SAE AS 6116-2011 Aluminum Fittings Axially Swaged Tube with Flareless Separable Fluid System Up to 1500 psi (10 340 kPa) Maximum Specification for《最大为1500 psi(10 340 kPa)液体系统中使用的带有.pdf
《SAE AS 6116-2011 Aluminum Fittings Axially Swaged Tube with Flareless Separable Fluid System Up to 1500 psi (10 340 kPa) Maximum Specification for《最大为1500 psi(10 340 kPa)液体系统中使用的带有.pdf》由会员分享,可在线阅读,更多相关《SAE AS 6116-2011 Aluminum Fittings Axially Swaged Tube with Flareless Separable Fluid System Up to 1500 psi (10 340 kPa) Maximum Specification for《最大为1500 psi(10 340 kPa)液体系统中使用的带有.pdf(39页珍藏版)》请在麦多课文档分享上搜索。
1、_ SAE Technical Standards Board Rules provide that: “This report is published by SAE to advance the state of technical and engineering sciences. The use of this report is entirely voluntary, and its applicability and suitability for any particular use, including any patent infringement arising there
2、from, is the sole responsibility of the user.” SAE reviews each technical report at least every five years at which time it may be reaffirmed, revised, or cancelled. SAE invites your written comments and suggestions. Copyright 2011 SAE International All rights reserved. No part of this publication m
3、ay be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside U
4、SA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org SAE values your input. To provide feedback on this Technical Report, please visit http:/www.sae.org/technical/standards/AS6116AEROSPACESTANDARDAS6116 Issued 2011-11 Aluminum Fittings, Axially Swaged Tube with Flar
5、eless Separable, Fluid System Up to 1500 psi (10 340 kPa) Maximum, Specification for RATIONALE This specification is being prepared to provide the performance requirements for aluminum axially swaged, field attachable, 1500 psi, tube fittings. 1. SCOPE This SAE Aerospace Standard (AS) establishes th
6、e requirements for externally swaged aluminum tube fittings on aluminum tubing with flareless separable fitting ends for use in hydraulic supply and return aerospace fluid systems including pneumatic, coolants, and fire extinguishers up to a maximum operating pressure of 1500 psig (10 340 kPa) and a
7、 maximum operating temperature range of 65 to +225 F (-54 to +107 C). This specification covers a common aluminum fitting that may be used for a range of operating pressures up to 1500 psi with different tubing materials and tubing wall thicknesses, and is assembled with the same tooling in accordan
8、ce with AS6124. Table 12 shows applicable aerospace fitting part number standard and tubing materials and operating pressures. 2. APPLICABLE DOCUMENTS The following publications form a part of this document to the extent specified herein. The latest issue of SAE publications shall apply. The applica
9、ble issue of other publications shall be the issue in effect on the date of the purchase order. In the event of conflict between the text of this document and references cited herein, the text of this document takes precedence. Nothing in this document, however, supersedes applicable laws and regula
10、tions unless a specific exemption has been obtained. 2.1 SAE Publications Available from SAE, 400 Commonwealth Drive, Warrendale, PA 15096-0001, Tel: 877-606-7323 (inside USA and Canada) or 724-776-4970 (outside USA), www.sae.org.AMS2700 Passivation of Corrosion Resistant Steels AMS-QQ-A-225/8 Alumi
11、num Alloy 6061 Bar, Rod, Wire, and Special Shapes; Rolled, Drawn, or Cold Finished AMS-QQ-A-225/9 Aluminum Alloy 7075 Bar, Rod, Wire, and Special Shapes; Rolled, Drawn, or Cold Finished AMS-QQ-A-225/6 Aluminum Alloy, 2024, Bar, Rod, and Wire; Rolled, Drawn, or Cold Finished AMS4083 Aluminum Alloy Tu
12、bing, Hydraulic, Seamless, Drawn, Round 1.0MG 0.6, .20CR (6061-T6) Solution and Precipitation Heat Treated Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SAE AS6116 Page 2 of 39 AMS4081 Aluminum All
