SAE AS 4577A-2001 Hose Assembly PTFE Para-Aramid Reinforced Standard Duty 3000 psi 275F Titanium Fittings Beam Seal 45 to 45《45对45角定向密封的钛配件、3000psi、275F标准型对位芳族增强聚四氟乙烯软管组件》.pdf

《SAE AS 4577A-2001 Hose Assembly PTFE Para-Aramid Reinforced Standard Duty 3000 psi 275F Titanium Fittings Beam Seal 45 to 45《45对45角定向密封的钛配件、3000psi、275F标准型对位芳族增强聚四氟乙烯软管组件》.pdf》由会员分享，可在线阅读，更多相关《SAE AS 4577A-2001 Hose Assembly PTFE Para-Aramid Reinforced Standard Duty 3000 psi 275F Titanium Fittings Beam Seal 45 to 45《45对45角定向密封的钛配件、3000psi、275F标准型对位芳族增强聚四氟乙烯软管组件》.pdf（5页珍藏版）》请在麦多课文档分享上搜索。

1、Copyright 2004 SAE InternationalAll rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, orotherwise, without the prior written permission of SAE.TO PLACE A DOCUMENT

2、ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: 724-776-4970 (outside USA)Fax: 724-776-0790 Email: custsvcsae.org SAE WEB ADDRESS: http:/www.sae.orgSAE Technical Standards Board Rules providethat: “This report is published by SAE to advancethe state oftechnical and engineering sciences.Theuse

3、ofthis reportisentirelyvoluntary, andits applicabilityand suitabilityfor any particularuse,including any patentinfringement arising therefrom,isthe sole responsibility of the user.”SAE reviews each technical reportatleastevery five years atwhich timeitmay bereaffirmed,revised, or cancelled.SAE invit

4、es yourwritten comments and suggestions.SHEET 1 OF 5AS4577REV.ATHIRD ANGLE PROJECTIONAEROSPACE STANDARDAS4577REV. AISSUED 1997-11 REVISED 2001-01 REAFFIRMED 2004-06(R) HOSE ASSEMBLY, PTFE, PARA-ARAMID REINFORCED,STANDARD DUTY, 3000 PSI, 275 F, TITANIUMFITTINGS, BEAM SEAL, 45 TO 45CUSTODIAN: SAE G-3/

5、G-3D PROCUREMENT SPECIFICATION: AS1975 /2/FEDERAL SUPPLY CLASS 4720FIGURE 1 - ENLARGED VIEW - 45 END FITTINGFIGURE 2 - ASSEMBLY ORIENTATIONCopyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-HOSE ASSEMBLY,

6、 PTFE, PARA-ARAMID REINFORCED,STANDARD DUTY, 3000 PSI, 275 F, TITANIUMFITTINGS, BEAM SEAL, 45 TO 45AEROSPACE STANDARDAS4577SHEET 2 OF 5AS4577REV.AREV. A(R)TABLE 1 - ASSEMBLY DIMENSIONSHOSEASSEMBLYNO. & SIZECODE /21/HOSESIZE(REF)THREAD TPER AS8879(REF)HOSEIDMINA1MAXCHEX(REF)D /8/DIA MAXWITHOUTSLEEVIN

7、GEMINEMAXSPHERICALBALL SIZEFORDETERMININGMINIMUMHOSEASSEMBLY ID /7/INAS4577E .250 .4375-20UNJS-3B .212 2.105 .56 .69 .310 .435 .115AS4577G .375 .5625-20UNJS-3B .298 2.380 .69 .80 .310 .435 .204AS4577H .500 .7188-20UNJS-3B .391 2.635 .88 .97 .314 .439 .289AS4577J .625 .8438-18UNJS-3B .485 3.500 1.00

8、1.15 .357 .482 .349AS4577K .750 1.000-16UNJ-3B .602 3.890 1.25 1.38 .385 .510 .434AS4577M 1.000 1.250-14UNJS-3B .852 4.405 1.50 1.66 .480 .605 .646TABLE 2 - HOSE OR SLEEVE OUTSIDE DIAMETERSLEEVECODE /22/ SLEEVE MATERIALTEMPLIMITF TOLERANCEHOSESIZE/10/.250HOSESIZE/10/.375HOSESIZE/10/.500HOSESIZE/10/.

9、625HOSESIZE/10/.750HOSESIZE/10/1.000- (-) INDICATES BRAIDED HOSEONLY PER AS1975275 MAXMIN.465.405.555.495.710.650.920.8501.075.9951.3651.285A FIRESLEEVE (AS1072 SIL - FG)(5 min) /11/ /12/275 MAXMIN.840.658.970.7881.150.9681.3801.1981.5901.3181.7501.568B FIRESLEEVE INTEGRALSILICONE (5 min) /13/275 MA

