SAE AS 1339H-2017 Hose Assembly Polytetrafluoroethylene Metallic Reinforced 3000 psi 400 Lightweight Hydraulic and Pneumatic.pdf
《SAE AS 1339H-2017 Hose Assembly Polytetrafluoroethylene Metallic Reinforced 3000 psi 400 Lightweight Hydraulic and Pneumatic.pdf》由会员分享,可在线阅读,更多相关《SAE AS 1339H-2017 Hose Assembly Polytetrafluoroethylene Metallic Reinforced 3000 psi 400 Lightweight Hydraulic and Pneumatic.pdf(23页珍藏版)》请在麦多课文档分享上搜索。
1、_ SAE Technical Standards Board Rules provide that: “This report is published by SAE to advance the state of technical and engineering sciences. The use of this report is entirely voluntary, and its applicability and suitability for any particular use, including any patent infringement arising there
2、from, is the sole responsibility of the user.” SAE reviews each technical report at least every five years at which time it may be revised, reaffirmed, stabilized, or cancelled. SAE invites your written comments and suggestions. Copyright 2017 SAE International All rights reserved. No part of this p
3、ublication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-497
4、0 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org SAE values your input. To provide feedback on this Technical Report, please visit http:/standards.sae.org/AS1339H AEROSPACE STANDARD AS1339 REV. H Issued 1976-03 Reaffirmed 2007-07 Revised 2017-09 Supe
5、rseding AS1339G Hose Assembly, Polytetrafluoroethylene, Metallic Reinforced, 3000 psi, 400 F, Lightweight, Hydraulic and Pneumatic RATIONALE Add configuration for new integral abrasion sleeve and fluid barrier captured by the fitting. 1. SCOPE This Aerospace Standard (AS) defines the requirements fo
6、r a lightweight polytetrafluoroethylene (PTFE) lined, metallic reinforced, hose assembly suitable for use in high temperature, 400 F, high pressure, 3000 psi, aircraft hydraulic systems, also for use in pneumatic systems which allow some gaseous diffusion through the PTFE wall. 2. APPLICABLE DOCUMEN
7、TS The following publications form a part of this document to the extent specified herein. The latest issue of SAE publications shall apply. The applicable issue of other publications shall be the issue in effect on the date of the purchase order. In the event of conflict between the text of this do
8、cument and references cited herein, the text of this document takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 2.1 SAE Publications Available from SAE International, 400 Commonwealth Drive, Warrendale, PA 1
9、5096-0001, Tel: 877-606-7323 (inside USA and Canada) or +1 724-776-4970 (outside USA), www.sae.org. AMS2700 Passivation of Corrosion Resistant Steels AMS5557 Steel, Corrosion and Heat-Resistant, Seamless or Welded Hydraulic Tubing 18.5Cr - 10.5Ni - 0.40Ti (SAE 30321) Solution Heat Treated AMS5561 St
10、eel, Corrosion and Heat-Resistant, Welded and Drawn or Seamless and Drawn Tubing 9.0Mn - 20Cr - 6.5Ni - 0.28N High-Pressure Hydraulic AMS5565 Steel, Corrosion Resistant, Welded Tubing 19Cr - 9.5Ni (304) Solution Heat Treated AMS5566 Steel, Corrosion Resistant, Seamless or Welded Hydraulic Tubing 19C
11、r - 10Ni (304) High Pressure, Cold Drawn SAE INTERNATIONAL AS1339H Page 2 of 23 AMS5567 Steel, Corrosion Resistant, Seamless or Welded Hydraulic Tubing 19Cr - 10Ni (304) Solution Heat Treated AMS5570 Steel, Corrosion and Heat-Resistant, Seamless Tubing 18Cr - 11Ni - 0.40Ti (321) Solution Heat Treate
12、d AMS5573 Steel, Corrosion and Heat-Resistant, Seamless Tubing 17Cr - 12Ni - 2.5Mo (SAE 30316) Solution Heat Treated AMS5575 Steel, Corrosion and Heat-Resistant, Welded Tubing 18Cr - 10.5Ni - 0.70Cb (Nb) (347) Solution Heat Treated AMS5581 Nickel Alloy, Corrosion and Heat-Resistant, Seamless or Weld
