REG NASA-LLIS-1037-2001 Lessons Learned Machining of thermoplastic polymers.pdf

《REG NASA-LLIS-1037-2001 Lessons Learned Machining of thermoplastic polymers.pdf》由会员分享，可在线阅读，更多相关《REG NASA-LLIS-1037-2001 Lessons Learned Machining of thermoplastic polymers.pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、Lessons Learned Entry: 1037Lesson Info:a71 Lesson Number: 1037a71 Lesson Date: 2001-08-22a71 Submitting Organization: WSTFa71 Submitted by: Jess WallerSubject: Machining of thermoplastic polymers Description of Driving Event: The Primary Reaction Control System (PRCS) pilot-operated valve (POV) cont

2、rols the flow of hypergolic liquid propellants nitrogen tetroxide (oxidizer) and monomethylhydrazine (fuel) to the Space Shuttle Orbiter attitude control thrusters. The POV has experienced numerous in-flight and ground turnaround failures, including leakage and failure to open upon command. Corrosio

3、n in the oxidizer valves and seal extrusion in the fuel valves have been implicated in most failures. The desire to mitigate corrosion and seal extrusion led to an effort to develop a redesigned POV (RPOV) pilot seat assembly.Machining of polytetrafluoroethylene (PTFE) pre-forms for the RPOV pilot s

4、eals was found to be a demanding art requiring special tooling, support equipment, and practice. For example, the need to machine PTFE to close tolerances can be thwarted by slight temperature changes. Given the small size of the machined parts (Figure 1) and the close tolerances required (Figure 2)

5、, it was essential to see and accurately measure the article being machined.refer to D descriptionDProvided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Figure 1. RPOV seat assembly piece-parts (Left: MP35N seat, Middle: PTFE preform, Right: MP35N retainer

6、)refer to D descriptionDFigure 2. Final RPOV seat assembly design configurationAlso, proper cutting tool size, shape, material, cutting angle, nose radius, sharpening technique, cutting speed, and coolant were important considerations in obtaining desired tolerances and surface finish.Lesson(s) Lear

7、ned: Machining of polymers such as polytetrafluoroethylene (PTFE) used in the fabrication of small piece-parts made to close tolerances presents special challenges.Recommendation(s): Appropriate experience and tooling must be sought, and ample time allocated for practice before viable seal preforms

8、can be machined. For example, machining of PTFE to close tolerances using a conventional lathe required spraying isopropyl alcohol (IPA) directly on the PTFE during preform fabrication and final trimming to create the final seal profile. Implementation of established machining guidelines for PFTE wa

9、s also found to be essential 1. Accurate machining of small RPOV piece-parts was further assisted by the use of a video microscope and monitor system with “in-process“ measurement and inspection capability.Reference:1. Product Literature. Teflon PTFE Properties Handbook, DuPont and Nemours and Compa

10、ny, Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Specialty Polymers, Wilmington, DE, November 1992.Evidence of Recurrence Control Effectiveness: N/ADocuments Related to Lesson: N/AMission Directorate(s): a71 Exploration Systemsa71 Aeronautics Rese

11、archAdditional Key Phrase(s): a71 Hardwarea71 Industrial Operationsa71 Parts Materials & Processesa71 Test & VerificationAdditional Info: Approval Info: a71 Approval Date: 2001-12-11a71 Approval Name: Jan Jungewaeltera71 Approval Organization: WSTFa71 Approval Phone Number: 505-524-5161Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-