10、XMINC PROTECTIVE SLEEVESHRINK-ON (POLYOLEFINAS1073 CODE B)275 MAXMIN.520.450.620.550.795.7251.000.9201.1701.0601.4601.350TABLE 3 - ASSEMBLY LENGTH TOLERANCESHOSE ASSEMBLY LENGTH TOLERANCEUNDER 18 in .125 in18 TO 36 in EXCLUSIVE .250 in36 TO 50 in EXCLUSIVE .500 in50 in AND OVER 1%Copyright SAE Inter

11、national Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-HOSE ASSEMBLY, PTFE, PARA-ARAMID REINFORCED,STANDARD DUTY, 3000 PSI, 275 F, TITANIUMFITTINGS, BEAM SEAL, 45 TO 45AEROSPACE STANDARDAS4577SHEET 3 OF 5AS4577REV.AREV. A(R)NOT

12、ES:1. MATERIALS:a. HOSE AND FITTINGS - PER AS1975b. SLEEVES - SEE APPLICABLE STANDARDS, TABLE 2/2/ THIS PRODUCT SHALL BE QUALIFIED IN ACCORDANCE WITH PROCUREMENT SPECIFICATION AS1975 CLASS 3000. USERS OF THIS STANDARD SHALL PROCURE THIS PRODUCT FROM ACCREDITED MANUFACTURER(S), OR THEIR ACCREDITED DI

13、STRIBUTOR(S), AS LISTED IN THE PERFORMANCE REVIEW INSTITUTE (PRI) QUALIFIED PRODUCTS LIST PRI-QPL-AS1975 CLASS 3000 FOR THIS STANDARD. CHANGE-OVER FROM USER-QPL TO PRI-QPL SHALL BE IN ACCORDANCE WITH AS1975 REVISION C OR HIGHER AND BE COMPLETED WITHIN SIX MONTHS FROM THE DATE OF ISSUE OF THIS STANDA

14、RD.3. CONSTRUCTION AND PERFORMANCE PER AS1975 CLASS 3000. FITTINGS SHALL BE PERMANENTLY ATTACHED TO THE HOSE.4. OPERATING CHARACTERISTICS PER AS1975./5/ MARKING: MARKING SHALL BE PER AS1975 ON A STAINLESS STEEL BAND NOT OVER 1.0 in WIDE OR ON THE COLLAR. THE CHARACTERS SHALL BE A MINIMUM OF .06 in H

15、IGH. THE BAND SHALL BE SO DESIGNED AS TO REMAIN TIGHT ON THE HOSE TO PREVENT RELATIVE MOVEMENT AND RESULTANT CHAFING. IT SHALL BE OF SUFFICIENT STRENGTH TO PREVENT REMOVAL BY HAND. HOSE ASSEMBLY DATE AND “PT” SYMBOL SHALL BE PERMANENTLY MARKED ON THE BAND OR ON AN END FITTING OR A FIRESLEEVE CLAMP.

16、MARKING BAND SHALL BE COVERED WITH TRANSPARENT POLYOLEFIN SHRINK SLEEVE PER AS1073 CODE A./6/ LENGTH “L” IS A THREE DIGIT NUMBER OF WHICH THE FIRST TWO DIGITS DESCRIBE THE HOSE ASSEMBLY LENGTH IN WHOLE INCHES, AND THE THIRD DIGIT, THE FRACTION OF AN INCH IN EIGHTHS. LENGTH “L” IS MEASURED FROM THE O

17、UTER CORNER OF THE SEALING SURFACE TO OUTER CORNER OF SEALING SURFACE AS SHOWN IN FIGURE 1. FOR LENGTH TOLERANCES SEE TABLE 3./7/ A TRUE CIRCULAR CROSS SECTION IS NOT REQUIRED THROUGH THE FITTING ID. HOWEVER, THE APPLICABLE MINIMUM BALL DIAMETER LISTED IN TABLE 1 MUST BE CAPABLE OF PASSING THROUGH T

18、HE HOSE ASSEMBLY./8/ DISTANCE ACROSS CORNERS OF THE HEX MAY EXCEED THIS DIMENSION./9/ STANDARD COUPLING NUTS SHALL MATE WITH MIL-F-85421/1 OR AS4207 FITTING ENDS. NONSTANDARD COUPLING NUTS MAY BE USED PROVIDED THEY ARE FUNCTIONALLY EQUIVALENT AND PROVIDED THEY CANNOT BE REMOVED FROM THE FITTING. NUT

19、S SHALL MEET THE TORQUE TEST REQUIREMENTS PER AS1975.TABLE 4 - HOSE AND FITTING WEIGHTSHOSEOR SLEEVECODE /22/HOSE OR TYPESLEEVE UNITSHOSESIZE.250HOSESIZE.375HOSESIZE.500HOSESIZE.625HOSESIZE.750HOSESIZE1.000- BRAIDED HOSE ONLY PER AS1975 LB/IN (MAX) .006 .008 .012 .020 .025 .040A FIRESLEEVE AS1072 (5

20、 minPER AS1055) /15/LB/IN .012 .017 .018 .028 .030 .037B FIRESLEEVE INTEGRAL WITHHOSE (5 min PER AS1055) /15/LB/INC PROTECTIVE SLEEVE SHRINK-ON(POLYOLEFIN AS1073, CODE B)LB/IN .001 .001 .001 .002 .002 .003NONE FIRESLEEVE CLAMP LB/EA (REF) .020 .020 .021 .021 .025 .025NONE FITTING END (45) TITANIUM /

