SAE AS 6105-2011 FITTING TEE STANDARD AND REDUCER 37 PHERICAL FLARED《扩口球形37标准和异径管三通接头》.pdf

《SAE AS 6105-2011 FITTING TEE STANDARD AND REDUCER 37 PHERICAL FLARED《扩口球形37标准和异径管三通接头》.pdf》由会员分享，可在线阅读，更多相关《SAE AS 6105-2011 FITTING TEE STANDARD AND REDUCER 37 PHERICAL FLARED《扩口球形37标准和异径管三通接头》.pdf（5页珍藏版）》请在麦多课文档分享上搜索。

1、 SAE AS6105 ADOPTION NOTICE SAE AS6105, “Fitting, Tee, Standard And Reducer, 37 Spherical, Flared“, was adopted on 13 August 2014 for use by the Department of Defense (DoD). Proposed changes by DoD activities must be submitted to the DoD Adopting Activity: DLA Land and Maritime, ATTN: VAI, 3990 East

2、 Broad Street, Columbus, OH 43218-3990 or fluidflowdla.mil. Copies of these documents are available from SAE International, 400 Commonwealth Drive, Warrendale, PA 15096-0001, Tel: 877-606-7323 (inside USA and Canada) or 724-776-4970 (outside USA), www.sae.org. CONCLUDING MATERIAL Custodians: Prepari

3、ng activity: Army -AV DLA - CC Navy - AS Air Force - 99 (Project 4730-2014-066) DLA - CC NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above us

4、ing the ASSIST Online database at https:/assist.dla.mil. AMSC N/A FSC 4730 AEROSPACE STANDARD FITTING, TEE, STANDARD AND REDUCER, 37 SPHERICAL, FLARED AS6105Copyright 2011 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitte

5、d, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB

6、ADDRESS: http:/www.sae.org ISSUED 2011-08THIRD ANGLE PROJECTION CUSTODIAN: SAE G-3/G-3B FEDERAL SUPPLY CLASS 4730 AS6105SHEET 1 OF 4PROCUREMENT SPECIFICATION: /4/ AS6076SAE Technical Standards Board Rules provide that: “This report ispublishedby SAE toadvance thestate of technicalandengineering scie

7、nces. Theuse ofthis report is entirely voluntary, andits applicability and suitability forany particular use,including any patent infringement arising therefrom, isthe soleresponsibilityofthe user.”SAE reviews eachtechnicalreport at least every five years at which time itmay bereaffirmed, revised, o

8、rcancelled. SAE invites yourwrittencomments andsuggestions. SAE values your input. To provide feedbackon this Technical Report, please visit http:/www.sae.org/technical/standards/AS6105RATIONALE THIS SAE AEROSPACE STANDARD (AS) ESTABLISHES THE REQUIREMENTS FOR A TEE FITTING WITH 37 DEGREE SPHERICAL

9、FLARED TUBE. FIGURE 1 - TEE TABLE 1 DIMENSIONS AND WEIGHTS /11/ BASIC NO. AS6105/17/SIZE CODE V W LB/EAAPPROX. REF ALUMLB/EAAPPROX. REF CRESLB/EAAPPROX. REF TI02 .297- .314 .090 .0137 .0393 .0217 03 .360- .377 .100 .0200 .0575 .031704 .423- .440 .110 .0272 .0781 .0431 05 .485- .502 .120 .0355 .102 .

10、0562 06 .547- .565 .120 .0463 .133 .073408 .735- .753 .150 .0979 .281 .155 10 .860- .878 .170 .126 .362 .200 12 1.047-1.065 .185 .237 .681 .376 16 1.292-1.317 .205 .344 .987 .545 20 1.605-1.630 .240 .575 1.65 .911 24 1.855-1.880 .240 .788 2.26 1.25 32 2.542-2.572 .350 1.91 5.48 3.02 AEROSPACE STANDA

11、RD AS6105SHEET 2 OF 4FITTING, TEE, STANDARD AND REDUCER, 37 SPHERICAL, FLARED TABLE 2 LEG LENGTH A FORGING SIZE/10/TUBE SIZE OF PORT #1, #2, #3 02TUBE SIZE OF PORT #1, #2, #3 03TUBE SIZE OF PORT #1, #2, #3 04TUBE SIZE OF PORT #1, #2, #3 05TUBE SIZE OF PORT #1, #2, #3 06TUBE SIZE OF PORT #1, #2, #3 0

12、8TUBE SIZE OF PORT #1, #2, #3 10TUBE SIZE OF PORT #1, #2, #3 12TUBE SIZE OF PORT #1, #2, #3 16TUBE SIZE OF PORT #1, #2, #3 20TUBE SIZE OF PORT #1, #2, #3 24TUBE SIZE OF PORT #1, #2, #3 3202 .757 - - - - - - - - - - - 03 .789 .820 - - - - - - - - - - 04 .789 .811 .882 - - - - - - - - - 05 .843 .874 .

