ASSEMBLY, 3000 psi, PTFE, FLARELESS, 45 TO 90, HEAVYWEIGHTAEROSPACE STANDARD AS625 SHEET 5 OF 6 REV.C

7、 HOSE ASSEMBLY, 3000 psi, PTFE, FLARELESS, 45 TO 90, HEAVYWEIGHT NOTES:1. MATERIALS:a. HOSE AND FITTINGS PER AS604b. SLEEVES - SEE APPLICABLE STANDARD PER TABLE 2/2/ THIS HOSE ASSEMBLY SHALL BE QUALIFIED IN ACCORDANCE WITH PROCUREMENT SPECIFICATION AS604. USERS OF THIS STANDARD ARE ADVISED TO CONTRO

8、L SOURCE APPROVAL(S) BY STANDARD PAGE SUPPLEMENT SHEET OR SIMILAR MEANS.CHANGE-OVER FROM USER-QPL TO PRI-QPL SHALL BE PERFORMED IN ACCORDANCE WITH AS604D, AND COMPLETED WITHIN 6 MONTHS FROM THE DATE OF ISSUE OF PRI-QPL-AS604. USERS OF THIS STANDARD SHALL PROCURE THE PRODUCT FROM ACCREDITED MANUFACTU

9、RERS, OR THEIR ACCREDITED DISTRIBUTORS, AS LISTED IN THE PERFORMANCE REVIEW INSTITUTE (PRI) QUALIFIED PRODUCTS LIST OF PRI-QPL-AS604 FOR THIS STANDARD.3. MARKING SHALL BE PER AS604 ON A STAINLESS STEEL BAND NOT OVER 1.0 in WIDE, OR ON THE COLLAR. THE CHARACTERS SHALL BE A MINIMUM OF .06 in HIGH. THE

10、 BAND SHALL BE SO DESIGNED AS TO REMAIN TIGHT ON THE HOSE TO PREVENT RELATIVE MOVEMENT AND RESULTANT CHAFING. IT SHALL BE OF SUFFICIENT STRENGTH TO PREVENT REMOVAL BY HAND. HOSE ASSEMBLY DATE AND “PT” SYMBOL SHALL BE PERMANENTLY MARKED ON THE BAND OR ON AN END FITTING OR A FIRESLEEVE CLAMP.4. CONSTR

11、UCTION AND PERFORMANCE PER AS604. FITTINGS SHALL BE PERMANENTLY ATTACHED TO THE HOSE./5/ LENGTH “L” IS A THREE DIGIT NUMBER OF WHICH THE FIRST TWO DIGITS DESCRIBE THE HOSE ASSEMBLY LENGTH IN WHOLE INCHES, AND THE THIRD DIGIT, THE FRACTION OF AN INCH IN EIGHTHS. LENGTH “L” IS MEASURED FROM “GAGE POIN

12、T” TO “GAGE POINT.” FOR LENGTH TOLERANCES SEE TABLE 3./6/ TO CONVERT “GAGE POINT” TO “GAGE POINT” TO “END TO END” MEASUREMENT, ADD “D” TO LENGTH “L”./7/ HOSE ASSEMBLY INSIDE DIAMETER SHALL BE VERIFIED BY PASSING THE DESIGNATED, OR LARGER, SPHERICAL BALL PER TABLE 1 THROUGH THE HOSE ASSEMBLY./8/ DIST

13、ANCE ACROSS CORNERS OF THE COUPLING NUT MAY EXCEED THIS DIMENSION./9/ STANDARD COUPLING NUTS SHALL BE IN ACCORDANCE WITH AS21921 OR AS4370. NONSTANDARD COUPLING NUTS MAY BE USED, PROVIDED THEY ARE DIMENSIONALLY AND FUNCTIONALLY EQUIVALENT, AND PROVIDED THEY CANNOT BE REMOVED FROM THE FITTING./10/ TU

