NAVY W-F-2917-1997 FLOODLIGHT SET ELECTRIC DIESEL-ENGINE-DRIVEN TRAILER MOUNTED [Superseded NAVY MIL-F-29161 D CANC NOTICE 1 NAVY MIL-F-29161 D NAVY MIL-F-29161 C NAVY MIL-F-29161 .pdf

《NAVY W-F-2917-1997 FLOODLIGHT SET ELECTRIC DIESEL-ENGINE-DRIVEN TRAILER MOUNTED [Superseded NAVY MIL-F-29161 D CANC NOTICE 1 NAVY MIL-F-29161 D NAVY MIL-F-29161 C NAVY MIL-F-29161 .pdf》由会员分享，可在线阅读，更多相关《NAVY W-F-2917-1997 FLOODLIGHT SET ELECTRIC DIESEL-ENGINE-DRIVEN TRAILER MOUNTED [Superseded NAVY MIL-F-29161 D CANC NOTICE 1 NAVY MIL-F-29161 D NAVY MIL-F-29161 C NAVY MIL-F-29161 .pdf（17页珍藏版）》请在麦多课文档分享上搜索。

1、 INCH-POUND W-F-29 17 Januarv 17. 1997 SUPERSEDING 20 August 1993 MIL-F-29161D FEDERAL SPECIFICATION FLOODLIGHT SET, ELECTRIC, DIESEL-ENGINE-DRIVEN, TRAILER MOUNTED The General Services Administration has authorized the use of this specification by all Federal agencies. 1. SCOPE AND CLASSIFICATION 1

2、.1 Scope. This specification covers a self-contained, trailer-mounted, floodlight set, equipped with a diesel-engine-driven, 6000 watt (W) (20 473 British thermal units per hour (Stunir) generator and a mechanically operated telescoping floodlight tower. The floodlight set is intended for use at sho

3、re establishments and for military field application under ali kinds of climatic conditions. It is a completely self-contained unit, suitable for use as a source of electrical floodlighting in remote locations, with electrical power as an auxiliary feature. 2. APPLICABLE DOCUMENTS 2.1 Government pub

4、lications. The following documents, of the issue in effect on the date of invitation for bids or request for proposal, form a part of this specification to the extent specified herein. Military Standards MIL-STD-209 - Slinging and Tiedown Provisions for Lifting and Tying Down Military Equipment. Ben

5、eficial comments, recommendations, additions, deletions, clarifications, etc. and any data which may improve this document should be sent to: Commanding Officer, Naval Construction Battalion Center, Code 1581, 1000 23rd Avenue, Pori Hueneme, CA 93043-4301, by using the Standardization Document Impro

6、vement Proposal (DD Form 1426) appearing at the end of this document or bv letter. AMSC NIA FSC 6230 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- - W-F-2917 W 99999

7、74 0373233 693 = W-F-29 17 MIL-STD- 1223 - Nontactical Wheeled Vehicles Treatment, Painting, Identification MIL-STD-1791 Marking and Data Plate Standards. Design for Internal Aerial Delivery in Fixed Wing Aircraft. - (Copies of military standards required by contractors in connection with specific p

8、rocurement functions are obtained fi-om the Standardization Documents Order Desk, Bldg. 4D, 700 Robbins Avenue, Philadelphia, PA 19 1 1 1-5094.) 2.2 Other Government documents, drawings, and publications. The following other Government documents form a part of this specification on the extent specif

9、ied herein. DEPARTMENT OF TRANSPORTATION (DOT) Federal Motor Carrier Safety Regulations. (Application for copies should be addressed to the Superintendent of Documents, U. S. Government Printing Office, Washington, DC 20402.) 2.3 Other publications. The following other documents form a part of this

10、specification to the extent specied herein. Unless a specifc issue is identified, the issue in effect on date of invitation for bids or request for proposal shall apply. NATIONAL, ELECTRICAL MANUFACTURERS ASSOCIATION (NEMA) NEMA AB 1 - NEMA WD 1 - NEMA WD 6 - Molded Case Circuit Breakers and Molded

11、Case Switches. General Requirements for Wiring Devices. Wiring Devices, Specific Purpose. (Private sector and civil agencies may purchase copies of these voluntary standards from the National Electrical Manufacturers Association, 1300 North 17th Street, Suite 1847, Rosslyn, VA 22209.) NATIONAL FIRE

12、PROTECTION ASSOCIATION (NFPA) NFPA 70 - National Electrical Code. (Private sector and civil agencies may purchase copies of these voluntary standards fi-om the National Fire Protection Association, 1 Battery March Park, P.O. Box 9101, Quincy, MA 02269.) SOCIETY OF AUTOMOTIVE ENGINEERS, INC. (SAE) SA

13、E J560B - Seven-Conductor Electrical Connector for Truck-Trailer Jumper Cable. SAE J1292 - Automobile, Truck, Truck-Tractor, Trailer, and Motor Coach Wiring. 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-W-F-2937 M 999947Li 0373232 52T M W-F-29 1