13、945 .945 - - - - - - - - 06 .946 .977 1.048 1.048 1.054 - - - - - - - 08 1.033 1.064 1.135 1.135 1.141 1.242 - - - - - - 10 1.135 1.166 1.237 1.237 1.243 1.344 1.445 - - - - - 12 1.232 1.263 1.334 1.334 1.340 1.441 1.542 1.648 - - - - 16 1.341 1.372 1.443 1.443 1.449 1.550 1.651 1.757 1.804 - - - 20

14、 1.544 1.575 1.646 1.646 1.652 1.753 1.854 1.960 2.007 2.054 - - 24 1.685 1.716 1.787 1.787 1.793 1.894 1.995 2.101 2.148 2.195 2.320 - 32 2.169 2.200 2.271 2.271 2.277 2.378 2.479 2.585 2.632 2.679 2.804 3.054 TABLE 3 TUBE SIZE AND CORRESPONDING THREAD PORT SIZE(NOMINAL TUBESIZE)T THREAD PER AS8879

15、 CLASS 3A 02 .125 .3125-24 UNJF 03 .188 .3750-24 UNJF04 .250 .4375-20 UNJF 05 .312 .5000-20 UNJF 06 .375 .5625-18 UNJF08 .500 .7500-16 UNJF 10 .625 .8750-14 UNJF 12 .750 1.0625-12 UNJ16 1.000 1.3125-12 UNJ 20 1.250 1.6250-12 UNJ 24 1.500 1.8750-12 UNJ32 2.000 2.5000-12 UNJ NOTES: NOTICE THIS DOCUMEN

16、T REFERENCES A PART WHICH CONTAINS CADMIUM AS A PLATING MATERIAL. CONSULT OFFICIALS IF YOU HAVE QUESTIONS CONCERNING CADMIUMS USE. /1/ MATERIAL: a. CODE LETTER F - TYPE 4140 ALLOY STEEL BAR PER AMS6349 OR AMS6382 OR TYPE 4130 ALLOY STEEL FORGING OR BAR PER AMS6370 OR AMS-S-6758 EXCEPT HEAT TREATMENT

17、 PER PROCUREMENT SPECIFICATION. b. CODE LETTER J - TYPE 304 CORROSION RESISTANT STEEL FORGING OR BAR PER AMS-QQ-S-763 OR AMS5639 EXCEPT HARDNESS PER PROCUREMENT SPECIFICATION. c. CODE LETTER K - TYPE 316 CORROSION RESISTANT STEEL FORGING OR BAR PER AMS-QQ-S-763 OR AMS5648 EXCEPT HARDNESS PER PROCURE

18、MENT SPECIFICATION. d. CODE LETTER R - TYPE 321 CORROSION RESISTANT STEEL FORGING OR BAR PER AMS-QQ-S-763 OR AMS5645 EXCEPT HARDNESS PER PROCUREMENT SPECIFICATION. AEROSPACE STANDARD AS6105SHEET 3 OF 4FITTING, TEE, STANDARD AND REDUCER, 37 SPHERICAL, FLARED e. CODE LETTER T - TYPE 6AL-4V TITANIUM AL

19、LOY FORGING OR BAR PER AMS4928. f. CODE LETTER W - TYPE 7075-T73 ALUMINUM ALLOY FORGING PER AMS4141 OR AMS-QQ-A-367; OR TYPE 7075-T73 ALUMINUM ALLOY BAR PER AMS-QQ-A-225/9; OR TYPE 7075-T7351 ALUMINUM ALLOY BAR PER AMS4124. 2. HEAT TREATMENT: a. MATERIAL CODE LETTER F - HARDNESS SHALL BE 92 HRB TO 4

20、0 HRC PER PROCUREMENT SPECIFICATION. b. OTHER MATERIAL CODE LETTERS NONE. 3. FINISH: a. MATERIAL CODE LETTER F - CADMIUM PLATE PER AMS-QQ-P-416, TYPE II, CLASS 2, DYE BLACK. b. MATERIAL CODE LETTER J, K, R PASSIVATE PER AMS2700, TYPE VI OR VII. c MATERIAL CODE LETTER T - FLUORIDE PHOSPHATE CONVERSIO

21、N COAT PER AMS2486 OR ANODIZE PER AMS2488, TYPE 2. d. MATERIAL CODE LETTER W: 1. ANODIZE PER AMS2472 OR MIL-A-8625, TYPE II, CLASS 2, DYE BROWN, DUPLEX SEAL PER PROCUREMENT SPECIFICATION. 2. W CODE PARTS TO BE COATED WITH HIGH PURITY ALUMINUM ONLY WILL HAVE THE FINISH CODE LETTER “V” AFTER THE SIZE