14、BULAR ABRASION (TFE) SLEEVES SHALL HAVE AN ID NO GREATER THAN HOSE OD + .05 in. AXIAL MOVEMENT OF THE SLEEVE INSTALLED ON THE HOSE SHALL NOT EXCEED .05 in. ENDS OF THE TUBULAR SLEEVE SHALL BE TERMINATED WITH A LENGTH OF AMS-DTL-23053/11 (FEP) CLASS 1 OR 2, COLOR CLEAR, PER TABLE 5 AND FIGURE 2./11/

15、COIL ABRASION SLEEVES, WHEN ASSEMBLED ON A STRAIGHT HOSE, SHALL HAVE AN AVERAGE GAP BETWEEN COILS NOT EXCEEDING .05 in. DISPLACEMENT OF THE COILS OF THE SLEEVE, CAUSING A GREATER GAP, SHALL NOT BE CAUSE FOR REJECTION IF THE COILS CAN BE REPOSITIONED TO MEET THE GAP REQUIREMENTS. ENDS OF THE COIL SLE

16、EVE SHALL BE TERMINATED WITH A LENGTH OF HEAT SHRINKABLE SLEEVING IN ACCORDANCE WITH TABLE 5 AND FIGURE 2. CODE “B” (NYLON COIL) ABRASION SLEEVES SHALL BE TERMINATED WITH AMS-DTL-23053/5, CLASS 1 OR 3, COLOR BLACK. CODE “L” (COIL ABRASION) SLEEVES SHALL BE TERMINATED WITH AMS-DTL-23053/12, CLASS I,

17、COLOR TRANSPARENT, PTFE (OPTIONAL AMS-DTL-23053/11 (FEP) CLASS 1 OR 2, COLOR CLEAR)./12/ THE TABLE 2 SLEEVE DIAMETERS FOR AS1072 SLEEVES APPLY WHEN THE SLEEVE IS COMPRESSED, OR CLAMPED, TO CONTACT THE HOSE. IN THIS CASE A WRINKLE MAY OCCUR OVER APPROXIMATELY 10% OF THE SLEEVE CIRCUMFERENCE./13/ THE

18、CUT ENDS OF THE FIRESLEEVE SHALL BE COATED WITH RTV SILICONE RUBBER, PRIOR TO INSTALLATION, TO PREVENT WICKING OF FLUIDS. THE FIRESLEEVE ENDS SHALL BE SECURED TO THE HOSE ASSEMBLY END FITTINGS WITH CORROSION RESISTANT STEEL BANDS. AFTER INSTALLATION, CRACKS OR VOIDS IN THE FIRESLEEVE, WHICH EXPOSE T

19、HE FIBERGLASS, SHALL BE COATED WITH RTV SILICONE RUBBER./14/ DIAMETERS ARE LISTED FOR CLAMP SELECTION. TUBULAR SLEEVES MAY NOT BE A PERFECT ROUND AND SHALL BE MEASURED WITH A DIAMETER TAPE RULER (OFTEN REFERRED TO AS PI-TAPE)./15/ INTEGRAL ABRASION SLEEVE SHALL FORM AN INTEGRAL, PERMANENT PART OF TH

20、E HOSE AND SHALL TERMINATE A MAXIMUM OF .200 in FROM THE END OF THE COLLAR./16/ FEP AND POLYOLEFIN SHRINK ABRASION SLEEVES SHALL BE SHRUNK TO A SNUG FIT OVER THE HOSE AND END FITTING COLLARS./17/ ADD “AS1055 TYPE IIb CLASS A-S/P” OR “AS150 TYPE VIIIbA” TO IDENTIFICATION MARKING TO SHOW LEVEL OF COMPLIANCE, “FIRE RESISTANT” (5 min), WITH AS1055 OR AS150.AEROSPACE STANDARD AS625SHEET 6 OF 6REV.CHOSE ASSEMBLY, 3000 psi, PTFE, FLARELESS, 45 TO 90, HEAVYWEIGHT