SAE AMS 3329B-2010 Fluorosilicone (FVMQ) Rubber Fuel and Oil Resistant High Strength 45 - 55《高强度耐燃料和汽油的氟硅橡胶(FVMQ) 45-55》.pdf

《SAE AMS 3329B-2010 Fluorosilicone (FVMQ) Rubber Fuel and Oil Resistant High Strength 45 - 55《高强度耐燃料和汽油的氟硅橡胶(FVMQ) 45-55》.pdf》由会员分享，可在线阅读，更多相关《SAE AMS 3329B-2010 Fluorosilicone (FVMQ) Rubber Fuel and Oil Resistant High Strength 45 - 55《高强度耐燃料和汽油的氟硅橡胶(FVMQ) 45-55》.pdf（7页珍藏版）》请在麦多课文档分享上搜索。

1、_SAE Technical Standards Board Rules provide that: “This report is published by SAE to advance the state of technical and engineering sciences. The use of this report is entirely voluntary, and its applicability and suitability for any particular use, including any patent infringement arising theref

2、rom, is the sole responsibility of the user.” SAE reviews each technical report at least every five years at which time it may be reaffirmed, revised, or cancelled. SAE invites your written comments and suggestions. Copyright 2010 SAE International All rights reserved. No part of this publication ma

3、y be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside US

4、A) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.orgSAE values your input. To provide feedback on this Technical Report, please visit http:/www.sae.org/technical/standards/AMS3329BAEROSPACEMATERIALSPECIFICATIONAMS3329 REV. B Issued 1984-07 Reaffirmed 2001-04 Revised

5、2010-05 Superseding AMS3329A Fluorosilicone (FVMQ) Rubber Fuel and Oil Resistant, High Strength 45 - 55 RATIONALEAMS3329B is a Five Year Review and update of this specification. 1. SCOPE 1.1 Form This specification covers a fluorosilicone (FVMQ) rubber in the form of sheet, strip, tubing, extrusions

6、, and molded shapes.1.2 Application These products have been used typically for parts requiring resistance to jet fuel and lubricating oils, but usage is not limited to such applications. Generally, products are usable over a temperature range of -76 to +302 F (-60 to +150 C). Each application, howe

7、ver, has to be considered individually. 1.3 Safety-Hazardous Materials While the materials, methods, applications, and processes described or referenced in this specification may involve the use of hazardous materials, this specification does not address the hazards which may be involved in such use

8、. It is the sole responsibility of the user to ensure familiarity with the safe and proper use of any hazardous materials and to take necessary precautionary measures to ensure the health and safety of all personnel involved. 2. APPLICABLE DOCUMENTS The issue of the following documents in effect on

9、the date of the purchase order forms a part of this specification to the extent specified herein. The supplier may work to a subsequent revision of a document unless a specific document issue is specified. When the referenced document has been cancelled and no superseding document has been specified

10、, the last published issue of that document shall apply. 2.1 SAE Publications Available from SAE International, 400 Commonwealth Drive, Warrendale, PA 15096-0001, Tel: 877-606-7323 (inside USA and Canada) or 724-776-4970 (outside USA), www.sae.org.AMS2279 Tolerances, Rubber Products AMS2810 Identifi

11、cation and Packaging, Elastomeric Products AMS3021 Fluid, Reference, for Testing Di-Ester (Polyol) Resistant Material Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SAE AMS3329B Page 2 of 72.2 ASTM

12、Publications Available from ASTM International, 100 Barr Harbor Drive, P.O. Box C700, West Conshohocken, PA 19428-2959, Tel: 610-832-9585, www.astm.org.ASTM D 297 Standard Test Methods for Rubber Products Chemical Analysis ASTM D 395 Standard Test Methods for Rubber Property Compression Set ASTM D 4

13、12 Standard Test Methods for Vulcanized Rubber and Thermoplastic Elastomers - Tension ASTM D 471 Standard Test Methods for Rubber Property - Effect of Liquids ASTM D 573 Standard Test Methods for Rubber Deterioration - in an Air Oven ASTM D 624 Standard Test Methods for Tear Strength of Conventional

14、 Vulcanized Rubber and Thermoplastic Elastomers ASTM D 1329 Standard Test Methods for Evaluating Rubber Property Retraction at Low Temperatures (TR Test)ASTM D 1415 Standard Test Methods for Rubber Property - International Hardness ASTM D 2240 Standard Test Methods for Rubber Property - Durometer Ha

15、rdness 3. TECHNICAL REQUIREMENTS 3.1 Material Shall be a compound, based on a fluorosilicone (FVMQ) elastomer, suitably cured to produce a product meeting the requirements of 3.2. 3.1.1 Color Shall be blue. 3.2 Properties The product shall conform to requirements shown in Table 1. Tests shall be per