13、ed Tubing 62Ni - 21.5Cr - 9.0Mo - 3.7Cb (Nb) Annealed AMS5639 Steel, Corrosion-Resistant, Bars, Wire, Forgings, Mechanical Tubing, and Rings 19Cr - 10Ni Solution Heat Treated AMS5643 Steel, Corrosion Resistant, Bars, Wire, Forgings, Tubing, and Rings 16Cr - 4.0Ni - 0.30(Cb+Ta) - 4.0Cu Solution Heat
14、Treated, Precipitation Hardenable AMS5644 Steel Bars and Forgings, Corrosion Heat Resistant, 17Cr - 7Ni - 1Al AMS5645 Steel, Corrosion and Heat Resistant, Bars, Wire, Forgings, Tubing, and Rings 18Cr - 10Ni - 0.40Ti (321) Solution Heat Treated AMS5646 Steel, Corrosion and Heat-Resistant, Bars, Wire,
15、 Forgings, Tubing, and Rings 18Cr - 11Ni - 0.60Cb(Nb) (347) Solution Heat Treated AMS5647 Steel, Corrosion-Resistant, Bars, Wire, Forgings, Mechanical Tubing, and Rings 19Cr - 9.5Ni Solution Heat Treated AMS5648 Steel, Corrosion and Heat-Resistant, Bars, Wire, Forgings, Tubing, and Rings, 17Cr - 12N
16、i - 2.5Mo (316) Solution Heat Treated AMS5653 Steel, Corrosion and Heat-Resistant, Bars, Wire, Forgings, Tubing, and Rings 17Cr - 12Ni - 2.5Mo (0.030 Max C) (316L) Solution Heat Treated AMS5659 Steel, Corrosion-Resistant, Bars, Wire, Forgings, Rings, and Extrusions 15Cr - 4.5Ni - 0.30Cb (Nb) - 3.5Cu
17、 AMS5666 Nickel Alloy, Corrosion and Heat-Resistant, Bars, Forgings, Extrusions, and Rings 62Ni - 21.5Cr - 9.0Mo - 3.65Cb (Nb) Annealed AMS5688 Steel, Corrosion-Resistant, Wire 18Cr - 9.0Ni (SAE 30302) Spring Temper AMS5689 Steel, Corrosion and Heat Resistant, Wire 18Cr - 10.5Ni - 0.40Ti (SAE 30321)
18、 Solution Heat Treated AMS5690 Steel, Corrosion and Heat Resistant, Wire 17Cr - 12Ni - 2.5Mo (316) Solution Heat Treated AMS5697 Steel, Corrosion-Resistant, Wire 19Cr - 9.5Ni (SAE 30304) Solution Heat Treated AMS5743 Steel, Corrosion and Heat-Resistant, Bars and Forgings 15.5Cr - 4.5Ni - 2.9Mo - 0.1
19、0N Solution Heat Treated, Sub-Zero Cooled, Equalized, and Over-Tempered AMS-QQ-S-763 Steel, Corrosion Resistant, Bars, Wire, Shapes, and Forgings AIR4092 Investigation of PTFE “Melt“ Phenomenon for High Pressure Hoses SAE INTERNATIONAL AS1339H Page 3 of 23 ARP908 Torque Requirements, Installation an
20、d Qualification Test, Hose and Tube Fitting ARP1835 Preparation for Delivery, General Requirements for Hose Assemblies AS150 Hose Assembly, Type Classifications of, Basic Performance and Fire Resistance AS611 Hose Assembly and Tubing, Polytetrafluoroethylene, Cleaning Methods for AS1055 Fire Testing
21、 of Flexible Hose, Tube Assemblies, Coils, Fittings, and Similar System Components AS1072 Sleeve, Hose Assembly, Fire Protection AS2078 Test Methods, Hose Assemblies, Polytetrafluoroethylene (PTFE) AS4375 Fitting End, Flareless, Design Standard AS4395 Fitting End, Flared, Tube Connection, Design Sta
22、ndard AS7003 Nadcap Program Requirements AS7112 National Aerospace and Defense Contractors Accreditation Program Requirements for Fluid System Components AS8879 Screw Threads - UNJ Profile, Inch Controlled Radius Root with Increased Minor Diameter AS33514 Fitting End, Standard Dimensions for Flarele
23、ss Tube Connection and Gasket Seal AS85421 Fittings, Tube, Fluid Systems, Separable, Beam Seal, 3000/4000 psi, General Specification For AS85421/1 Fitting End, Standard Dimensions for Dynamic Beam Seal, Male 2.2 ASME Publications Available from ASME, P.O. Box 2900, 22 Law Drive, Fairfield, NJ 07007-
24、2900, Tel: 800-843-2763 (U.S./Canada), 001-800-843-2763 (Mexico), 973-882-1170 (outside North America), www.asme.org. ASME B46.1 Surface Texture ASME Y14.100M Engineering Drawing Practices 2.3 ASTM Publications Available from ASTM International, 100 Barr Harbor Drive, P.O. Box C700, West Conshohocke
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- SAEAS1339H2017HOSEASSEMBLYPOLYTETRAFLUOROETHYLENEMETALLICREINFORCED3000PSI400LIGHTWEIGHTHYDRAULICANDPNEUMATICPDF

链接地址:http://www.mydoc123.com/p-1023471.html