14、7 (Private sector and civil agencies may purchase copies of these voluntary standards from the Society of Automotive Engineers, Inc., 400 Commonwealth Drive, Warrendale, PA 15096.) TIRE AND RIM ASSOCIATION, INC. (TRA) TRA Yearbook. (Private sector and civil agencies may purchase copies of these volu

15、ntary standards from the Tire and Rim Association, Inc., 175 Montrose West Avenue, Suite 150, Copley, OH 44321.) UNDERWRITERS LABORATORIES INC. (UL) UL 486A - UL 498 - Attachment Plugs and Receptacles. UL 1077 - Supplementary Protectors for Use in Electrical Equipment. Wire Connectors and Soldering

16、Lugs for Use With Copper Conductors. (Private sector and civil agencies may purchase copies of these voluntary standards from the Underwriters Laboratories Inc., 333 Pfingsten Road, Northbrook, IL 60062-2096.) OD activities may obtain copies of those adopted voluntary standards listed in the DoD Ind

17、ex of Specifications and Standards free of charge from the Standardization Document Order Desk, Building 4D, 700 Robbins Avenue, Philadelphia, PA, 191 11-5094.) 2.4 Order of precedence. In the event of a confiict between the text of this specification and the reference cited herein, the text of this

18、 specification shall take precedence. 3. REQUIREJMENTS 3.1 Description. The floodlight set shall consist basically of a trailer, mounted with a diesel- engine-driven generator, telescoping tower, with four 1 OOOW (341 2 Btu/hr) metal-halide floodlights and a portable mast for mounting two 500W (1706

19、 Btu/hr) tungsten halogen floodlights. The floodlights and all electrical equipment shall be provided with a weatherproof storage compartment. 3.1.1 Dimensions and weight. The overall dimensions and weight of the floodlight set in towable condition, attachments retracted and stowed, shall be not gre

20、ater than 15 feet (4.57 m) in length, 6.5 feet (i. 98 m) in height, and 2500 pounds (lb) (1134 kilograms (kg) in weight. 3.1.2 Environmental and storage conditions. All components of the floodlight set shall withstand, without damage or impairment of operation, environmental conditions including the

21、 following: a. Rated performance, without additional auxiliary equipment, in any ambient temperature fiom -25 degrees Fahrenheit (“F) to 125 OF (-3 1.7 degrees Celsius (OC) to 51.7 OC), or 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-W-F-2917 =

22、9999974 0173213 4bb 4 W-F-29 17 when exposed to raididi at a rate up to 3 inches (76 mm) per hour, impinging on the set at any angle from the vertical to 45 degrees from the vertical. b. The set shall not be damaged by exposed storage at temperatures from -65 OF to 155 OF (-53.9 OC to +68.3 OC) at a

23、ny possible relative humidity within this temperature range. 3.2 First article. The manufacturer shall fiiniish one floodlight trailer for first article inspection, test and approval (see 4.3 and 6.2). 3.3 Standard product. Except where modified herein, it is intended that the equipment and its comp

24、onent parts shall be a regular commercial product of the manufacturer or his suppliers. All equipment and parts shall be new and unused. 3.4 Alternator. The alternating current alternator shall be a brushless design with a rated output between 1600 and 2000 revolutions per minute (rpm), of not less

25、than 6000W (20 484 Btukr), 120/240 volts (V), 60 Hertz, single phase, alternating current. The alternator shall be rigidly coupled to the engine, permanently aligned and of singie bearing design. The alternator shall have a brushless exciter and voltage regulated for k 8 percent and +2 -8 percent ma

26、ximum from no load through maximum rated load. 3.4.1 Power distribution equipment. All electrical components shall conform to applicable UL standards (including UL 4864 UL 498, UL 1077) and to NFPA 70. The installation of all electrical components and systems shall conform to NFPA 70. The power dist

27、ribution equipment shall consist of the power distribution panel, ballasts for the metal halide lamps, switches, receptacles, cord connectors and plugs, portable power cords, interconnecting wiring, fittings, and accessories, installed and connected as required to provide a complete, operable system

28、. 3.4.1.1. Power distribution panel. The power distribution panel shall be a circuit breaker panel mounted in a readily accessible location within the floodlight set housing. Sufficient circuit breakers shall be contained in the panel to provide independent control and circuit protection as defined

29、in NFPA 70. 3.4.1.2 Circuit breakers. The circuit breakers shall conform to the requirements of NEMA Al3 1, and UL 1077. All circuit breakers shall be approved for use as switches and shall be marked as such. Circuit breakers shall be sized to have trip ratings as required for protection against ove

30、rloads, short circuits, and grounding in accordance with NFPA 70. 3.5 Materials. Materials used shall be fiee from defects which would adversely affect the performance or maintainability of individual components or of the overall assembly. Materials not specified herein shall be of the same quality

31、used for the intended purpose in commercial practice. Unless otherwise specified herein, all equipment, material, and articles incorporated in the work covered by this specification are to be new and fabricated using materials produced from recovered materials to the maximum extent possible without

32、jeopardizing the intended use. The term “recovered materials” means materials which have been collected or recovered from solid waste and reprocessed to become a source of raw materials, as opposed to virgin raw materials. 4 Provided by IHSNot for ResaleNo reproduction or networking permitted withou