16、formed on the product supplied and in accordance with specified ASTM methods, insofar as practicable. Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SAE AMS3329B Page 3 of 7TABLE 1 - PROPERTIES Para

17、graph Property Requirement Test Method 3.2.1 Hardness, Durometer “A” or equivalent 50 5 ASTM D 2240 or ASTM D 1415 3.2.2 Tensile Strength, minimum 1150 psi (7.93 MPa) ASTM D 412, Die B or C 3.2.3 Elongation, minimum 350% ASTM D 412, Die B or C 3.2.4 Tear Resistance, minimum 150 pounds force per inch

18、 (26.3 kN/m) ASTM D 624, Die C 3.2.5 Specific Gravity Preproduction Value 0.03 ASTM D 297 3.2.6 Di-Ester Oil Resistance (Immediate Deteriorated Properties)ASTM D 471 AMS3021Temperature: 302 F 5 (150 C 3) Time: 70 hours 0.53.2.6.1 Hardness Change, Durometer “A” or equivalent -15 to +15 3.2.6.2 Tensil

19、e Strength Change, maximum -40%3.2.6.3 Elongation Change, maximum -30% 3.2.6.4 Volume Change +1 to +15% 3.2.7 Aromatic Fuel Resistance (Immediate Deteriorated Properties)ASTM D 471 ASTM Ref. Fuel B Temperature: 68 to 86 F (20 to 30 C)Time: 22 hours 0.53.2.7.1 Hardness Change, Durometer “A” or equiva

20、lent -253.2.7.2 Tensile Strength Change, maximum -40%3.2.7.3 Elongation Change, maximum -30% 3.2.7.4 Volume Change, maximum +1 to 25% 3.2.8 Dry Heat Resistance ASTM D 573 Temperature: 392 F 5 (200 C 3) Time: 70 hours 0.53.2.8.1 Hardness Change, Durometer “A” or equivalent -5 to +10 3.2.8.2 Tensile S

21、trength Change, maximum -30%3.2.8.3 Elongation Change, maximum -30% 3.2.9 Compression Set ASTM D 395, Method B Temperature: 347 F 5 (175 C 3) Time: 22 hours 0.53.2.9.1 Percent of Original Deflection, maximum 403.2.10 Low-Temperature Resistance ASTM D 1329, Method A 3.2.10.1 Temperature Retraction, T

22、R10point, maximum Temperature: -71 F (-57 C) Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SAE AMS3329B Page 4 of 73.2.11 Corrosion The product shall not have a corrosive effect on other materials

23、when exposed to conditions normally encountered in service, determined by a procedure agreed upon by purchaser and supplier. Discoloration of metal shall not be considered objectionable. 3.3 Quality The product, as received by purchaser, shall be uniform in quality and condition, smooth, as free fro

24、m foreign material as commercially practicable, and free from imperfections detrimental to usage of the product. 3.4 Tolerances Shall conform to all applicable requirements of AMS2279. 4. QUALITY ASSURANCE PROVISIONS 4.1 Responsibility for Inspection The manufacturer of the product shall supply all

25、samples for required tests and shall be responsible for the performance of all required tests. Purchaser reserves the right to sample and to perform any confirmatory testing deemed necessary to ensure that the product conforms to specified requirements. 4.2 Classification of Tests 4.2.1 Acceptance T

26、ests Tests for requirements shown in Table 2 are acceptance tests and shall be performed on each lot. TABLE 2 - ACCEPTANCE TESTS Requirement Paragraph HardnessTensile Strength ElongationVolume Change in Fuel Compression Set Quality3.2.13.2.23.2.33.2.7.43.2.93.34.2.2 Preproduction Tests All technical

27、 requirements are preproduction tests and shall be performed prior to or on the initial shipment of a product by the manufacturer, when a change in ingredients and/or processing requires reapproval as in 4.4.1 and when purchaser deems confirmatory testing to be required. Copyright SAE International

28、Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SAE AMS3329B Page 5 of 74.3 Sampling and Testing Shall be as follows: 4.3.1 For Acceptance Tests Sufficient product shall be taken at random from each lot to perform all required

29、tests. The number of determinations for each requirement shall be as specified in the applicable test procedure or, if not specified therein, not less than three. 4.3.1.1 If specimens cannot be prepared from the product, ASTM test specimens, prepared from the same batch and state of cure, shall be u

30、sed for required tests. When the product supplied is an extrusion of such shape that suitable test specimens cannot be cut from the product, a separate flat strip test sample, from the same production lot, shall be supplied upon request. This strip shall be prepared from tubing 1.000 inch 0.063 (25.

