SAE AS 3123A-2009 Plug Expansion - Aluminum 2024-T4 and 2024-T31 Short STD and 010 Oversize Diameters UNS A92024《膨胀插头 UNS A92024短型标准和 010特大直径2024-T4和2024-T31型铝》.pdf

《SAE AS 3123A-2009 Plug Expansion - Aluminum 2024-T4 and 2024-T31 Short STD and 010 Oversize Diameters UNS A92024《膨胀插头 UNS A92024短型标准和 010特大直径2024-T4和2024-T31型铝》.pdf》由会员分享，可在线阅读，更多相关《SAE AS 3123A-2009 Plug Expansion - Aluminum 2024-T4 and 2024-T31 Short STD and 010 Oversize Diameters UNS A92024《膨胀插头 UNS A92024短型标准和 010特大直径2024-T4和2024-T31型铝》.pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、AEROSPACE STANDARD (R) PLUG, EXPANSION - ALUMINUM, 2024-T4 AND 2024-T351, SHORT; STD AND .010 OVERSIZE DIAMETERS, UNS A92024 AS3123Copyright 2009 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any m

2、eans, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org IS

3、SUED 1981-02REAFFIRMED 2006-05 REVISED 2009-02THIRD ANGLE PROJECTION CUSTODIAN: E-25 REV.AFEDERAL SUPPLY CLASS 5315 AS3123SHEET 1 OF 3REV. APROCUREMENT SPECIFICATION: NONESAE TechnicalStandards Board Rules provide that: “This report is published by SAE toadvance thestate of technical andengineering

4、sciences. Theuse of thisreport is entirely voluntary, andits applicabilityandsuitability forany particularuse, including any patent infringement arising therefrom, is thesole responsibility oftheuser.”SAE reviews each technical report at least every five yearsat which time it may be reaffirmed, revi

5、sed, orcancelled. SAE invites yourwritten commentsandsuggestions. SAE values your input. To provide feedbackon this Technical Report, please visit http:/www.sae.org/technical/standards/AS3123ARATIONALE UPDATE SUPPLIER PART NUMBERS, CLARIFY PART MARKING, UPDATE MATERIAL USAGE AND GENERAL SAE UPDATING

6、 FOR OBSOLETE SPECIFICATIONS AND FORMATING REQUIREMENTS. FIGURE 1 TABLE 1A PART NUMBERS AND DIMENSIONSSTANDARD DIAMETER AEROSPACE STANDARD PART NUMBER /7/MANUFACTURERS PART NUMBER /7/A APPROX MASSLB/100 AS3123-01 PLGA0935010A .0928-.0937 .004 AS3123-02 PLGA1255010A .1241-.1250 .008 AS3123-03 PLGA156

7、5010A .1553-.1562 .014 AS3123-04 PLGA1875010A .1866-.1875 .020 AS3123-05 PLGA2185010A .2178-.2187 .031 AS3123-06 PLGA2505010A .2491-.2500 .047 AS3123-07 PLGA2815010A .2803-.2812 .064 AS3123-08 PLGA3435010A .3428-.3437 .121 AS3123-09 PLGA4065010A .4053-.4062 .177 AS3123-10 PLGA4685010A .4678-.4687 .2

8、22 AS3123-11 PLGA5315010A .5303-.5312 .387 AS3123-12 PLGA6565010A .6553-.6562 .611 Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AEROSPACE STANDARD AS3123SHEET 2 OF 3REV. APLUG, EXPANSION - ALUMINU

9、M, 2024-T4 AND 2024-T351, SHORT; STD AND .010 OVERSIZE DIAMETERS, UNS A92024 TABLE 1B PART NUMBERS AND DIMENSIONS .010 OVERSIZE DIAMETER AEROSPACE STANDARD PART NUMBER /7/MANUFACTURERS PART NUMBER /7/A APPROX MASSLB/100 AS3123-51 PLGA1035010A .1028-.1037 .006 AS3123-52 PLGA1355010A .1341-.1350 .010