33、t license from IHS-,-,- W-F-2917 = 9999974 0173214 3T2 4 W-F-29 17 Unless otherwise specified, none of the above shall be interpreted to mean that the use of used or rebuilt products is allowed under this specification. 3.6 Floodlight set components. 3.6.1 Generator set. The generator set shall be a

34、 unitized engine driven alternator. The generator set shall provide adequate electrical power for operation of the floodlight set at rated maximum load during environmental and test conditions specified herein. The generator set shall be mounted to minimize vibration. 3.6.2 Engine. The engine shall

35、be a four stroke cycle, compression ignition, direct injection, diesel fueled unit, governed to provide 60 hz power at any load up to rated output of the alternator 6000W (20 473 Btukr). The engine shall be furnished, as a minimum, with the following: a. 12V electric starting system. b. 12V, direct

36、current battery charging unit. c. “Glow plug” preheater system. d. Totalizing engine hour meter (control panel mounted). e. Fuel tank level gauge. f. Direct current voltmeter to indicate battery potential (control panel mounted). 3.6.2.1 Engine fuel. The diesel engine shall operate efficiently on DG

37、-1, DG-2, DF-A, and DF-M as primary fuels, and be capable of operation on jet fuels JP-4, JP-5, and JP-8. The engine fuel system shall be provided with a filter and water separator which may be installed separately or as a combined type. 3.6.2.2 Fuel tank. The fuel tank shall be of sufficient capaci

38、ty to permit full load operation for a minimum of 18 hours. The fuel tank shall be removable from the floodlight set to permit cleaning and shall contain a he1 shut-off valve at the outlet connection. A fuel tank drain, located on the tank to provide complete emptying of the tank, shall be provided.

39、 3.6.3 Wiring. Conductors for interconnecting wiring shall be composed of annealed copper wire and have a flame-retardant and oil-resistant covering conforming to NFPA 70. Extra flexible . conductors shall be used where relative movement between parts may occur. Wire connectors and terminals shall b

40、e the crimp type where practicable and shall be attached in a manner to fully protect the insulation; all wire connectors shall be copper and conform to UL 486A. Conductors shall be properly clamped in a neat manner and protected by grommets or other suitable protection from abrasion where the condu

41、ctors pass through metal. 3.6.3.1 Ballasts. The ballasts for the four 1OOOW (3414 Btu/hr) metal halide lamps shall be the peak-load type designed to operate with 120/240V input. Each ballast shall be the enclosed constant wattage auto-transformer type, and shall be designed for operation at low temp

42、eratures down to -25 OF (-32 OC). The ballast shall be the plug-in type and mounted near the power distribution panel in a protected location inside the storage compartment. The line side of the ballasts shall be connected to the circuit breakers in the distribution panel. 5 Provided by IHSNot for R

43、esaleNo reproduction or networking permitted without license from IHS-,-,- W-F-2917 m 9999974 0173215 239 = b W-F-29 17 3.6.3.2 Connectors, plugs, and receptacles. Cord receptacles, cord plugs, and outlet receptacles shall be of the grounding type and shall be in accordance with UL 498, NEMA WD 1 an

44、d NEMA WD 6, as applicable. The cord receptacles and cord plugs shall employ cord grip construction and shall be weatherproof Cord plugs and cord connectors utiiiziig weatherproof cord grips shall be so designed that they will form a weatherproof seal when the plug is inserted into the mating connec

45、tor either of another cord or an outlet on the control panel. All receptacles exposed to the weather shall be equipped with spring loaded cover plates. 3.6.3.3 Receptacles. Two grounding type two-pole, three-wire, 125V, 154 general purpose duplex receptacles conforming to NEMA WD 1 configuration 5-1

46、5R; and two grounding type three-pole, four-wire, 240V, 204 single locking type receptacles conforming to UL 498 and NEMA WD 6 configuration L16-20R shall be installed in the same vicinity of each other in an accessible, protected location on the exterior of the storage compartment. The locking type

47、 receptacles shall be used for the 500W (1706 Btu/hr) and 1OOOW (3412 BW) luminaries. The general purpose duplex receptacles shall be used for auxiliary equipment. Each outlet shall be marked with voltages and current rating. Each duplex receptacles shall be connected to oniy one circuit so that one

48、 circuit breaker protects one duplex receptacle load. The input to each pair of ballast shall be connected to a multi-wire 120/240V circuit with a common neutral so that two circuit breakers, one for each ungrounded conductor, protect the ballasts. The circuit breaker for each luminary shall also fu

49、nction as the switch for controlling each flood lamp. 3.6.3.4 Portable power cord. One portable power cord shall be provided for use as power extension cord for the 500W (1707 BtUnir) luminaries mounted on the portable mast. The cord shall be stranded wire, total not less than 150 feet (45.72 m) in length and shall be 3 conductor, No. 14 American Wire Gage (AWG) copper conductors. One end of the cord shall be terminated in a plug connector conforming NEMA WD 6. The other en