31、40 mm 1.60) in OD by 0.075 inch 0.008 (1.90 mm 0.20) in wall thickness, mechanically slit and flattened into a strip while being extruded, and cured in the same manner as production product. When the product is a molded shape from which test specimens cannot be cut, a slab 6 inches (152 mm) square b

32、y 0.075 inch 0.008 (1.90 mm 0.20) thick, molded from the same batch of compound, shall be supplied upon request.4.3.1.2 A lot shall be all product from the same batch of compound processed in one continuous run and presented for manufacturers inspection at one time. 4.3.1.3 A batch shall be the quan

33、tity of compound run through a mill or mixer at one time. 4.3.1.4 Final inspection Sampling Plan A statistical sampling plan acceptable to the purchaser may be used in lieu of sampling as in 4.3.1. Sample size for visual and dimensional requirements shall be as shown in Table 3; sample unit shall be

34、 one molded part and acceptance based on zero defects. TABLE 3 - VISUAL AND DIMENSIONAL INSPECTION Lot Size Sample Size 2 to 8 Entire Lot 9 to 90 8 91 to 150 12 151 to 280 19 281 to 500 21 501 to 1200 27 1201 to 3200 35 3201 to 10 000 38 10 001 to 35 000 46 35 001 to 150 000 56 150 001 and Over 65 C

35、opyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SAE AMS3329B Page 6 of 74.3.2 For Preproduction Tests As agreed upon by purchaser and manufacturer. 4.4 Approval 4.4.1 Manufacturer shall establish for

36、each size of part, parameters for the process control factors which will produce parts meeting the technical requirements of this specification. These shall constitute the approved procedures and shall be used for manufacturing production of parts. If necessary to make any changes in the parameters

37、for process control factors, manufacturer shall submit for re-approval a statement of the proposed changes in ingredients, and/or processing. Products manufactured using a revised procedure shall not be shipped prior to reapproval in writing. Manufacturer shall use ingredients, manufacturing procedu

38、res, processes, and methods of inspection, which are essentially the same as those used on the approved sample. 4.4.1.1 Control factors for producing products include but are not limited to, the following: Compound ingredients and proportions thereof within established limits Sequence of mixing comp

39、ound ingredients Type of mixing equipment Method and equipment for preparing preforms Basic molding procedure (compression, transfer, injection) Curing time and pressure; variations of 10% are permissible Finishing methods Methods of inspection 4.4.1.2 Any of the above process control factors for wh

40、ich parameters are considered proprietary by the manufacturer may be assigned a code designation. Each variation in such parameters shall be assigned a modified code designation.4.5 Reports The supplier of the product shall furnish with each shipment a report showing the results of tests to determin

41、e conformance to the acceptance test requirements and stating that the product conforms to the other technical requirements. This report shall include the purchase order number, lot number, AMS3329B, manufacturers compound number, form and size or part number, and quantity. 4.6 Resampling and Retest

42、ing If any specimen used in the above tests fails to meet the specified requirements, disposition of the product may be based on the results of testing three additional specimens for each original nonconforming specimen. Failure of any retest specimen to meet the specified requirements shall be caus

43、e for rejection of the product represented. Results of all tests shall be reported. 5. PREPARATION FOR DELIVERY 5.1 Identification and Packaging Shall be as stated on the purchase order or contract requirement, when no requirements are stipulated, packaging shall be in accordance with AMS2810. 5.1.1

44、 A lot of product may be packaged in small quantities and delivered under the basic lot approval provided lot identification is maintained. Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SAE AMS3329

45、B Page 7 of 76. ACKNOWLEDGMENT Supplier shall mention this specification number and its revision letter in all quotations and when acknowledging purchase orders.7. REJECTIONS Product not conforming to this specification, or to modifications authorized by purchaser, will be subject to rejection. 8. N

46、OTES 8.1 A change bar (l) located in the left margin is for the convenience of the user in locating areas where technical revisions, not editorial changes, have been made to the previous issue of this document. An (R) symbol to the left of the document title indicates a complete revision of the docu

47、ment, including technical revisions. Change bars and (R) are not used in original publications, nor in documents that contain editorial changes only. 8.2 Dimensions and properties in inch/pound units and the Fahrenheit temperatures are primary; dimensions and properties in SI units and the Celsius t

48、emperatures are shown as the approximate equivalents of the primary units and are presented only for information. 8.3 Purchase documents should specify not less than the following: AMS3329BForm and size or part number of product desired Quantity of product desired Special packaging if required 8.4 Similar Specifications MIL-DTL-25988, Type II, Class 2, Grade 50, is listed for information only and shall not be construed as an acceptable alternate unless all requirements of this AMS are met. PRE