NEMA C12 20-2010 Electricity Meters 0 2 and 0 5 Accuracy Classes《精确度为0 2和0 5的电量计》.pdf

《NEMA C12 20-2010 Electricity Meters 0 2 and 0 5 Accuracy Classes《精确度为0 2和0 5的电量计》.pdf》由会员分享，可在线阅读，更多相关《NEMA C12 20-2010 Electricity Meters 0 2 and 0 5 Accuracy Classes《精确度为0 2和0 5的电量计》.pdf（33页珍藏版）》请在麦多课文档分享上搜索。

1、 ANSI C12.20-2010 American National Standard for Electricity Meters 0.2 and 0.5 Accuracy Classes ANSI C12.20-2010 Revision of ANSI C12.20-2002 American National Standard for Electricity Meters 0.2 and 0.5 Accuracy Classes NOTICE OF ADOPTION ANSI C12.20 was adopted and is approved for use by the Depa

2、rtment of Defense (DoD). The National Electrical Manufacturers Association has furnished the clearance required by existing regulations. Copies of the document are stocked at the Standardization Documents Order Desk, Building 4D, 700 Robbins Avenue, Philadelphia, PA 19111-5094, for issue to DoD acti

3、vities only. All other requestors must obtain copies from NEMA. Secretariat: National Electrical Manufacturers Association Approved August 31, 2010 American National Standards Institute, Inc. ANSI C12.20-2010 NOTICE AND DISCLAIMER The information in this publication was considered technically sound

4、by the consensus of persons engaged in the development and approval of the document at the time it was developed. Consensus does not necessarily mean that there is unanimous agreement among every person participating in the development of this document. NEMA standards and guideline publications, of

5、which the document contained herein is one, are developed through a voluntary consensus standards development process. This process brings together volunteers and/or seeks out the views of persons who have an interest in the topic covered by this publication. While NEMA administers the process and e

6、stablishes rules to promote fairness in the development of consensus, it does not write the document and it does not independently test, evaluate, or verify the accuracy or completeness of any information or the soundness of any judgments contained in its standards and guideline publications. NEMA d

7、isclaims liability for any personal injury, property, or other damages of any nature whatsoever, whether special, indirect, consequential, or compensatory, directly or indirectly resulting from the publication, use of, application, or reliance on this document. NEMA disclaims and makes no guaranty o

8、r warranty, express or implied, as to the accuracy or completeness of any information published herein, and disclaims and makes no warranty that the information in this document will fulfill any of your particular purposes or needs. NEMA does not undertake to guarantee the performance of any individ

9、ual manufacturer or sellers products or services by virtue of this standard or guide. In publishing and making this document available, NEMA is not undertaking to render professional or other services for or on behalf of any person or entity, nor is NEMA undertaking to perform any duty owed by any p

10、erson or entity to someone else. Anyone using this document should rely on his or her own independent judgment or, as appropriate, seek the advice of a competent professional in determining the exercise of reasonable care in any given circumstances. Information and other standards on the topic cover

11、ed by this publication may be available from other sources, which the user may wish to consult for additional views or information not covered by this publication. NEMA has no power, nor does it undertake to police or enforce compliance with the contents of this document. NEMA does not certify, test

12、, or inspect products, designs, or installations for safety or health purposes. Any certification or other statement of compliance with any health or safetyrelated information in this document shall not be attributable to NEMA and is solely the responsibility of the certifier or maker of the stateme

13、nt. ANSI C12.20-2010 AMERICAN NATIONAL STANDARD Approval of an American National Standard requires verification by ANSI that the requirements for due process, consensus, and other criteria for approval have been met by the standards developer. Consensus is established when, in the judgment of the AN

14、SI Board of Standards Review, substantial agreement has been reached by directly and materially affected interests. Substantial agreement means much more than a simple majority, but not necessarily unanimity. Consensus requires that all views and objections be considered, and that a concerted effort

15、 be made toward their resolution. The use of American National Standards is completely voluntary; their existence does not in any respect preclude anyone, whether he has approved the standards or not, from manufacturing, marketing, purchasing, or using products, processes, or procedures not conformi

16、ng to the standards. The American National Standards Institute does not develop standards and will in no circumstances give an interpretation of any American National Standard. Moreover, no person shall have the right or authority to issue an interpretation of an American National Standard in the na

17、me of the American National Standards Institute. Requests for interpretations should be addressed to the secretariat or sponsor whose name appears on the title page of this standard. Caution Notice: This American National Standard may be revised or withdrawn at any time. The procedures of the Americ

18、an National Standards Institute require that action be taken periodically to reaffirm, revise, or withdraw this standard. Purchasers of American National Standards may receive current information on all standards by calling or writing the American National Standards Institute. Published by National

19、Electrical Manufacturers Association 1300 North 17th Street, Rosslyn, VA 22209 Copyright 2010 by National Electrical Manufacturers Association. All rights reserved including translation into other languages, reserved under the Universal Copyright Convention, the Berne Convention for the Protection o