22、CODE IN THE PART NUMBER. HIGH PURITY ALUMINUM COAT PER PROCUREMENT SPECIFICATION. /4/ PROCUREMENT SPECIFICATION: AS6076 EXCEPT AS SPECIFIED ON THIS STANDARD. PRODUCT SUPPLIED TO THIS SPECIFICATION SHALL BE MANUFACTURED BY AN ACCREDITED MANUFACTURER LISTED IN THE NATIONAL AEROSPACE AND DEFENSE CONTRA

23、CTORS ACCREDITATION PROGRAM (NADCAP) QUALIFIED MANUFACTURER LIST (QML) FOR THIS PRODUCT TYPE. THE QML IS AVAILABLE AT ./5/ IDENTIFICATION AT LOCATION SHOWN: MARK PER AS478 CLASS C OR D, OR METHOD 7A3, 15A3, OR 15B. a. FOR SIZE 06 AND SMALLER: MANUFACTURERS NAME, CAGE CODE OR TRADEMARK, LETTER “AS” A

24、ND MATERIAL CODE LETTER. b. FOR SIZE 08 AND LARGER: MANUFACTURERS NAME, CAGE CODE OR TRADEMARK, BASIC PART NUMBER, AND MATERIAL CODE LETTER. 6. INTENDED USE: THIS PART IS DESIGNED FOR USE IN TUBING CONNECTION SYSTEMS WITH MAXIMUM OPERATING PRESSURES AS FOLLOWS: a. SIZES 02 THROUGH 16 IN LOW ALLOY ST

25、EEL, CORROSION RESISTANT STEEL AND TITANIUM ALLOY AT 3000 PSI. b. SIZES 02 THROUGH 12 IN ALUMINUM ALLOY AT 3000 PSI. c. SIZE 16 IN ALUMINUM ALLOY AND SIZE 20 THROUGH 32 IN ALL MATERIALS AT 1500 PSI. 7. FOR REDUCER CONFIGURATIONS, THE PRESSURE RATING IS DETERMINED BY THE LARGEST PORT. 8. THE NON-REDU

26、CER CONFIGURATION IS THE FUNCTIONAL EQUIVALENT OF AN824 AND MS24402 FOR THE CORRESPONDING FORGING SIZE AND IS INTENDED TO BE SUITABLE AS A REPLACEMENT STANDARD. 9. WHEN MACHINING FROM BAR STOCK OR OVERSIZED FORGING, THE CENTER BODY DIMENSIONS SHALL CONFORM TO AS1376, TABLE 1. /10/ THE DIMENSIONS IN

27、THE TABLE ARE FOR FINAL MACHINED PARTS. THE FORGING SIZE IS DETERMINED AS THE SIZE NECESSARY TO MAKE THE LARGEST FITTING END. /11/ WEIGHTS ARE FOR NON-REDUCERS ONLY. REDUCER FITTINGS WILL HAVE LOWER WEIGHTS. 12. INTERPRETATION OF DRAWING PER ARP4296. AEROSPACE STANDARD AS6105SHEET 4 OF 4FITTING, TEE

28、, STANDARD AND REDUCER, 37 SPHERICAL, FLARED 13. SURFACE TEXTURE: SYMBOLS PER ASME Y14.36M; REQUIREMENTS PER ASME B46.1. UNLESS OTHERWISE SPECIFIED, MACHINED SURFACES TO BE 125 IN RA. FORGED SURFACES MAY BE 250 IN RA. 14. BREAK ALL SHARP EDGES .003 TO .015 UNLESS OTHERWISE SPECIFIED. 15. DIMENSIONIN

29、G AND TOLERANCING: ASME Y14.5M-1994. 16. DIMENSIONS IN INCHES. UNLESS OTHERWISE SPECIFIED, TOLERANCES: LINEAR DIMENSIONS .016, ANGULAR DIMENSIONS 0 DEGREES 30. /17/ EXAMPLE OF PART NUMBER: NOTE: FOR THE SEQUENCE OF THE PORT NUMBERS IN THE PART NUMBER /17/, THE PORT #1 SHALL BE OF A LARGER SIZE OR OF

30、 THE SAME SIZE AS PORT #2. THE FINISH CODE LETTER “V” WILL BE PLACED HERE ONLY FOR MATERIAL CODE “W” PARTS THAT ARE TO BE COATED WITH HIGH PURITY ALUMINUMMATERIAL CODE LETTER /1/ SIZE CODE, TUBE SIZE OF PORT#2 IN .062 INCREMENTS AS6105 W 10 08 10 VBASIC PART NUMBER SIZE CODE, TUBE SIZE OF PORT #3 IN .062 INCREMENTS SIZE CODE FOR PORT #1 IN .062 INCREMENTS.