13、oy, Tubing, Hydraulic, Seamless, Drawn, Round, 1.0Mg - 0.60Si - 0.28Cu - 0.20Cr (6061-T4) Solution Heat Treated and Naturally Aged AMS4071 Aluminum Alloy, Drawn, Round, Seamless Hydraulic Tubing, 2.5Mg - 0.25Cr (5052-O), Annealed AMS4070 Aluminum Alloy, Drawn, Round Seamless Tubing, 2.5Mg - 0.25Cr (
14、5052-O), Annealed AMS2477 Conversion Coating for Aluminum Alloys Low Electrical Resistance Coating AS478 Identification Marking Methods AS603 Impulse Testing of Hydraulic Hose, Tubing, and Fitting Assemblies ARP1185 Flexure Testing of Hydraulic Tubing Joints and Fittings AS1241 Fire Resistant Phosph
15、ate Ester Hydraulic Fluid for Aircraft AS1376 Alternate Dimensions, Center Body Section, Shape Fluid Fittings, Design Standard ARP4784 Definitions and Limits, Metal Material Defects and Surface and Edge Features, Fluid Couplings, Fittings and Hose Ends ARP5412 Aircraft Lightning Environment and Rela
16、ted Test Waveforms AS33514 Fitting End, Standard Dimensions for Flareless Tube Connection and Gasket Seal AS5863 Fitting End, 24 Cone, Flareless, Fluid Connection, Design Standard AS6115 Fitting Assembly, Straight, Male Flareless, Axially Swaged, Hydraulic, Up To 1500 psi AS6117 Fitting Assembly, Un
17、ion, Axially Swaged, Hydraulic, Up To 1500 psi AS6118 Fitting Assembly, Straight, Female Flareless, Axially Swaged, Hydraulic, Up To 1500 psi AS6119 Fitting Assembly, Elbow, 90, Axially Swaged, Hydraulic, Up To 1500 psi AS6120 Fitting Assembly, Elbow, 45, Axially Swaged, Hydraulic, Up To 1500 psi AS
18、6121 Fitting Assembly, Tee, Axially Swaged, Hydraulic, Up To 1500 psi AS6122 Fitting Assembly, Straight, Bulkhead, Flareless, Axially Swaged, Hydraulic, Up To 1500 psi AS6123 Fitting Assembly, Tee, Axially Swaged On The Run, Male Flareless On The Side, Hydraulic, Up To 1500 psi AS6124 Aluminum Axial
19、ly Swaged Fittings, Installation and Inspection Procedure AS6158 Fitting Assembly, Tee, Axially Swaged On The Run, Female Flareless On The Side, Hydraulic, Up To 1500 psi AS6159 Fitting Assembly, Tee, Axially Swaged To Female Flareless On The Run, Male Flareless On The Side, Hydraulic, Up To 1500 ps
20、i AS6445 Fitting Assembly, Tee, Axially Swaged On The Run, Bulkhead Flareless On The Side, Hydraulic, Up To 1500 psi AS6446 Fitting Assembly, Tee, Axially Swaged On The Run, Internal Port End On The Side, Hydraulic, Up To 1500 psi Copyright SAE International Provided by IHS under license with SAENot
21、 for ResaleNo reproduction or networking permitted without license from IHS-,-,-SAE AS6116 Page 3 of 39 AS6457 Fitting Assembly, Tee, Axially Swaged To Male Flareless On The Run, Male Flareless On The Side, Hydraulic, Up To 1500 psi AS6458 Fitting Assembly, Tee, Axially Swaged To Female Flareless On
22、 The Run, Female Flareless On The Side, Hydraulic, Up To 1500 psi AS6192 Fitting Assembly, Elbow, 90, Axially Swaged, Female Flareless, Hydraulic, Up To 1500 psi AS6193 Fitting Assembly, Elbow, 45, Axially Swaged, Female Flareless, Hydraulic, Up To 1500 psi AS6194 Fitting Assembly, Tee, Axially Swag
23、ed, Female Flareless On The Run, Axially Swaged On The Side, Hydraulic, Up To 1500 psi AS6195 Fitting Assembly, Tee, Male Flareless, Bulkhead Flareless On The Run, Axially Swaged On The Side, Hydraulic, Up To 1500 psi AS7003 NADCAP Program Requirements AS7112 National Aerospace and Defense Contracto
24、rs Accreditation Program (NADCAP) Requirements for Fluid System Components AS85449/2 Clamp Assembly, Saddle Type, Cushioned, Phosphate Ester Fluid ResistantAS85449/3 Clamp Assembly, Saddle Type, Cushioned, High TemperatureARP5416 Aircraft Lightning Test Methods ARP5412 Aircraft Lightning Environment
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- SAEAS61162011ALUMINUMFITTINGSAXIALLYSWAGEDTUBEWITHFLARELESSSEPARABLEFLUIDSYSTEMUPTO1500PSI10340KPAMAXIMUMSPECIFICATIONFOR

链接地址:http://www.mydoc123.com/p-1025086.html