20、f Literary and Artistic Works, and the International and Pan American Copyright Conventions. No part of this publication may be reproduced in any form, in an electronic retrieval system or otherwise, without the prior written permission of the publisher. Printed in the United States of America i ANS

21、I C12.20-2010 This page intentionally left blank.ii ANSI C12.20-2010 Contents 1 SCOPE 1 2 DEFINITIONS 1 3 REFERENCES 1 4 REQUIREMENTS1 4.1 Mounting.1 4.2 Voltage and frequency1 4.3 Current classes and test amperes1 4.4 Form designations 2 4.5 Displays 2 4.5.1 Viewing requirements2 4.5.2 Size of digi

22、ts 2 4.5.3 Direction of energy flow.3 4.6 Provisions for testing of calibration.3 4.6.1 Test output that is proportional to energy3 4.6.2 Test mode3 4.6.3 Delivered and received energy .3 4.6.4 Other measurements.3 4.7 Nameplate 3 4.7.1 Nameplate additions3 4.7.2 Nameplate deletions3 5 ACCEPTABLE PE

23、RFORMANCE OF NEW TYPES OF ELECTRICITY METERING DEVICES AND ASSOCIATED EQUIPMENT 3 5.1 General.3 5.1.1 Acceptable meters.3 5.2 Selection of metering devices for approval tests4 5.3 Conditions of test4 5.4 Rules governing the acceptance of types 4 5.5 Performance requirements.4 5.5.1 Test conditions 4

24、 5.5.2 Loading for accuracy tests 4 5.5.3 List of type tests 5 5.5.4 Accuracy tests .7 5.5.4.1 Test number 1: No load .7 5.5.4.2 Test number 2: Starting load .7 5.5.4.3 Test number 3: Load performance 7 5.5.4.4 Test number 4: Effect of variation of power factor.7 5.5.4.5 Test number 5: Effect of var

25、iation of voltage.9 5.5.4.6 Test number 6: Effect of variation of frequency.11 5.5.4.7 Test number 7: Equality of current circuits for multi-element meters11 5.5.4.8 Test number 8: Internal meter losses12 5.5.4.9 Test number 9: Temperature rise12 5.5.4.10 Test number 10: Effect of register friction1

26、2 5.5.4.11 Test number 11: Effect of internal heating.12 5.5.4.12 Test number 12: Effect of tilt 14 5.5.4.13 Test number 13: Stability of performance14 5.5.4.14 Test number 14: Effect of polyphase loading 14 5.5.5 External influences 14 iii ANSI C12.20-2010 5.5.5.1 Performance verification14 5.5.5.2

27、 Test number 15: Insulation 15 5.5.5.3 Test number 16: Voltage interruptions test .15 5.5.5.4 Test number 17: Effect of high voltage line surges .15 5.5.5.5 Test number 18: Effect of external magnetic field .15 5.5.5.6 Test number 19: Effect of variation of ambient temperature .15 5.5.5.7 Test numbe

28、r 20: Effect of temporary overloads 17 5.5.5.8 Test number 21: Effect of current surge in ground conductor.17 5.5.5.9 Test number 22: Effect of superimposed signals 18 5.5.5.10 Test number 23: Effect of voltage variation-secondary time base.18 5.5.5.11 Test number 24: Effect of variation of ambient

29、temperature-secondary time base.18 5.5.5.12 Test number 25: Effect of electrical fast transient/burst test18 5.5.5.13 Test number 26: Effect of radio frequency interference 18 5.5.5.14 Test number 27: Radio frequency conducted and radiated emission test 18 5.5.5.15 Test number 28: Effect of electros

30、tatic discharge (ESD).18 5.5.5.16 Test number 29: Effect of storage temperature .18 5.5.5.17 Test number 30: Effect of operating temperature 18 5.5.5.18 Test number 31: Effect of relative humidity18 5.5.5.19 Test number 32: Mechanical shock .18 5.5.5.20 Test number 33: Transportation drop 18 5.5.5.2

31、1 Test number 34: Mechanical vibration.18 5.5.5.22 Test number 35: Transportation vibration18 5.5.5.23 Test number 36: Weather simulation test 19 5.5.5.24 Test number 37: Salt-spray test.19 5.5.5.25 Test number 38: Raintightness 19 6 STANDARDS FOR IN-SERVICE PERFORMANCE 19 7 REQUIREMENTS APPLICABLE

32、TO DETACHABLE WATTHOUR METERS .19 8 REQUIREMENTS APPLICABLE TO BOTTOM-CONNECTED ELECTRICITY METERS19 9 PROCEDURE FOR ASSIGNING FORM DESIGNATIONS19 ANNEX A 20 A.1 Foreword to Second Edition (2002)20 A.2 Foreword to First Edition (1998) .22 iv ANSI C12.20-2010 Foreword (This Foreword is not part of Am

33、erican National Standard C12.20-2010.) This American National Standard establishes acceptable performance criteria for electricity meters. Accuracy class designations, current class designations, voltage and frequency ratings, test current values, service connection arrangements, pertinent dimension