21、16/ LB/EA (REF) .060 .115 .188 .265 .470 .575Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-HOSE ASSEMBLY, PTFE, PARA-ARAMID REINFORCED,STANDARD DUTY, 3000 PSI, 275 F, TITANIUMFITTINGS, BEAM SEAL, 45

22、TO 45AEROSPACE STANDARDAS4577SHEET 4 OF 5AS4577REV.AREV. A(R)/10/ DIAMETERS ARE LISTED FOR CLAMP SELECTION. TUBULAR SLEEVES MAY NOT BE A PERFECT ROUND AND SHALL BE MEASURED WITH A DIAMETER TAPE RULE (OFTEN REFERRED TO AS A PI-TAPE)./11/ THE TABLE 2 SLEEVE DIAMETERS FOR AS1072 SLEEVES APPLY WHEN THE

23、SLEEVE IS COMPRESSED OR CLAMPED TO CONTACT THE HOSE. IN THIS CASE A WRINKLE MAY OCCUR OVER APPROXIMATELY 10% OF THE SLEEVE CIRCUMFERENCE./12/ THE CUT ENDS OF THE FIRESLEEVE SHALL BE COATED WITH RTV SILICONE RUBBER PRIOR TO INSTALLATION TO PREVENT WICKING OF FLUIDS. THE FIRESLEEVE ENDS SHALL BE SECUR

24、ED TO THE HOSE ASSEMBLY END FITTINGS WITH CORROSION RESISTANT STEEL BANDS. AFTER INSTALLATION, CRACKS OR VOIDS IN THE FIRESLEEVE WHICH EXPOSE THE FIBERGLASS SHALL BE COATED WITH RTV SILICONE RUBBER./13/ THE END OF THE INTEGRAL FIRESLEEVE SHALL BE COVERED WITH SILICONE EXTENDING OVER THE END FITTING

25、COLLAR.14. ADD “AS1055 TYPE IIb CLASS A-S/P” OR “AS150 TYPE XIII” TO IDENTIFICATION MARKING TO SHOW LEVEL OF COMPLIANCE, “FIRE RESISTANT” 275 F (5 min), WITH AS1055 OR AS150./15/ WHEN FIRESLEEVES ARE REQUIRED, WEIGHT LIMITS SHALL BE DEFINED BY THE PROCURING ACTIVITY./16/ TITANIUM PARTS MAY BE REPLAC

26、ED WITH STAINLESS STEEL IF MAXIMUM WEIGHT FOR FITTING IS NOT EXCEEDED AND THE STAINLESS STEEL COMPONENTS HAVE BEEN PREVIOUSLY QUALIFIED.17. DIMENSIONING AND TOLERANCING PER ASME Y14.5M-1994./18/ THE FITTING ORIENTATION DASH NUMBER IS A THREE DIGIT NUMBER DEFINING THE RELATIVE POSITION OF THE END FIT

27、TINGS IN 1 INCREMENTS (EXAMPLE 090 = 90). FITTING ORIENTATION SHALL BE MEASURED COUNTERCLOCKWISE FROM THE NEAREST END FITTING, WHICH SHALL BE IN THE RELATIVE 000 POSITION (SEE FIGURE 2). WHEN END FITTINGS ARE POINTED IN THE SAME DIRECTION, THIS DASH NUMBER SHALL BE 000./19/ SAFETY WIRE HOLES LOCATIO

28、N AND DIAMETER PER AS1043 CODED AS FOLLOWS:a. U = TWO HOLES 180 APARTb. W = THREE HOLES 120 APART20. THIS PART STANDARD TAKES PRECEDENCE IN CASES OF CONFLICT.21. THE SHRINK ON POLYOLEFIN SLEEVE SHALL COVER THE ENTIRE HOSE AND A MINIMUM OF 50% OF THE COLLARS ON BOTH ENDS OF THE ASSEMBLY./22/ EXAMPLE

29、OF PART NUMBER:Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-HOSE ASSEMBLY, PTFE, PARA-ARAMID REINFORCED,STANDARD DUTY, 3000 PSI, 275 F, TITANIUMFITTINGS, BEAM SEAL, 45 TO 45AEROSPACE STANDARDAS4577S

30、HEET 5 OF 5AS4577REV.AREV. A(R)23. ALL ASSEMBLIES PROCURED TO THIS STANDARD PRIOR TO REVISION A CAN BE UTILIZED FOR EITHER CLASS 3000 OR CLASS 4000 SYSTEM APPLICATIONS. ALL FUTURE PROCUREMENTS TO THIS STANDARD SHALL BE FOR CLASS 3000 ONLY. REFER TO AS4589 FOR PROCUREMENT OF CLASS 4000 HOSE ASSEMBLIE

31、S.24. THE CHANGE BAR ( l ) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT.Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-