10、AS3123-53 PLGA1665010A .1653-.1662 .017 AS3123-54 PLGA1975010A .1966-.1975 .025 AS3123-55 PLGA2285010A .2278-.2287 .038 AS3123-56 PLGA2605010A .2591-.2600 .056 AS3123-57 PLGA2915010A .2903-.2912 .074 AS3123-58 PLGA3535010A .3528-.3537 .140 AS3123-59 PLGA4165010A .4153-.4162 .202 AS3123-60 PLGA478501

11、0A .4778-.4787 .248 AS3123-61 PLGA5415010A .5403-.5412 .430 AS3123-62 PLGA6665010A .6653-.6662 .672 TABLE 1C PART NUMBERS AND DIMENSIONS AEROSPACE STANDARD PART NUMBER /7/B NOM CNOM DE NOM FGNOM HAS3123-01 SIZES 01 THRU 08 AND 51 THRU 58, AND AL ALLOY 2024-T351; SIZES 09 THRU 12 AND 59 THRU 62), OR

12、AMS-QQ-A-225/6 UNS A92024 (AL ALLOY 2024-T4; SIZES 01 THRU 08 AND 51 THRU 58, AND AL ALLOY 2024-T351; SIZES 09 THRU 12 AND 59 THRU 62). 2. FINISH: ANODIZE PER MIL-A-8625 TYPE IIB, CLASS 2. STANDARD PLUGS ARE DYED GREEN; .010 OVERSIZE PLUGS ARE DYED RED. 3. GROOVE BURRS PERMITTED ON OD OF PLUG TO .00

13、1 OVER MAX A. 4. SURFACE TEXTURE: SYMBOLS PER ASME Y14.36M, REQUIREMENTS PER ASME B46.1. UNLESS OTHERWISE SPECIFIED, SURFACES TO BE 250 MICROINCHES Ra. 5. BREAK EDGES .003 TO .015 UNLESS OTHERWISE SPECIFIED. Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduct

14、ion or networking permitted without license from IHS-,-,-AEROSPACE STANDARD AS3123SHEET 3 OF 3REV. APLUG, EXPANSION - ALUMINUM, 2024-T4 AND 2024-T351, SHORT; STD AND .010 OVERSIZE DIAMETERS, UNS A92024 6. DIMENSIONS IN INCHES. UNLESS OTHERWISE SPECIFIED, TOLERANCES: ANGULAR DIMENSIONS 2 DEGREES. DIM

15、ENSIONS APPLY AFTER FINISH. /7/ MARK AS3123-( ) PART NUMBER AND MANUFACTURERS PART NUMBER ON PACKAGE IN ACCORDANCE WITH AS478, METHOD 37. 8. USE WITH AS3124 PINS. SEE AIR3276 HOLE PREPARATION AND AIR3277 INSTALLATION PROCEDURES. 9. DIMENSIONING AND TOLERANCING: ASME Y14.5M-1994. 10. DO NOT USE UNASS

16、IGNED PART NUMBERS. 11. SEE AS3588 FOR PLUG AND PIN SET OF PARTS. 12. AS, AIR AND AMS ARE SAE INTERNATIONAL PUBLICATIONS. ASME IS AN AMERICAN SOCIETY OF MECHANICAL ENGINEERS PUBLICATION. MIL IS US GOVERNMENT PUBLICATION. 13. A CHANGE BAR ( l ) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE

17、 USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL

18、PUBLICATIONS, NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY. APPROVED SOURCE OF SUPPLY: THE LEE CO WESTBROOK, CT FEDERAL SUPPLY CODE FOR MANUFACTURERS NO 92555. ONLY THE ITEM DESCRIBED ON THIS DRAWING WHEN PROCURED FROM THE VENDOR LISTED HEREON IS APPROVED FOR USE IN THE APPLICATIONS SPECIFYI

19、NG THIS AEROSPACE STANDARD IDENTIFICATION NUMBER. A SUBSTITUTE ITEM SHALL NOT BE USED WITHOUT PRIOR TESTING AND APPROVAL BY THE DESIGN ACTIVITY RESPONSIBLE FOR THE APPLICATION. IDENTIFICATION OF THE APPROVED SOURCE HEREON IS NOT TO BE CONSTRUED AS A GUARANTEE OF PRESENT OR CONTINUED AVAILABILITY AS A SOURCE OF SUPPLY FOR THE ITEM DESCRIBED ON THE DRAWING. Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-