34、s, form designations, and environmental tests are covered. The existing C12.20 Standard has been revised with the intent to bring it up to date in an industry that is changing dramatically because of both technology and regulatory matters. This American National Standard establishes acceptable perfo

35、rmance criteria for electricity meters. The existing standard was broadened to allow three phase current and voltage sources as an optional test method to the existing single phase, series, parallel method. In memoriam to Glenn Mayfield and Ed Malemezian: both had a passion for standards and members

36、 of SC16 felt fortunate to know and learn from them. Suggestions for improvement to this standard are welcome. They should be sent to: National Electrical Manufacturers Association Vice President, Technical Services 1300 North 17th Street Suite 1752 Rosslyn, VA 22209 This standard was processed and

37、approved for submittal to ANSI by Accredited Standards Committee for Electricity Metering, C12. At the time the committee approved this standard, the C12 Committee had the following members: Herman Millican, Chairperson ANS C12/SC16 Tom Nelson, Chairperson ANS C12 Paul Orr, Secretary ANS C12 Main Co

38、mmittee Organization Represented: Name of Representative: Organization Represented: Name of Representative: General InterestAustin Energy H. Millican Center for Neighborhood Technology L. Kotewa EnerNex Corporation A. Snyder Future DOS R rated voltage 1%; rated frequency 1 Hz; test amperes 1%; and u

39、nity power factor (0 2). The meter shall be stabilized at ambient temperature before performance tests are made. The reference performance shall be as close as practical to zero error and in no case shall exceed 0.2% error for accuracy class 0.5 or exceed 0.1% error for accuracy class 0.2. In this f

40、irst version of ANSI C12.20 to specify that Polyphase loading may be used for calibration type tests, a meter may meet the requirements of tests 18 and 13 using either series-parallel loading or polyphase loading. The calibration type tests described in tests 18 and 13 shall all be performed using t

41、he same loading; that loading may be either series-parallel or polyphase. 5.5.2 Loading for accuracy tests Unless otherwise specified, accuracy tests may be done with either series-parallel loading or polyphase loading. For series-parallel loading, the meter shall be tested with the voltage circuit(

42、s) effectively in parallel and with the appropriate current circuit(s) energized effectively in series. For polyphase loading, the meter shall be tested with voltage and current phase angles similar to actual service installations as described below (polyphase loading). When polyphase loading is use

43、d, the appropriate loading will depend on the meter configuration. Calibration tests done with polyphase loading shall pass for Typical Loading configurations as shown in Table 3. Alternate Loading configurations are shown for information only. The internal meter connections for these Form Designati

44、ons are provided in ANSI C12.10. Table 3 Polyphase Service loading for use on Accuracy Tests Description Form Designations Typical Loading Alternate Loading Two Element, Self Contained 12S, 13S, 25S, 13A Three wire, Network Three wire, 3 ,delta Two Element, Transformer Rated 5S, 26S, 35S, 45S, 56S,

45、5A, 35A, 45A Three wire, 3 , delta Three wire, 1 Three Element, Self Contained 16S, 16A Four wire, wye Four wire, delta Three Element, Self Contained 17S Four wire, delta None Three Element, Transformer Rated 9S, 10S, 39S, 9A, 10A, 48A Four wire, wye Four wire, delta 4 ANSI C12.20-2010 Polyphase loa

46、ding may be either ABC or CBA phase sequence. For ABC phase sequence, the voltage and current phase angles for unity power factor are shown in Table 4. Table 5 shows phase angles for CBA phase sequence. Angles represent the amount that phasors lag the A Phase Voltage. Table 4 ABC Phase Sequence, Cur

47、rent the meter shall show no damage and shall operate correctly in accordance with the requirement of the standard. Any change in energy and power quantities shall be limited to 1 least significant digit displayed. 5.5.5.2 Test number 15: Insulation Refer to subclause 4.7.3.1 of ANSI C12.1-2008. 5.5

48、.5.3 Test number 16: Voltage interruptions test Refer to subclause 4.7.3.2 of ANSI C12.1-2008. 5.5.5.4 Test number 17: Effect of high voltage line surges Refer to subclause 4.7.3.3 of ANSI C12.1-2008. 5.5.5.5 Test number 18: Effect of external magnetic field Refer to subclause 4.7.3.4 of ANSI C12.1-

49、2008 except that Table 20 (below) is to be used in place of Table 21 in ANSI C12.1-2008. Table 20 Effect of external magnetic field Current In Amperes Current Class Condition 2 10 20 100 200 320 Position of Conductor From ANSI C12.1-2008 Maximum Deviation In % From Reference Performance Reference performance for conditions (1), (2), and (3) 0.025 0.25 0.25 1.5 3 5 Reference Condition (1) 0.025 0.25 0.25 1.5 3 5 Condition (1) in Paragraph 4.7.3.4 1.0 Condition (2) 0.025 0.25 0.25 1.5 3 5 Condition (2) in Paragraph 4.7.3.4 1.0 Condition (3) 0.025 0.25 0.25 1.5 3 5 Co